Hotron Domino 1100 RC Manual

FITTING AND OPERATING INSTRUCTIONS
DOMINO 1100 RC
DOMINO 1XXX, other versions
Radar motion sensors for the detection of objects for automatic gates.
SAFETY INFORMATION
The unit is only to be operated with voltages that comply with the
Safety Extra-Low Voltage (SELV) requirements in safety
standards based on IEC 60950. This unit is only to be installed
and maintained by trained, qualified personnel.
1. FITTING
1.1 OPENING THE RADAR SENSOR UNIT 1.2 DRILLING
from the rear, prior to installation from the front, after installation Stick the drilling template in place and drill
according to the instructions
1.3 FASTENING AND CONNECTING-UP
Draw the cable through the opening provided Connect the cable to the terminals
1 power supply AC/DC brown
2 power supply AC/DC green
3 Main relay white
4 Main relay yellow
Vehicle relay grey
Vehicle rela
y
p
ink
Fasten the base plate with the screws contained in the housing,
to remove and insert the electronics, observe the instructions in point 2.3
1.4 OTHER INSTALLATION OPTIONS
Optional accessory out of the 4tec accessory range.
Ceiling-mounting with mounting bracket
or
Wall fastening with weather-cap set

1.5 SETTING UP THE RADAR SENSOR 1.6 CLOSING THE RADAR SENSOR UNIT
1. Switch on the unit and wait 10 seconds (LED flashes red/green) Insert the cover from the top and press until it clicks in place
2. Adjust the radar sensor unit / Check the setting by pacing out the distance
fitting height 7 m
fitting height 5 m
/main relay
y
2 DIMENSIONS OF THE DETECTION AREA
ca. 5 m
ca. 8 m
ca. 6 m
ca. 7 m
. SETTINGS
EM
) Antenna
r
4) Main relay
2.4 POSITION OF THE DETECTION AREA
o make an adjustment, take hold of the prin
ENTS
1
4 6
2
.1 OPERATING EL2
1
2) IR-receiver
3) IR-transmitte
7
98 10
5
5) Terminal
(power supply )
6) Vehicle relay
7) Terminal
(vehicle rela )
8) Button/Menu
9) Button/Value
10) LED
2 3
2.3 CHOICE AND EXCHANGE OF ANTENNA2.
ettings: Detection area angle 30° Optional out of the 4tec accessory range.
and sensitivity max. VALUE 16
S
ted
he position can be adjusted in 5° steps from 0° to 40°.
Static sensitive devices.
erent characteristics
, withdraw it carefully with two fingers and
Do not use any metallic
tools!
Changing the antenna allows to realise diff
of the detection area.
To change the antenna
then insert the new antenna.
T
circuit board by the edge, pull it forward, and
then place it in the desired position.
T
The factory setting is 15°, notches can be broken out.

The printed circuit board can also be inserted at a slant angle. 2.5 SIZE OF THE DETECTION AREA / SENSITIVITY
imum 3 steps to the right or to the left! The sensitivity potentiometer control enables the size of the
6 DESCRIPTION OF THE DIFFERENT CONFIGURATION CHARACTERISTICS OF THE RADAR SENSOR UNIT
(mono) with direction recognition (stereo)
Turn max
detection area to be adjusted.
2.
etection characteristicsD
ithout direction recognitionw
ross traffic fade-out
mit Richtungserkennung (stereo)
forwards (towards the radar sensor unit) backwards (away from the radar sensor unit)forwards / backwards
The direction recognition can completely be switched off. The radar sensor unit will not detect any movements and if the relay contact will be changed now
high sensitivity = big detection area
low sensitivity = small detection area
the gate remains constant open or closed.
C
Settings selectively: low, medium or high
especially suited to fitting
angles of 25° to 40°
If the cross traffic fade-out function is switched on, the gate will open only if the
motion is towards the gate.

People- vehicle detection
The radar is able to analyse motions from people or vehicles different and to switch, according to the settings,
the main relay, the vehicle relay or both relay at the same time.
Relay functions
The main relay switches always, that means for people and vehicles detection.
The vehicle relay switches only if the vehicle detection is activated and a vehicle will move inside the detection area.
Examples of use
Gate with separate pedestrian door. Gate control unit with 1 input.
Vehicle detection activated, only the vehicle relay is connected to the Gate control unit
Vehicle approaches, Person approaches,
vehicle relay switches, vehicle relay switches not,
(LED fast flashing green/red) Gate remains closed,
g
ate opens person uses the pedestrian doo
r
main relays vehicle relays
DOMINO 1100 RC
GATE CONTROL UNIT
Gate without separate pedestrian door. Gate control unit with 2 inputs.
Vehicle detection activated, vehicle relay and main relay are connected to the Gate
control unit
Person approaches, Vehicle approaches,
main relay switches, vehicle relay switches,
(LED lights red) (LED fast flashing green/red)
gate opens half gate opens completely
main relays vehicle relays
DOMINO 1100 RC
GATE CONTROL UNIT
2.7 LED STATUS DISPLAY
LED
green unit ready for operation
red main relay active
green/red fast flashing vehicle relay active
green/red slow flashing initialisation (for 10 seconds after switching on)
green flashing command received
red flashin
g
erro
r

