HP cc2300 User manual

Manufacturing Part Number: A6900-96002
HP®cc3300 Carrier Grade Server
Quick Start Guide
Document Release Date: July 2002
This guide contains basic instructions for setting up the system and accessing
the Product Guide from the CD.

The HP cc3300 Carrier Grade Server may contain design defects or errors known as errata which may cause the product to
deviate from published specifications.
Information in this document is provided in connection with Intel®products. No license, express or implied, by estoppel or
otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel's Terms and Conditions
of Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating
to sale and/or use of Intel products including liability or warranties relating to fitness for a particular purpose, merchantability,
or infringement of any patent, copyright or other intellectual property right. Intel products are not designed, intended or
authorized for use in any medical, life saving, or life sustaining applications or for any other application in which the failure of
the HP product could create a situation where personal injury or death may occur. Intel may make changes to specifications
and product descriptions at any time, without notice.
This document contains information on products in the design phase of development. The information here is subject to
change without notice. Do not finalize a design with this information.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Intel is a registered trademark of Intel Corporation or its subsidiaries in the United States and other countries.
†Other names and brands may be claimed as the property of others.
Copyright © 2002 HP Corporation. All rights reserved. No part of this document may be copied, or reproduced in any form,
or by any means without prior written consent of Intel.

HP cc3300 Carrier Grade Server iii
Quick Start Guide
Contents
Specifications .......................................................................................................5
Regulatory Specifications and Disclaimers ......................................................6
Declaration of the Manufacturer or Importer..........................................................................6
Safety Compliance .......................................................................................................6
Electromagnetic Compatibility (EMC) ...........................................................................6
FCC Electromagnetic Compatibility Notice (USA).........................................................7
FCC Declaration of Conformity.....................................................................................7
Electromagnetic Compatibility Notices (International) ...................................................7
Removing the Server from the Box ....................................................................9
Removing the Server from the Box ....................................................................9
Selecting a Site .....................................................................................................................9
Checking the Power Connection .........................................................................................10
Connections and Controls ...................................................................................................13
Back Panel .................................................................................................................16
Connecting the Monitor, Keyboard, and Mouse...................................................................17
Applying Power for the First Time........................................................................................17
Warnings .............................................................................................................19
WARNING: English (US)....................................................................................................20
AVERTISSEMENTS : Français ..........................................................................................22
WARNUNG: Deutsch .........................................................................................................24
AVVERTENZA: Italiano......................................................................................................26
ADVERTENCIA: Español...................................................................................................28

iv HP cc3300 Carrier Grade Server
Quick Start Guide

HP cc3300 Carrier Grade Server 5
Quick Start Guide
Specifications
Table 1. cc3300 Carrier Grade Server Physical Specifications
Specification Value
Height 3.5 inches (89 mm)
Width 17.5 inches (445 mm)
Depth 20 inches (508 mm)
Front clearance 2 inches (76 mm)
Side clearance 1 inches (25 mm)
Rear clearance 3.6 inches (92 mm)
Weight 35 Lbs (15.9kg)
Figure 1. Front View

6 HP cc3300 Carrier Grade Server
Quick Start Guide
Regulatory Specifications and Disclaimers
Declaration of the Manufacturer or Importer
We hereby certify that this product is in compliance with European Union EMC Directive
89/336/EEC, using standards EN55022 (Class A) and EN55024 and Low Voltage Directive
73/23/EEC, Standard EN60950.
Safety Compliance
USA: UL 1950 – 3rd Edition/CSA 22.2. No. 950-M93
Canada: UL Certified – 3rd Edition/CSA 22.2. No. 950-M93 for Canada (product bears
the single UL mark for U.S. and Canada)
Europe: Low Voltage Directive, 73/23/EECTUV/GS to EN60950 2nd Edition with
Amendments, A1 = A2 + A3 + A4
International: TUV/CB to IEC 60950 3rd Edition, EN60 950 2nd Edition + Amd 1-4,
EMKO-TSE (74-SEC) 207/94 plus international deviations
Australian / New Zealand: CB Report to IEC 60950, 3rd Edition plus Australian deviations
Electromagnetic Compatibility (EMC)
USA: FCC CFR 47 Part 2 and 15, Verified Class A Limit
Canada: IC ICES-003 Class A Limit
Europe: EMC Directive, 89/336/EEC
· EN55022, Class A Limit, Radiated & Conducted Emissions
· EN55024, ITE Specific Immunity Standard
· EN61000-4-2, ESD Immunity (Level 2 Contact Discharge, Level 3 Air Discharge)
· EN61000-4-3, Radiated Immunity (Level 2)
· EN61000-4-4, Electrical Fast Transient (Level 2)
· EN61000-4-5, AC Surge
· EN61000-4-6, Conducted RF
· EN61000-4-8, Power Frequency Magnetic Fields
· EN61000-4-11, Voltage Dips and Interrupts
· EN61000-3-2, Limit for Harmonic Current Emissions
· EN61000-3-3, Voltage Flicker
Japan: VCCI Class A ITE (CISPR 22, Class A Limit) IEC 1000-3-2 Limit for Harmonic Current
Emissions
Australia/New
Zealand:
AS/NZS 3548, Class A
Taiwan: BSMI Approval, Class A
Korea: RRL Approval, Class A
Russia: GOST Approved
International: CISPR 22, Class A Limit

