HOTOWELL HTW-31-KT13T Series User manual

Wireless Thermostat(Transmitter)
Reference No.:HTW-31-KT13T Series
Functions
Technical Data
HTW-31-KT13T wireless thermostat(Transmitter) is used in
heating only or cooling only systems to maintain selected
room temperature. The controller acquires the room
temperature with its integrated sensor and maintains the set
point by deli ering control commands.
 Large display can be clearly read with the background lighting.
 Four buttons make it easy to use.
 MAN Mode and PRG. Mode
 4 periods of each day programmable(5+1+1)
 The display shows the set temperature as well as the measured temperature, time.
 Temperature display in degrees Celsius.
Thermostat operating oltage: 2 x AAA, alkaline batteries.
Frequency: 868Mhz/433Mhz
Channel selection: By programming the thermostat and the recei er.
Switching options: 5+1+1
Temperature settings: 5°C ~ 30°C, 0.5°C increments.
Accuracy: +/- 0.5°C
Thermostat dimensions: Surface mounted, 135mm x 87.5 mm x 23.2mm.
Color: White
IP protection rating: 30.
C e r t i f i ca t i on: C E / R o H S
General

Wireless Thermostat(Transmitter)
Reference No.:HTW-31-KT13T Series
（
）
Week/Day
Time MAN Mode
PRG. Mode
Room Temp.
Set Temp.
Heat Icon
Mode Select & Time Adju t &
Sen or Calibration Button
Programming Buttong &
MAN/PRG. Mode Select
PRG Period
On/off Button
Long press PRG button to enter PRG setting. The weekday is fixed from Monday to Sunday(1~7),
each day ha e 4 periods(1~4). Each press of PRG button can into next item setting.
The time and temperature of each period i can be set in following steps.
1). Press PRG and hold for 3 seconds, the time display flash, change the alue by + and - button.
each press is 15mins
2) Press PRG button , the temperature display flash, change the temperature by + and - button.
3). Press PRG button to next period.
4). The other period settings follow the same way.
Example:
Monday to Friday Saturday Sunday
Period 1 2 3 4 1 2 3 4 1 2 3 4
Time 6:30 8:00 18:00 22:30 8:00 10:00 18:00 23:00 9:00 12:00 19:00 0:00
Temp. 21°C 18°C 21°C 16°C 21°C 21°C 21°C 16°C 23°C 21°C 16°C 21°C
PRG. Schedule Setting
Displa & Buttons

Wireless Thermostat(Transmitter)
Reference No.:HTW-31-KT13T Series
Temp. Calibration
Code Pairing & Code Unlink(If With)
- Press and hold the SET button for around 3 seconds. The minutes display (top left in
the display) flashes.
- Change this alue using the + and – buttons.
- Press the SET button . The hour display (top left in the display) flashes.
- Change this alue using the + and – buttons.
- Press the SET button. The day display (top left in the display) will flash as a number.
- Change this alue using the + and – buttons. Use 1 for Monday, 2 for Tuesday, 3 for
Wednesday, 4 for Thursday, 5 for Friday, 6 for Saturday and 7 for Sunday.
Turn thermostat off, long press SET button to enter Sensor calibration. Range: -8°C~+8°C
a) At control centre(HTW-31-X8 ), press KEY button(K1-K8), indicator flashing
b) On thermostat, turn off thermostat, hold “SET” button for 3 seconds, it will show the code on
dispaly, then press “SET” button again,, until the indicator on control centre(LED1-LED8) stop
flashing, code pairing finish.
c) You can check if thermostat and HTW-31-X8 work fine by setting the temp higher than room
temp, then system should start heating, when heating, the LED on HTW-31-X8 will on, that
means the corresponding actuator is working now. ID Pair success.
d) If you want unlink the thermostat and HTW-31-X8 channel, you can power off HTW-31-X8, then
power on the HTW-31-X8 and long press the channel KEY button within 1 minutes, when you
see that Channel on and off, the unlink success.
Clock Adjustment

Wireless Thermostat(Transmitter)
Reference No.:HTW-31-KT13T Series
Dimensions
Transmitter
Mount on wall: Separate the face plate and base plate, and mount the base plate on the wall
with pro ide screws. After done, hung the face plate on base plate
Put on desk: install the foot directly .
Unit：mm
Installation