HP Integrity rx4610 User manual

Version 0501
hp server rx4610
User Guide

ii
Notice
The information contained in this document is subject to change without notice.
Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to,
the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be
liable for errors contained herein or for incidental or consequential damages in connection with the furnishing,
performance, or use of this material.
Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not
furnished by Hewlett-Packard.
This document contains proprietary information that is protected by copyright. All rights are reserved. No part of
this document may be photocopied, reproduced, or translated to another language without the prior written
consent of Hewlett-Packard Company.
ATI®is a registered trademark of ATI Technologies, Incorporated. Intel® and Pentium® are registered trademarks
of Intel Corporation. Microsoft®, Windows NT®, Windows 95®, Windows 2000®and Microsoft®Internet
Explorer are registered trademarks of Microsoft in the U.S. and other countries. Netscape Navigator®is a
registered trademark of Netscape Communications Corporation in the U.S. and other countries. Symantec®is a
registered trademark of Symantec, Incorporated. pcANYWHERE32 is a trademark of Symantec, Incorporated.
Symbios®is a registered trademark of LSI Logic Corporation. Adobe®and Acrobat®are registered trademarks of
Adobe Systems Incorporated. Torx®is a registered trademark of CamCar/Textron, Incorporated.
Itanium™ is a trademark of Intel Corporation. 3M is a trademark or registered trademark of 3M.
© Copyright 2001, Hewlett-Packard Company.
Audience Assumptions
This guide is for the person who installs, administers, and troubleshoots LAN servers. Hewlett-
Packard Company assumes you are qualified in the servicing of computer equipment and trained in
recognizing hazards in products with hazardous energy levels.

iii
Contents
1Controls, Ports, and Indicators ...................................................................... 1
Introduction ........................................................................................................ 1
Front Panel .................................................................................................... 1
Additional Front Panel Controls and Indicators .............................................3
Rear View ...................................................................................................... 7
Applying Power to the HP Server .................................................................... 10
Powering-Up the HP Server ........................................................................ 10
Powering-Down the HP Server....................................................................10
Connecting AC Power to Multiple-Server Configurations............................11
2Opening and Closing the HP Server ............................................................12
Introduction ...................................................................................................... 12
Mounting the Front Bezel................................................................................. 12
Removing and Replacing the Front Bezel ....................................................... 12
Removing and Replacing the HP Server’s Main Cover..................................14
Tools Required ............................................................................................14
Removing the Top Cover.............................................................................14
Replacing the Top Cover.............................................................................15
3Installing Fans and Power Supplies ............................................................17
Introduction ...................................................................................................... 17
Tools and Supplies Needed............................................................................. 17
Hot Swapping the 172 mm Fans .....................................................................18
Removing the 172 mm Fans .......................................................................18
Installing the 172 mm Fans .........................................................................19
Hot Swapping the 120 mm Fans .....................................................................19
Removing the 120 mm Fans .......................................................................19
Installing the 120 mm Fans .........................................................................20
Hot Swapping Power Supplies ........................................................................21
Determining Power Supply Status...............................................................22
Removing a Power Supply ..........................................................................23
Installing a Power Supply ............................................................................24
4Installing Mass Storage Devices .................................................................. 25
Introduction ...................................................................................................... 25
Mass Storage Guidelines.................................................................................25
Boot Priority .................................................................................................25
Tools Required.................................................................................................26
Installing a Hot Swap Hard Drive ..................................................................... 26
Determining Drive Status............................................................................. 27
Removing a Hard Disk Drive ....................................................................... 27
Installing a Hard Disk Drive ......................................................................... 28
Installing Non-Hot Swap Drives .......................................................................29