HP cc3300 Carrier Grade Server 7
Quick Start Guide
FCC Electromagnetic Compatibility Notice (USA)
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operating in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference. In this
case, the user is required to correct the interference at their own expense. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on; the user is encouraged to try to correct the interference by one or more of the
following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and the receiver.
· Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
· Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the grantee of this device could void the
user’s authority to operate the equipment. The customer is responsible for ensuring compliance of
the modified product.
FCC Declaration of Conformity
Product Type: cc3300 Carrier Grade
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Electromagnetic Compatibility Notices (International)
Europe (CE Declaration of Conformity)
This product has been tested in accordance too, and complies with the Low Voltage Directive
(73/23/EEC) and EMC Directive (89/336/EEC). The product has been marked with the CE Mark to
illustrate its compliance.

8 HP cc3300 Carrier Grade Server
Quick Start Guide
Japan EMC Compatibility
English translation of the notice above:
This is a Class A product based on the standard of the Voluntary Control Council for Interference
by Information Technology Equipment (VCCI). If this equipment is used in a domestic
environment, radio disturbance may arise. When such trouble occurs, the user may be required to
take corrective actions.
ICES-003 (Canada)
Cet appareil numérique respecte les limites bruits radioélectriques applicables aux appareils
numériques de Classe A prescrites dans la norme sur le matériel brouilleur: “Appareils
Numériques”, NMB-003 édictée par le Ministre Canadian des Communications.
English translation of the notice above:
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital
apparatus set out in the interference-causing equipment standard entitled “Digital Apparatus,”
ICES-003 of the Canadian Department of Communications.
BSMI (Taiwan)
The BSMI Certification number and the following warning is located on the product safety label
which is located visibly on the external chassis.

HP cc3300 Carrier Grade Server 9
Quick Start Guide
Removing the Server from the Box
Carefully unpack the server. Save all packing materials in case the server needs to be shipped at a
later time.
Selecting a Site
The server operates reliably within normal office environmental limits. Select a site that meets
these criteria:
· Clean and relatively free of excess dust.
· Well-ventilated and away from sources of heat, with the ventilating openings on the server kept
free of obstructions.
· Away from sources of vibration or physical shock.
· Isolated from strong electromagnetic fields and noise caused by electrical devices such as
elevators, copy machines, air conditioners, large fans, large electric motors, radio and TV
transmitters, and high-frequency security devices.
For AC-powered servers:
· Place the server near a properly earthed, grounded, three-pronged power outlet.
¾ In the United States and Canada: a NEMA-compliant, 110-125 V outlet rated for 20 amps
¾ In other geographic areas: a properly earthed, grounded outlet in accordance with the local
electrical authorities and electrical code of the region.
For DC-powered servers:
· Place the server near a -48 to -60 V DC supply.
· Verify that proper DC grounding is provided.
· Verify that proper insulation protects the DC connection terminals and wires.
CAUTION, ESD precautions
Electrostatic discharge (ESD) can damage disk drives, add-in boards, and
other parts. This server can withstand normal levels of environmental ESD.
However, we recommend doing all procedures in this guide only at an
ESD-protected workstation. If one is not available, you can provide some
ESD protection by wearing an anti-static wrist strap attached to chassis
ground of the server when handling components (e.g. any unpainted metal
surface).
CAUTION, Use grounded outlet
Make sure that the power service connection is through a properly grounded
outlet.