2.8 CONFIGURATION OF THE RADAR SENSOR UNIT
SETTINGS WITH BUTTONS
LED green/red
IR-receiver
IR-transmitter
Button MENU
Button VALUE
Programming mode
The programming mode allows to adjust the radar sensor unit with two push buttons. All settings can be read out the below programming table.
The LED flashing order shows the respective settings.
While the programming mode is activated the IR-communication is blocked but the sensor functions are still active.
If during 10 minutes no settings have been done the programming mode will be quitted and all settings will be saved automatically.
START: Activate programming mode
Push button MENU for approx. 2s, programming mode is activated LED is flashing. The flashing order shows the actual settings.
LED flashing red number corresponding MENU nr. LED flashing green number corresponding VALUE nr.
the LED does not flash if the VALUE is = 0
STOP: Leave programming mode
Push button MENU for approx. 2s, programming mode is quitted all settings are automatically saved
Set MENU or VALUE →watch programming table
push button MENU 1x short = increase MENU 1 step
Is the maximum menu nr. reached, the programming starts again with the lowest menu nr., i.e. 1x push = 1 step forwards
push button VALUE 1x short = increase VALUE 1 step
Is the maximum value reached, the programming starts again with the lowest value, i.e. 1x push = 1 step forwards
When the MENU or VALUE buttons be pushed, the flashing code stops and restarts flashing with the new value.
After each change the setting will be automatically saved.
Programming sample: Change the output hold time from 1.0 s to 3.0 s
push button MENU approx. 2s = start programming
LED flashing 1x red and 8x green = MENU sensitivity, VALUE 8
push button MENU 3x
LED flashing 4x red and 3x green = output hold time VALUE 1.0 s
push button VALUE 3x
LED flashing 4x red and 6x green = output hold time VALUE 3.0 s
push button MENU approx. 2s = stop programming, setting automatically saved
Programming table
MENU
red LED
flashing according no
e.g. 3x red = vehicle
detection
VALUE
green LED
flashing according value
0 = LED not flashing!
DESCRIPTION
Start: push button MENU for approx. 2s
Stop: push button MENU for approx. 2s
Reset: push button MENU and VALUE at the same time for approx. 2s
LED flashing for approx. 10s green/red
1
Sensitivity 1 - 16 1 = lowest sensitivity = small detection area 16 = highest sensitivity = big detection area
2
Detection mode
0
1
2
3
off
stereo forwards
stereo backwards
mono
off = no detection possible
detects motion towards the radar sensor unit
detects motion away from the radar sensor unit
detects motion forwards and backwards
3
Vehicle detection
0
1
2
3
off
low
medium
high
off = no detection the vehicle relays does not switch
only vehicles will be detected
the settings low, medium and high allow to set the sensor accurate according to the localization
4
Output hold time
0
1
2
3
4
5
6
7
8
off
0.2s
0.5s
1.0s
1.5s
2.0s
3.0s
4.0s
5.0s
off = relay does not switch
0.2s = smallest hold time
1.0s = factory setting
5.0s = biggest hold time
5
Relay contact
1
2
N.O.
N.C.
contact will close by detection detection mode switched off and the change of relay contact
contact will open by detection will keep the gate constant open or closed
6
Fade out cross traffic
0
1
2
3
off
low
medium
high
all movements well be detected
cross traffic will be fade out
the settings low, medium and high allow to set the sensor accurate according to the localization
7
Sensor address 1 – 16
The sensor address is needed for the programming with remote control. The address can be
choose and changed with buttons. The sensor address must be changed only if there are more
than one sensor inside the range of the remote control.