iv
Installing the Floppy Disk Drive ................................................................... 29
Installing the DVD Drive ..............................................................................30
Connecting External SCSI Devices ............................................................. 32
Removing and Installing the Hard Disk Bay ....................................................32
Removing the Hard Disk Bay ......................................................................32
Installing the Hard Disk Bay ........................................................................33
Removing and Installing the SCSI Backplane .................................................34
Removing the SCSI Backplane ................................................................... 34
Installing the SCSI Backplane Board........................................................... 34
Installing the Front Panel Board ......................................................................35
Removing the Front Panel Module .............................................................. 35
Installing the Front Panel Board ..................................................................35
5Installing Additional Memory........................................................................36
Introduction ...................................................................................................... 36
Tools Required ............................................................................................36
Memory Installation Guidelines ................................................................... 36
Removing the Processor/Memory Complex ....................................................37
Removing the Memory Board DC-to-DC Converters ......................................38
Removing and Installing Memory Boards ........................................................ 39
Removing Memory Boards .......................................................................... 39
Installing Memory Boards ............................................................................40
Installing and Removing DIMMs ......................................................................42
Installing DIMMs ..........................................................................................42
Removing DIMMs ........................................................................................44
Installing the Memory Board DC-to-DC Converters ........................................44
Installing the Processor/Memory Complex ...................................................... 45
6Installing an Additional Processor...............................................................46
Introduction ...................................................................................................... 46
Tools Required ............................................................................................46
Processor Configuration Guidelines ............................................................ 46
Removing the CPU Thermal Dummy ..............................................................47
Installing an Additional Processor....................................................................48
Removing a Processor.....................................................................................51
Installing a CPU Thermal Dummy ...................................................................52
Installing the Processor Baseboard .................................................................52
Removing the Processor Baseboard...........................................................53
Installing the Board in a System with Three or Four Microprocessors........ 54
Installing the Board in a System with Two Microprocessors .......................55
7Installing Accessory Boards ........................................................................57
Introduction ...................................................................................................... 57
Tested PCI Boards ......................................................................................57
Tools Required ............................................................................................57
Accessory Board Installation Guidelines ......................................................... 57
IRQ Settings ................................................................................................ 57

v
Boot Priority .................................................................................................58
Installing Accessory Boards............................................................................. 58
Installing a Hot Swap PCI Board ................................................................. 58
Installing a Non-Hot Plug PCI Board ........................................................... 60
Removing Accessory Boards...........................................................................63
Removing a Non-Hot Plug PCI Board ......................................................... 63
Removing a Hot Plug PCI Board ................................................................. 64
8Server Management Boards ......................................................................... 65
Introduction ...................................................................................................... 65
Baseboard Management Controller (BMC) .................................................65
Intelligent Chassis Management Bus (ICMB) Controller .............................66
Hot Swap Controller (HSC) .........................................................................66
I/O Baseboard ..................................................................................................68
Removing the I/O Baseboard ......................................................................68
Installing the I/O Baseboard ........................................................................ 70
Sideplane Board .............................................................................................. 71
Removing the Sideplane Board...................................................................71
Installing the Sideplane Board.....................................................................72
PCI Hot Plug LED Board..................................................................................72
Removing the PCI Hot Plug LED Board...................................................... 72
Installing the PCI Hot Plug LED Board ........................................................73
Legacy I/O Board .............................................................................................74
Removing the Legacy I/O Board .................................................................74
Installing the Legacy I/O Board ...................................................................75
Changing the Legacy I/O Board Battery.......................................................... 77
Power Distribution Board (T-Docking) .............................................................78
Removing the Power Distribution Board (T-Docking).................................. 78
Installing the Power Distribution Board (T-Docking).................................... 82
9Connecting the Monitor, Keyboard, and Mouse......................................... 84
Introduction ...................................................................................................... 84
10 Configuring the HP Server........................................................................... 86
Introduction ...................................................................................................... 86
Configuring the HP Server ...............................................................................86
Power-on Sequence and Power-on Self Test (POST)................................ 86
The Extensible Firmware Interface (EFI) Boot Manager .............................87
Server Management Configuration Utility....................................................92
Using BIOS Setup........................................................................................ 99
Using the SELViewer Utility....................................................................... 107
Using the SDR Viewer Utility .....................................................................112
Server Firmware ............................................................................................115
11 Troubleshooting..........................................................................................116
Introduction .................................................................................................... 116
Common Installation Problems......................................................................116
Troubleshooting Sequence........................................................................ 116