10 HP cc3300 Carrier Grade Server
Quick Start Guide
Checking the Power Connection
WARNING
The Power button on the Front Control Panel of the server does not
completely remove AC power. To completely remove AC power from
the server, you must unplug/disconnect the power connection from the
system. Unplugging/disconnecting the power connection removes the
+12 Volt standby power that is present when the server is powered
down.
WARNING
Do not modify or use a supplied AC power cord if it is not the exact type
required in the region where the server will be installed and used.
Replace the cord with the correct type. Refer to the cord requirements
described below.
Do not connect power to the server (AC or DC) if you will be adding
internal parts (boards, DIMMs, removable media drives). For these
installation procedures, see the HP®cc3300 Carrier Server Product
Guide.
WARNING
The DC power source may produce hazardous voltage levels
exceeding –60 VDC and high energy levels above 240VA that may cause
electric shock or burns. All DC input connections should be made only
by a qualified service person only to prevent injury. All wiring terminals
connected to the DC input terminal block must be fully insulated with no
exposed bare metal.
If AC power supplies are installed:
Mains AC power disconnect: The AC power cord(s) is considered the
mains disconnect for the server and must be readily accessible when
installed. If the individual server power cord(s) will not be readily
accessible for disconnection then you are responsible for installing an
AC power disconnect for the entire rack unit. This mains disconnect
must be readily accessible, and it must be labeled as controlling power to
the entire rack, not just to the server(s). To remove all power, two
AC cords must be removed.

HP cc3300 Carrier Grade Server 11
Quick Start Guide
Grounding the rack installation: To avoid the potential for an electrical
shock hazard, you must include a third wire safety ground conductor
with the rack installation. If the server power cord is plugged into an
AC outlet that is part of the rack, then you must provide proper
grounding for the rack itself. If the server power cord is plugged into a
wall AC outlet, the safety ground conductor in the power cord provides
proper grounding only for the server. You must provide additional,
proper grounding for the rack and other devices installed in it.
Overcurrent protection: The server is designed for an AC line voltage
source with up to 20 amperes of overcurrent protection per cord feed. If
the power system for the equipment rack is installed on a branch circuit
with more than 20 amperes of protection, you must provide
supplemental protection for the server. The overall current rating of a
server configured with two power supplies is less than 4 amperes.
If DC power supplies are installed:
The DC source must be electrically isolated by double or reinforced
insulation from any hazardous AC or DC source. The DC source must
be capable of providing up to 300 W of continuous power per feed pair.
Connection with a DC source should only be performed by trained
service personnel.
Mains DC power disconnect: You are responsible for installing a
DC power disconnect for the entire rack unit. This mains disconnect
must be readily accessible, and it must be labeled as controlling power
to the entire unit, not just to the servers(s).
Grounding the rack installation: To avoid the potential for an electrical
shock hazard, you must include a third wire safety ground conductor
with the rack installation. The safety grounding conductor must be a
minimum 14AWG connected to the earth ground stud on the rear of the
server. The safety ground conductor should be connected to the chassis
stud with a two hole crimp terminal with a maximum width of 0.25 inch.
The nuts on the chassis studs should be installed with a 10 in/lbs torque.
The safety ground conductor provides proper grounding only for the
server. You must provide additional, proper grounding for the rack and
other devices installed in it.
Overcurrent protection: Overcurrent protection circuit breakers must
be provided as part of each host equipment rack and must be installed
between the DC source and the server. The server is designed for a
DC line voltage power source with up to 10 amperes of overcurrent
protection per feed pair. If the DC power system for the equipment rack
is installed with more than 10 amperes of protection, you must provide
supplemental protection for the server. The overall current rating of a
server configured with two power supplies is less than 7 amperes.

12 HP cc3300 Carrier Grade Server
Quick Start Guide
WARNING
Do not attempt to modify or use an AC power cord that is not the exact
type required. You must use a power cord that meets the following
criteria:
· Rating: For U.S./Canada cords must be UL Listed/CSA Certified
type SJT, 18-3 AWG. For outside U.S./Canada cords must be
flexible harmonized (<HAR>) or VDE certified cord with
3 x 0.75mm conductors rated 250 VAC.
· Connector, wall outlet end: Cords must be terminated in
grounding-type male plug designed for use in your region. The
connector must have certification marks showing certification by
an agency acceptable in your region and for U.S. must be rated
125% of overall current rating of the server.
· Connector, server end: The connectors that plug into the
AC receptacle on the server must be an IEC 320, sheet C19, type
female connector.
· Cord length and flexibility: Cords must be less than 4.5 meters
(14.76 feet) long.
NOTES
Surge Suppressor Recommendations: In geographic regions that are
susceptible to electrical storms, we highly recommend that you plug the
server into a surge suppressor.
EMI Information: For information about complying with electromagnetic
interference regulations, see “Electromagnetic Compatibility” in the HPl
cc3300 Carrier Grade ServerProduct Guide.
CAUTION
Temperature: The temperature, in which the server operates when installed
in an equipment rack, must not go below 5 °C (41 °F) or rise above 40 °C
(104 °F). Extreme fluctuations in temperature can cause a variety of
problems in your server.
Ventilation: The equipment rack must provide sufficient airflow to the front
of the server to maintain proper cooling. The rack must also include
ventilation sufficient to exhaust a maximum of 1023 BTU's per hour for the
server. The rack selected and the ventilation provided must be suitable to the
environment in which the server will be used.

