HP ProLiant ML110 - G2 Server Assembly instructions

HP ProLiant ML110
Generation 2 Server
Installation Sheet
Read instructions completely before beginning
installation procedure.
© Copyright January 2005 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only
warranties for HP products and services are set forth in the express warranty
statements accompanying such products and services. Nothing herein should be
construed as constituting an additional warranty. HP shall not be liable for technical
or editorial errors or omissions contained herein.
Intel and Pentium are trademarks or registered trademarks of Intel Corporation or its
subsidiaries in the United States and other countries.
HP ProLiant ML110 Generation 2 Server Installation Sheet
First Edition (January 2005)
Part Number 375600-001
375600- 001
Configuring the Server
1. Connect all peripherals:
—Keyboard
—Mouse
—Monitor
NOTE: Refer to the HP ProLiant ML110 Generation 2 Server Support CD.
Refer to the CD contents for additional information and updates not
provided in this installation sheet.
2. Determine the server BIOS version:
a. Power up the server.
b. Press the Esc key at the HP logo screen, then press the
Pause key to halt screen movement.
c. Note the server BIOS version.
d. Verify the server BIOS version against the latest BIOS
version listed for this server on the HP website:
http://www.hp.com
e. If you do not have the latest BIOS, update the BIOS now.
Refer to the HP ProLiant ML110 Generation 2 Server
Maintenance and Service Guide available on the HP
website: http://www.hp.com
Default Boot Priority
By default, the server searches for boot devices in the following
order:
1. Removable device
2. IDE CD-ROM drive
3. Hard disk drive
4. PXE IBA GE slot 0A08 V1219
Identifying Server Components
Front Panel Components
Table 1: Front Panel Components
Item Description
1 CD-ROM drive
2 CD-ROM drive mechanical eject hole
3 CD-ROM drive eject button
4 CD-ROM drive activity indicator
5 Full-height common bays
6 Dual-color status LED indicator
•Green – Power indicator
•Amber – System health indicator
continued

Table 1: Front Panel Components continued
Item Description
7Power button
8 Drive activity indicator (amber)
9 Front USB 2.0 ports
10 Hard disk drive (HDD) cage
11 Torx screws for the HDD cage
Rear Panel Components
Table 2: Rear Panel Components
Item Description
1 PS/2 mouse port (green)
2 PS/2 keyboard port (purple)
3 Serial port (teal)
4 Parallel port (burgundy)
5 Monitor port (blue)
6 Rear USB 2.0 ports (black)
7 LAN port (RJ-45)
8 PCI slot covers
9 PSU fan
10 Power supply cable socket
11 Thumbscrews for the access panel
12 System fan
13 Retention clips for the PCI slot covers
14 Kensington lock notch
System Board Components
Table 3: System Board Components
Item Code Description
1 CN1 Top: PS/2 mouse port (green)
Bottom: PS/2 keyboard port (purple)
2 CN2 Top: Parallel port (burgundy)
Left: Monitor port (blue)
Right: Serial port (teal)
3 CN5 USB 2.0 ports (black, two)
4 CN6 LAN port (RJ-45)
5 CN7 3-pin CPU fan connector
6 CN10 3-pin system fan connector (rear)
7 PCI1 to
PCI3
64-bit/100 MHz 3.3V PCI-X bus slots
(three)
8 U13 Intel GD8254IPI GbE LAN controller
9 U17 SMSC LPC47M192 Super I/O chipset
10 U18 VGA frame buffer
11 PCI4 PCI-Express x4 bus slot
12 U22 ATI Rage XL VGA chipset
13 PCI5 32-bit/33 MHz 5V PCI bus slot
14 CN22 9-pin BMC COM connector
15 CN24 9-pin extension serial connector (COM2)
16 CN20 IPMI connector
17 U34 BIOS
18 CN21 9-pin front USB connector
19 CN27 Internal USB connector
20 CN17 Internal USB connector (for internal USB
tape use)
21 CN18 34-pin FDD connector
22 CN13 4-pin SCSI LED connector
23 CN16 9-pin front panel connector
24 SATA0 –
SATA3
7-pin 150-MBps SATA connectors (four)
25 BZ1 Internal buzzer
26 IDE1 IDE channel UDMA-100
27 SW1 System configuration switch (dip switch)
28 U46 Intel ICH6R chipset (south bridge)
29 JP1 PCI-X bus speed jumper
Jumper setting:
•1-2 – 133 MHz PCI-X bus (default)
•2-3 – 100 MHz PCI-X bus
30 BT1 Battery
31 U16 Intel6702 PXH-V chipset (PCI bridge)
32 U9 Intel E7220 chipset (north bridge)
33 U10 Intel LGA775 CPU socket
34 DIMM1 to
DIMM4
DIMM slots (four)
35 PWRCON2 20-pin ATX system board power
connector
36 PWRCON1 4-pin ATX CPU power connector

Opening the Server
The access panel and the front bezel are both detachable. You need
to remove these system covers before you can remove or replace a
server component.
Removing the Access Panel
Removing the Front Bezel
Installing Mass Storage Devices
The lower drive bay on the front panel accommodates an HDD
cage for installation of up to four additional hard drives. The
hot-plug HDD cage model supports SATA drives only, while the
non-hot-plug model supports both SATA and SCSI drives.
CAUTION: Drives can be damaged by static electricity. Before
handling drives, touch an unpainted metal surface to discharge
static electricity.
WARNING: If you are going to install a non-hot-plug drive,
power down the server first.
Non-hot-plug SCSI Drives
Non-hot-plug SATA Drives

Hot-plug SATA Drives
Installing the PCI Accessory Board
The HP ProLiant ML110 Generation 2 server supports five PCI
bus slots.
•Three 64-bit/100-MHz 3.3V PCI-X bus slots (PCI1 to PCI3)
•One PCI-Express x4 bus slot (PCI4)
•One 32-bit/33-MHz 5VPCI bus slot (PCI5)
Installing Memory
The HP ProLiant ML110 Generation2 server has four DIMM slots
that support up to 4 GB maximum system memory(1 GB in
each of the four DIMM slots).
The following guidelines must be followed when memory
modules are being added or replaced:
•Use only DDR 400 unbuffered ECC and non-ECC DIMMs in
256 MB, 512 MB, or1 GB configuration.
•Up to two DIMMs per channel, single-sided and/or
double-sided. Channel A corresponds to the DIMM1 and
DIMM2 slots, while channel B corresponds to the DIMM3 and
DIMM4 slots.
CAUTION: DIMMs can be damaged by improper handling.
Always use an anti-static wrist strap and grounding mat, and
discharge static electricitybefore touching DIMMs.
The DIMM slots are structuredto ensure proper installation. If you
insert a DIMM but it does not fit easily into the slot, you may have
inserted it incorrectly. Reverse the orientation of the DIMM and
insert it again.
Replacing the Processor
The LGA775 CPU socket in the HP ProLiantML110 Generation 2
server supports an Intel® Pentium®4 processor.
Obtaining Additional
Documentation
For additional documentation, refer to the HPProLiant ML110
Generation 2 Server Support CD. You can also access additional
information and documentation fromthe HP website, www.hp.com
either by connecting directly or through the SupportCD.