vi
HP Server rx4610 SEL Data Tables ..............................................................120
HP Server rx4610 Sensor Codes ..............................................................121
BIOS Error Codes\Messages ........................................................................125
Beep Codes ................................................................................................... 129
Beep Codes and Interpretation.................................................................. 129
Types of Memory Tests .................................................................................131
First Row Memory Test..............................................................................131
Base Memory Test..................................................................................... 134
Extended Memory Test ............................................................................. 140
Memory Test Duration ...............................................................................143
Aborting the Memory Test .........................................................................144
Setup Dialog ..............................................................................................145
Memory Testing Error Codes\Messages ...................................................145
DIMMUTIL ................................................................................................. 148
12 Parts Information.........................................................................................149
Exploded View – Hot Swap and Display........................................................149
Exploded View – Processor/Memory Access ................................................150
Exploded View – Processor/Memory Complex.............................................. 151
Exploded View – Server Management Boards.............................................. 153
Exploded View – Power Distribution Board and IDE Drives.......................... 154
Replaceable Parts List ...................................................................................155
Parts List Identifier .........................................................................................155
Appendix A Specifications ......................................................................... 158
Introduction .................................................................................................... 158
Requirements ............................................................................................158
Video Display Modes ................................................................................. 160
Connector Pinouts and Boardset Locations ..................................................161
VGA Video Port .........................................................................................161
Keyboard and Mouse................................................................................. 162
Parallel Port ...............................................................................................163
Serial Ports A and B .................................................................................. 163
Universal Serial Bus (USB) .......................................................................165
SCSI ..........................................................................................................166
IDE............................................................................................................. 167
PCI ............................................................................................................. 168
Information on Jumpers ................................................................................. 171
General Procedure to Change Jumper Settings .......................................171
Processor Baseboard Jumpers .................................................................171
Legacy I/O Board Jumpers........................................................................177
I/O Baseboard Jumpers............................................................................. 181
Power Distribution Board Jumpers (T-Docking) ........................................ 183
Determining DC-to-DC Status ...................................................................184
BEquipment Log and Configuration Worksheet ......................................... 186
Equipment Log...............................................................................................186

vii
Index ..................................................................................................................188

Chapter 1: Controls, Ports, and Indicators
1
1 Controls, Ports, and Indicators
Introduction
Before operating the Server, familiarize yourself with the HP Server’s controls, ports, and indicators,
as shown in Figures 1-1 through 1-8.
Front Panel
The front panel of the HP Server provides the controls and indicators commonly used when operating
the HP Server.
LCD DISPLAY
POWER
PWR PWR ACTIVEACTIVE FAIL FAIL
RESET INT SYS PWR PWR FAN GEN
Figure 1-1. Front Panel
Table 1-1 provides the front panel power switch and its associated LED indicator definitions.

Chapter 1: Controls, Ports, and Indicators
2
Table 1-1. Control Panel Switch and Indicators
Control / Indicator Description
Power On/Off
This button turns the HP Server power On or Off. The
+12 V standby voltage is On whenever the server power
cords are plugged in.
Reset
When pressed, it resets the server and causes the power on
self-test (POST) to run.
INIT
When pressed, the system performs a crash dump provided
the dump is supported by the operating system.
System Power LED
(Green)
When lit continuously, it indicates the presence of DC
power in the server. When not lit, it indicates power is
turned off or the power source is disrupted.
Power Fail LED
(Amber)
When lit continuously, it indicates a power failure.
Fan Fail LED (Amber) When flashing, it indicates a fan failure.
General Fault LED
(Amber)
When lit continuously, it indicates a hot plug PCI fault.
Front Panel LCD It displays information about the processor type and the
POST codes.

Chapter 1: Controls, Ports, and Indicators
3
Additional Front Panel Controls and Indicators
The input and storage devices provide additional front panel controls and indicators, which give
control and operational status to the respective device.
DVD Drive
The server supports a slimline IDE DVD drive. This peripheral mounts directly above the top-left
power bay on the front of the chassis. The drive is mounted on a removable tray that facilitates
system assembly and service.
LCD DISPLAY
POWER
PWR PWR ACTIVEAC TIV E FAI L FAI L
RESET INT SYS PWR PWR FAN GEN
Open/Close Button
A
ctivity LED
Figure 1-2. DVD Drive
Table 1-2. HP DVD Drive
Control Indicator Description
Open/Close Button When pressed, it opens or closes the DVD tray.
Activity LED When lit, it indicates the drive is in use.

Chapter 1: Controls, Ports, and Indicators
4
Diskette Floppy Drive
The server supports a slimline IDE diskette drive for 1.44 MB and 120 MB media. This half-inch
slimline peripheral mounts directly above the top-right power bay on the front of the chassis. The
drive is mounted on a removable tray that facilitates system assembly and service.
LCD DISPLAY
POWER
PWR PWR ACTIVEAC TIV E FAI L FA IL
RESET INT SYS PWR PWR FAN GEN
A
ctivity
LED Ejector
Button
Figure 1-3. Drive
Table 1-3. Floppy Diskette Drive
Control Indicator Description
Activity LED When lit, it indicates the drive is in use.
Ejector Button When pressed, it ejects the diskette.