HP cc3300 Carrier Grade Server 13
Quick Start Guide
Connections and Controls
Figure 2 shows the front view of the system including the front panel. The front panel contains
system control switches, alarm indicators and relays, and status indicators. Front panel controls and
LEDs are summarized in Table 2.
A Bezel H Alarm: MNR
B Peripheral Bay I Alarm: PWR
C NMI Switch J Status: NIC
D System Power Switch K Status: DSK
E System Reset L Status: ON
F Alarm: CRT M Bezel Removal Thumbscrews
G Alarm: MJR N Hard Drive Tray
Figure 2. Front Panel

14 HP cc3300 Carrier Grade Server
Quick Start Guide
Table 2. Front Panel Features
Item Feature Description
Front Panel Switches
C NMI switch A momentary switch used to instruct the processor to copy system memory to
the hard drive. Pressing the recessed button with a paper clip or pin puts the
server in a halt state for diagnostic purposes and allows you to issue a
nonmaskable interrupt. After issuing the interrupt, a memory dump can be
performed to determine the cause of the problem.
D Power switch Toggles the system power.
E Reset switch Reboots and initializes the system.
Front Panel Alarm LEDs and Relays
F Critical (amber) When continuously lit, indicates the presence of a Critical System Fault. A
critical system fault is an error or event that is detected by the system with a
fatal impact to the system. In this case, the system cannot continue to operate.
An example could be the loss of a large section of memory or other corruption
that renders the system not operational. The front panel critical alarm relay will
be engaged.
G Major (amber) When continuously lit, indicates the presence of a Major System Fault. A major
system fault is an error or event that is detected by the system that has
discernable impact to system operation. In this case, the system can continue
to operate but in a “degraded” fashion (reduced performance or loss of non-
fatal feature reduction). An example could be the loss of one of two mirrored
disks. The front panel major alarm relay will be engaged.
H Minor (amber) When continuously lit, indicates the presence of a Minor System Fault. A minor
system fault is an error or event that is detected by the system but has little
impact to actual system operation. An example would be a correctable ECC
error. The front panel minor alarm relay will be engaged.
I Power (amber) When continuously lit, indicates the presence of a Power System Fault. The
front panel power alarm relay will be engaged.
Front Panel Status LEDs
J NIC activity LED
(green)
Indicates NIC activity.
K HDD activity
LED (green)
Indicates any system SCSI hard drive activity.
L Main power
LED (green)
When continuously lit, indicates the presence of DC power in the server. The
LED goes out when the power is turned off or the power source is disrupted.
When it is blinking green, it indicates that the system is in ACPI sleep mode.

HP cc3300 Carrier Grade Server 15
Quick Start Guide
Figure 3 shows the front view of the system with the bezel removed.
OM12817
A B C
H EFG
D
A Floppy Drive E Left SCSI Drive Bay
B CD-ROM Drive F Hard Drive Tray Ribbon Cable Connector
C Front Panel Switches and LEDs G Hard Drive Tray Power Connector
D Hard Drive Tray H Right SCSI Drive Bay
Figure 3. Front View with Bezel Removed

16 HP cc3300 Carrier Grade Server
Quick Start Guide
Back Panel
Figure 4 shows the back panel view of the system.
OM12818
A C EB D
F G H I J K L
+
+
-
-
N
O
M
Figure 4. Back Panel DC Version, AC Version Shown at Right
Table 3. Back Panel Features
Item Description
A Three low profile, half-length 64-bit, 66 MHz PCI add-in board slots (3.3V riser board)
B DB-15 male connector for front panel alarm relay contacts
C Three full height, full length 64-bit, 33 MHz PCI add-in board slots (5V riser board), or,
Three full height, full length 64-bit, 66 MHz PCI add-in board slots (3.3V riser board)
D Redundant, hot-plug power supplies (AC and DC power supplies require different power supply
cages)
E Four-terminal DC input power connector for DC input power supply cage
F USB port 1
G Video connector
H External wide SCSI Ultra160†68-pin connector
I Dual NIC 10/100 E/N RJ45 connectors NIC 1 (lower) and NIC 2 (upper)
J PS/2†-compatible keyboard mouseport(requires PS/2 Y-cable to connect both keyboard and
mouse).
K Serial port (COM2), 8-pin RJ45 connector
L USB port 0
M Two ground lugs for attachment of grounding wire to chassis. Use only when configured with
DC power supply.
N and O AC input power connectors for AC input power supply cage (shown in inset)