SETTINGS WITH REMOTE CONTROL Domi-LINK
The Domi-LINK allows to set the radar sensor unit easy, fast and perfectly from the floor.
While the programming the sensor functions are still active. The settings can be checked immediately.
Low batteries (shown on the Domi-LINK display), sunlight, fluorescent lamps and wrong orientation of Domi-LINK
can reduce the range and cause transmission errors.
For safety reasons the IR-programming mode will be intermitted after 30 min., alternatively completely blocked.
To unlock the programming mode, push the MENU or VALUE button at the radar sensor unit or cut the power supply for a few seconds.
Establish connection
Before starting the programming please read the Domi-LINK operating instructions!
Sensor switched of and ready for operation, LED is green.
Domi-LINK must point frontal at the sensor.
For a perfect transmission the
sensor angle (0 – 40°) should
Sensor list
Domino 100X RC
Domino 101X RC
Domino 102X RC
Domino 110X RC
also be considered.
Choose the Domino 110X RC from the sensor list shown at the Domi-LINK LCD-display.
After that select the address, only necessary if more than one sensor is inside the range of Domi-LINK.
Programming the address →have a look at the settings with buttons.
The address can be selected from the list or can be read out with “search address“.
Domino 110X RC
search address
address 2
address 3
address 4
address 1
The mark show the selected address.
Push the select button to establish a connection to the radar sensor unit.
If the connection is established, on LCD display will be shown a list with all settings.
The mark shows the current settings.
If the sensor is encoded, the display will show “enter code”.
The code can be set with the for Domi-LINK push buttons.
As soon as the fourth digit has been set the code will be transmitted.
_ _ _ _
enter code
Domino 110X RC
Detection mode
Vehicle detection
Output hold time
Relays contact
F
ade
ou
t
c
r
oss
tr
a
ffi
c
Sensitivity
√
If the code is correct a selection list will appear on display.
Start settings
The four push buttons allow to select the desired settings shown on display.
With “read value” the current setting can be read out and shown on display. The required value can be
selected with the arrow push buttons and confirmed and transmitted with pushing the select button.
The mark shows immediately the new value.
If the transmission was not OK the error will appear on display and the transmission has to be repeated.
Sensitivity
read value
1 min
2
3
4
The new setting can be read out immediately after the transmission.
Programming table Domi-LINK
MENU SETTINGS DESCRIPTION
Sensitivity 1 – 16 1 = lowest sensitivity = small detection area
16 = highest sensitivity = big detection area
Detection mode off
stereo forwards
stereo backwards
mono
off = no detection possible
detects motion towards the radar sensor unit
detects motion away from the radar sensor unit
detects motion forwards and backwards
Vehicle detection off
low
medium
high
off = no detection the vehicle relays does not switch
only vehicles will be detected
the settings low, medium and high allow to set the sensor accurate according to the localization
Output hold time off
0.2s
0.5s
1.0s
1.5s
2.0s
3.0s
4.0s
5.0s
off = relay does not switch
0.2s = smallest hold time
1.0s = factory setting
5.0s = biggest hold time
Relay contact N.O.
N.C.
contact will close by detection detection mode switched off and the change of relay contact
contact will open by detection will keep the gate constant open or closed
Fade out cross traffic off
low
medium
high
all movements well be detected
cross traffic will be fade out
the settings low, medium and high allow to set the sensor accurate according to the localization
Reset put all values back on factory setting
Code access with code
*lock access
access without code
set an access code access to programming mode only with code possible
code and programming mode will be locked immediately, new access not possible anymore*
code will be deleted, programming mode is free access to programming mode without code possible
Disconnect leave programming mode, access is encoded, decoded or locked immediately, according to setting
* lock access
If you lock access, the programming mode will be locked immediately. The radar sensor unit will not accept any commands from the remote control.
To unlock the programming mode, push the MENU or VALUE button at the radar sensor unit or cut the power supply for a few seconds.

3. DISTURBING INFLUENCES / INSTALLATION RECOMMENDATIONS
In this case the installation of
a weather-cap out of the 4tec
accessory range would be
recommended.
The radar sensor unit must be installed on a firm surface. The radar sensor unit must not be No moving objects (e.g. fans, plants, trees,
It must not be subject to vibration. installed behind a panel or other cover. flags, etc.) are permitted in the detection
area of the radar sensor unit.
The radar sensor unit should be installed in a position The radar sensor unit should not be fitted
where it is protected from rain. close to fluorescent lamps.
4. FAULT RECTIFICATION
Gate sees itself →reduce sensitivity, position radar sensor unit further forwards
LED fails to illuminate →no current, unit defective
5. SCOPE OF DELIVERY 6. OPTIONAL ACCESSORIES
- Domino 1100 - Domi-LINK (remote control)
- connecting cable - ceiling-mounting bracket
- fitting screws - weather-cap set (ceiling-mounting bracket included)
- self-adhesive drilling template
7. TECHNICAL DATA
Supply voltage 12-36 V DC/ 12-28 V AC
Current consumption approx. ca. 50 mA @ 24 V DC, 20°C
Power < 1 W
Microwave module K-band 24.05 GHz–24.25 GHz
Transmitting power < 20 dBm
2 Relay outputs NO or NC
Nominal power 0.5 A 120 V AC / 1A 24 V DC
max. breaking capacity 24 W / 60 VA
max. breaking voltage 120 V AC / 60 V DC
max. switching current 1 A
Stop period 0.2 s – 5 s
Temperature range -20°C to +60°C / -4°F to +140°F
Atmospheric humidity 0 to 90 % RH, non-condensing
Protection class IP54
Housing material Ground plate ABS, cover Polycarbonate
Dimensions 123 mm (W) x 65 mm (H) x 57 mm (D)
Weight 120 g
max. installation height 7 m
Electromagnetic compatibility CE in accordance with EMC directive 89/336/EEC
min. detection speed 0.1 m/s
Approval CETECOM, test report no.: 2-3279-01-01/03
Quality Made in Switzerland
CE0682 !
This unit complies with the requirements of the European R&TTE directive.
The declaration of conformity can be called up on the following website: www.4tec-ag.ch
4 TEC AG, Rietbergstrasse 49, CH-9403 Goldach, T [phone], F [phone], mailto:[email protected], www.4tec-ag.ch