Chapter 1: Controls, Ports, and Indicators
5
SCSI Hard Drives
The server supports up to two hot-swap drive carriers containing standard 1-inch high by 3.5-inch-
wide LVDS SCSI hard drives. As part of the hot-swap implementation, drive carriers with integral
heat sinks house the drives. Each drive is mounted in a carrier with four fasteners and the carrier
snaps into the hard drive bay. When a carrier is seated properly in the bay, it snaps into place and
leaves the locking handle exposed to the front of the chassis. Drives can consume up to 24 watts of
power and must be specified to run at a maximum ambient temperature of 40 °C (104 °F).
LCD DISPLAY
POWER
PWR PWR ACTIVEACTIVE FAIL FAIL
RESET INT SYSPW R PWR F AN GEN
LCD DISPLAY
PO W E R
PW R PW R ACT IVEACT IVE FAIL FA IL
RES ET INT SY S PW R PW R FAN GEN
Power LED
Drive Active
Failure LED Power LED
Drive Active
Failure LED
Figure 1-4. SCSI Drive Indicators on the Front LED Panel
Table 1-4. SCSI Drives
Control Indicator Description
Drive Power LED
(Green)
When lit continuously, it indicates the presence of
the drive and power to the drive.
Drive Active LED
(Green)
When lit, it indicates drive activity.
Drive Fail LED
(Amber)
When lit continuously, it indicates an asserted fault
status on one or more hard disk drives. When
flashing, it indicates a drive reset in progress.

Chapter 1: Controls, Ports, and Indicators
6
Power Supplies
The chassis can be configured with three to four power supplies. Each power supply has a dual rating
of 800W minimum over an input range of 180-264VAC and 700W minimum over an input range of
90-132VAC. Each supply is designed to minimize EMI and RFI. Each power supply also has self-
contained fans for cooling.
The DC output voltages of each power supply are:
•+48 V
•+12 V standby
Each supply docks into a 28-pin connector on the front of the Power Distribution Board (T-Docking
board).
LCD DISPLAY
POWER
PWR PWR ACTIVEACT IVE FAIL FAI L
RESET INT SYS PWR PWR FAN GEN
Power Supply Indicators
Figure 1-5. Power Supply Indicators
Table 1-5. LEDs for Power Supplies
Control Indicator Description
Power LED
(Green)
When lit continuously, it indicates the power
supply DC outputs are on and OK. Blinking
indicates the power supply is on standby. Off
indicates there is no power to the power supply.
Predictive Fail LED
(Amber)
A blinking LED indicates that the power supply
will soon fail.
Fail LED
(Amber)
When lit continuously, it indicates that the power
supply has failed and is not supplying output.
When blinking, it indicates that the power supply
has reached its current limit.

Chapter 1: Controls, Ports, and Indicators
7
Rear View
The ports and connectors at the rear are listed below and shown in Figure 1-6. Figure 1-6 provides a
detailed view of the Legacy I/O panel that resides in the upper-right corner of the rear panel.
•The power connector accepts a standard power cable to connect the
HP Server with the site power supply.
•Ten PCI add-in board expansion slots are available. Eight are hot plug and two are non-hot
plug.
•Each hot plug PCI has status LEDs.
•The mouse port accepts a standard mouse with a PS/2 connector.
•The keyboard port accepts a standard keyboard with a 6-pin PS/2 connector.
•Two USB ports, 0 and 1, with 4 pin connectors are provided for printers, scanners, and
external modems.
•The LAN port is included as an embedded controller based on Intel's 82559 10/100 BaseT Fast
Ethernet controller. It has a RJ-45 LAN connector and two LEDs to indicate LAN speed and
valid connection.
•The two Serial Ports are standard 9-pin RS-232 connectors.
•The Parallel Port is a standard PS/2 compatible parallel port with a 25 pin bi-directional
subminiature D connector.
•There are two Interchassis Management Bus (ICMB) connectors, ports 1 and 2.
•The 15 pin video connector is Super VGA compatible.
•The optional external SCSI port provides access to external SCSI devices.
Figure 1-6. Rear Panel and Ports

Chapter 1: Controls, Ports, and Indicators
8
Legacy I/O Panel
This board contains all legacy I/O connections and plugs into an edge connector on the I/O baseboard.
NOTE The keyboard and mouse connector must be plugged into the correct ports or the
server will not boot.