HP cc3300 Carrier Grade Server 17
Quick Start Guide
Connecting the Monitor, Keyboard, and Mouse
CAUTION:
UNPLUG THE SERVER. Before connecting external devices, make sure
the server is not plugged in, or equipment could be damaged.
Before turning on the server, you must connect these devices to the back of the CC3300 Carrier
Grade server.
1. Connect a video monitor to the video port (G in Figure 4).
2. Connect the PS/2 Y-cable, provided with the server, to the PS/2 port (J in figure 4).
3. 3. Connect keyboard and a mouse to the PS/2 Y-cable.
Applying Power for the First Time
WARNING
The DC power source may produce hazardous voltage levels exceeding
–72 VDC and high energy levels above 240VA that may cause electric
shock or burns. All DC input connections should be made only by a
qualified service person only to prevent injury. All wiring terminals
connected to the DC input terminal block must be fully insulated with no
exposed bare metal.
The first time you turn the server on you need to enter the BIOS Setup Utility and set the correct
date and time values. After setting these values the server executes its Power-On Self Test (POST)
sequence and passes control to the Boot Manager.
For information on the Boot Manager, refer to the cc3300 Carrier Grade Server System Product
Guide.
Follow these steps to power up the cc3300 Carrier Grade server for the first time:
1. Make sure all external devices, such as a monitor, keyboard, and mouse, have been connected.
2. Plug in the AC power cord or connect the DC power wiring to the back of the chassis (M and E
in Figure 4).
3. Plug the male ends of the server AC power cords into wall outlets (grounded, three-pronged
AC power outlets).
4. Turn on the video monitor.
5. Press the Power button on the front panel (D in Figure 2). Pressing this button causes the
server fans to start up and POST to begin.
6. When POST displays the message: “Hit <F2> if you want to run SETUP,” enter <F2> and the
system will enter the BIOS Setup Utility. (If you see a prompt asking for a system password,
pressing the <ENTER> key will get you directly to the BIOS Setup Utility.)

18 HP cc3300 Carrier Grade Server
Quick Start Guide
NOTE
For information on how to use the BIOS Setup Utility, see the HP
cc3300 Carrier Grade Server Product Guide.
7. From the Main menu of the BIOS Setup Utility, use the arrow keys to move the cursor down to
the system date and time selections. Position the cursor over the date and time values and enter
appropriate values.
8. Use the <TAB> key to access the Exit menu and select the item to save changes and exit the
BIOS Setup Utility. After you exit the utility the boot procedure resumes. You can monitor the
remainder of the boot progress on the video display.

HP cc3300 Carrier Grade Server 19
Quick Start Guide
Warnings
WARNING: English (US)
AVERTISSEMENTS : Français
WARNUNG: Deutsch
AVVERTENZA: Italiano
ADVERTENCIA: Español

20 HP cc3300 Carrier Grade Server
Quick Start Guide
WARNING: English (US)
The power supply in this product contains no user-serviceable parts. There may be more
than one supply in this product. Refer servicing only to qualified personnel.
Do not attempt to modify or use the supplied AC power cord if it is not the exact type
required. A product might be equipped with more than one AC power cord.
The Power button on the system does not turn off all system power. To remove all power
from the system, you must unplug/disconnect the power cord from the system.
To avoid injury from electrical and mechanical hazards, chassis covers should only be
removed by qualified service personnel.
SAFETY STEPS: Whenever you remove the chassis covers to access the inside of the
system, follow these steps:
1. Turn off all peripheral devices connected to the system.
2. Turn off the system by pressing the Power button.
3. Unplug/disconnect the power cord from the system.
4. Label and disconnect all telecommunication cables and all other cables connected to I/O
connectors or ports on the back of the system.
5. Provide some electrostatic discharge (ESD) protection by wearing an anti-static wrist
strap attached to chassis ground of the system—any unpainted metal surface—when
handling components.
6. Do not operate the system with the chassis covers removed.
After you have completed the five SAFETY steps above, you can remove the system covers.
To do this:
1. Remove and save all screws from the covers.
2. Remove the covers.
For proper cooling and airflow, always reinstall the chassis covers before turning on the
system. Operating the system without the covers in place can damage system parts. To
install the covers:
1. Check first to make sure you have not left loose tools or parts inside the system.
2. Check that cables, add-in boards, and other components are properly installed.
3. Attach the covers to the chassis with the screws removed earlier, and tighten them
firmly.
4. Connect all external cables and the power cord to the system.
continued