Chapter 1: Controls, Ports, and Indicators
9
PCI LEDs
Each PCI slot has four indicator LEDs: two on the outside and two on the inside of the system. The
two LEDs for each slot: one amber and one green are visible from the rear (also inside) of the HP
Server, as shown in Figure 1-7. Eight of the ten PCI slots can be individually powered down through
the respective NOS or supported GUI utility, without powering down the entire HP Server, if the
board has a Hot Plug compliant driver.
Status Indicators for PCI Cards
Figure 1-7. Status Indicators for PCI Boards

Chapter 1: Controls, Ports, and Indicators
10
Applying Power to the HP Server
Before applying power to the HP Server, verify that the keyboard and mouse are connected to the
proper ports. The server will not boot without these devices. Turning on the monitor prior to
powering on the HP Server allows proper auto-configuration of the video output as it boots.
Powering-Up the HP Server
To power-up the rx4610, complete the following procedure:
NOTE Turn on power to the monitor connected to the HP Server before you power-on the
Server. This allows proper
auto-configuration of video output of the Server as it boots.
1. Make sure that the monitor, keyboard, and mouse have been connected to the proper ports on
the rear panel of the server.
2. Remove the drive protection card, if present, from the diskette drive.
3. Plug in the power cord for the monitor and turn it on.
4. Plug the female ends of the server AC power cords into the input receptacle on the back of the
chassis.
5. Plug the male ends of the server AC power cords into grounded,
three-pronged AC power outlet.
6. Slide the server into the rack.
7. If the server does not come on when you plug it into the AC outlet, press the on/off power
switch on the front panel.
8. Verify that the power-on light on the front panel is lit. After a few seconds, the power-on self
test (POST) begins.
When you press the power button on the control panel, the Server powers up and loads the
operating system. The system runs a set of power on self tests (POST) during this process. For
details refer to Chapter 11, "Troubleshooting."
Powering-Down the HP Server
To power-down the HP Server, complete the following procedure:
1. Log off all users and, if necessary, back up the system files.
◊ Schedule the power down for a time when the Server being down will affect the fewest
users.
◊ If you will be doing any kind of hardware or software upgrade, ensure the Server's data has
been backed up.
◊ Follow instructions in your network operating system (NOS) documentation to gracefully
shut down all networking software and applications.
WARNING The power supply will continue to provide standby current to the HP Server until
the power cable is disconnected from the rear panel.

Chapter 1: Controls, Ports, and Indicators
11
2. Logoff and exit the operating system. The following prompt appears:
Shell>
3. At the Shell> prompt, press and hold the Power button for several seconds. Holding the Power
button in for several seconds will power down the server.
4. Disconnect the power cords from the power source.
Normally this completes the power-down procedure.
Connecting AC Power to Multiple-Server Configurations
The HP Server temporarily draws a large "inrush current," when first connected to an AC power
source. This also occurs when the Server is in a standby mode (power is turned off, but the power
cord is plugged into AC power). The inrush current is much greater than the Server's normal operating
current and generally, the AC power source can handle the normal inrush current.
However, if you install several HP Servers on one circuit, precautions are necessary. If there is a
power failure and power is then restored, all the servers immediately begin to draw inrush current at
the same time. If the circuit breakers on the incoming power line have insufficient capability, the
breaker may trip and thus prevent the servers from powering up.

12
2 Opening and Closing the HP Server
Introduction
This chapter describes how to remove and replace the front bezel and the HP Server's main cover.
Mounting the Front Bezel
The front handles, if not already installed on the HP Server, should be attached to the front of the HP
Server before mounting the bezel.
1. Place the handles into the slots on the front of the HP Server on each edge, as shown in the
figure below.
2. Insert the screws through the bracket into the top hole of each group of three holes on the front
sides of the HP Server. Repeat this procedure for both handles.
3. Hold the bezel in front of the HP Server.
4. Press the bezel firmly into place.
You should hear several clicks as the bezel snaps into place on the bracket.
Removing and Replacing the Front Bezel
The bezel is packed in the top tray.
1. To remove the bezel, pull it straightforward off the chassis.
This exposes the power supplies, mass storage devices, and fans.
2. To replace the bezel, press it back onto the chassis, allowing it to snap into place. See Figure
2-1.

Chapter 2: Opening and Closing the HP Server
13
Figure 2-1. Removing and Replacing the Front Bezel