HP t150 Operating and maintenance manual

Hardware Reference Guide
HP MultiSeat Thin Client t150

© Copyright 2010 Hewlett-Packard
Development Company, L.P. The information
contained herein is subject to change
without notice.
Microsoft and Windows are trademarks of
Microsoft Corporation in the U.S. and other
countries.
The only warranties for HP products and
services are set forth in the express warranty
statements accompanying such products and
services. Nothing herein should be
construed as constituting an additional
warranty. HP shall not be liable for technical
or editorial errors or omissions contained
herein.
This document contains proprietary
information that is protected by copyright.
No part of this document may be
photocopied, reproduced, or translated to
another language without the prior written
consent of Hewlett-Packard Company.
Hardware Reference Guide
HP MultiSeat Thin Client t150
First Edition (November 2010)
Document Part Number: 641566–001

About This Book
WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily
harm or loss of life.
CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage
to equipment or loss of information.
NOTE: Text set off in this manner provides important supplemental information.
iii

iv About This Book

Table of contents
1 Front Panel Components ................................................................................................... 1
2 Rear Panel Components .................................................................................................... 2
3 Serial Number Location .................................................................................................... 3
Appendix A Specifications ................................................................................................... 4
Appendix B Security Provisions ............................................................................................ 6
HP MultiSeat Thin Client t150 Security Clip ................................................................................. 6
Securing the HP MultiSeat Thin Client t150 .................................................................. 6
Securing the HP MultiSeat Thin Client t150 in the Mounting Bracket ................................ 7
Cable Lock .............................................................................................................................. 8
Appendix C Mounting the HP MultiSeat Thin Client t150 ....................................................... 9
Mounting Bracket ..................................................................................................................... 9
Attaching the HP MultiSeat Thin Client t150 to the Mounting Bracket ............................... 9
Releasing the HP MultiSeat Thin Client t150 from the Mounting Bracket ......................... 10
Supported Mounting Options ................................................................................................... 11
Non-supported Mounting Option ............................................................................................. 13
Appendix D HP MultiSeat Thin Client t150 Operation ......................................................... 14
Routine HP MultiSeat Thin Client t150 Care ............................................................................... 14
Supported Orientations ........................................................................................................... 14
Non-supported Orientation ...................................................................................................... 16
Appendix E Electrostatic Discharge ..................................................................................... 17
Preventing Electrostatic Damage .............................................................................................. 17
Grounding Methods ............................................................................................................... 17
v

Appendix F Shipping Information ...................................................................................... 18
Shipping Preparation .............................................................................................................. 18
Important Service Repair Information ........................................................................................ 18
Index ................................................................................................................................. 19
vi

1 Front Panel Components
For more information, http://www.hp.com and search for your specific HP MultiSeat Thin Client t150
model to find the model-specific QuickSpecs.
Figure 1-1 Front panel components
(1) Power LED (4) PS/2 connectors (2)
(2) Line-out (headphone) audio connector (5) USB 2.0 connectors (2)
NOTE: If the optional DC adapter is not
connected, the HP MultiSeat Thin Client t150
supports only one 100 mA USB device (low power),
such as a flash drive.
If the optional DC adapter is connected to a working
power outlet or to the monitor, the t150 supports two
500 mA (high power) USB devices.
The HP LE1851w 18-inch Widescreen LCD Monitor
is the only HP monitor that can supply power to the
t150.
(3) Line-in (microphone) connector
1

2 Rear Panel Components
For more information, http://www.hp.com and search for your specific HP MultiSeat Thin Client t150
model to find the model-specific QuickSpecs.
Figure 2-1 Rear panel components
(1) Cable lock slot (4) USB PC power connector to host PC (USB Type A/B
cable included)
(2) DC power connector (5) Security clip slot
(3) VGA connector
2 Chapter 2 Rear Panel Components

3 Serial Number Location
Figure 3-1 Serial number location
Every HP MultiSeat Thin Client t150 includes a unique serial number located as shown in the following
illustration. Have this number available when contacting HP customer service for assistance.
3

A Specifications
Table A-1 HP MultiSeat Thin Client t150
Dimensions
Width (side to side)
Height (without mounting bracket)
Height (with mounting bracket)
Depth (front to back)
111.7 mm
28.2 mm
34.8 mm
65.0 mm
4.40 in.
1.11 in
1.38 in
2.56 in.
Approximate Weight
Without mounting bracket
With mounting bracket
135.7 g
162.0 g
4.78 oz
5.71 oz
Temperature Range *
Operating**
(max. rate of change is 10° C per hour or 18° F per hour)
Nonoperating
(max. rate of change is 20° C per hour or 36° F per hour)
10° to 40° C
-30° to 60° C
50° to 104° F
-22° to 140° F
*Specifications are at sea level with altitude derating of
1° C/300m (1.8° F/1000ft) to a maximum of 3Km
(10,000ft), with no direct, sustained sunlight. Upper limit
may be limited by the type and number of options installed.
** The operating temperature range when the HP
MultiSeat Thin Client t150 is attached to a flat panel
using the mounting bracket is 50° to 95° F (10° to 35°
C).
4 Appendix A Specifications

Table A-1 HP MultiSeat Thin Client t150 (continued)
Relative Humidity (non-condensing)
Operating
(max. wet bulb temperature is 28° C or 84.2° F)
Nonoperating
(max. wet bulb temperature is 38.7° C or 101.6° F)
10–90%
5–95%
10–90%
5–95%
Maximum Altitude (unpressurized)
Operating
(max. allowed rate of change is 457 m per minute or 1500
ft per minute)
Nonoperating
(max. allowed rate of change is 457 m per minute or 1500
ft per minute)
3,048 m
9,144 m
10,000 ft
30,000 ft
5

B Security Provisions
HP MultiSeat Thin Client t150 Security Clip
The HP MultiSeat Thin Client t150 ships with a security clip which can be fastened to the rear panel of
the HP MultiSeat Thin Client t150. To prevent unauthorized removal of the HP MultiSeat Thin Client
t150, fasten a padlock through the clip and a cable.
Securing the HP MultiSeat Thin Client t150
Figure B-1 Securing the HP MultiSeat Thin Client t150
1. With the tab of the HP MultiSeat Thin Client t150 security clip pointing up, insert the HP MultiSeat
Thin Client t150 security clip between the guides on the back of the HP MultiSeat Thin Client t150
(1). Use the provided screw to fasten the security clip to the HP MultiSeat Thin Client t150 (2).
2. Insert a padlock through the loops of the security clip (3) and a cable.
6 Appendix B Security Provisions

Securing the HP MultiSeat Thin Client t150 in the Mounting Bracket
Figure B-2 Securing the HP MultiSeat Thin Client t150 in the mounting bracket
1. With the tab of the HP MultiSeat Thin Client t150 security clip pointing down, insert the HP
MultiSeat Thin Client t150 security clip between the guides on the back of the HP MultiSeat Thin
Client t150 into the slot on the back of the mounting bracket (1). Use the provided screw to fasten
the security clip to the HP MultiSeat Thin Client t150 (2).
2. Insert a padlock through the loops of the security clip (3) and lock it to prevent access to the
security clip screw.
HP MultiSeat Thin Client t150 Security Clip 7

Cable Lock
The HP MultiSeat Thin Client t150 is designed to accept a security cable lock. This cable lock prevents
unauthorized removal of the HP MultiSeat Thin Client t150. To order this option, visit the HP Web site
at http://www.hp.com and search for your specific HP MultiSeat Thin Client t150 model.
Figure B-3 Securing the HP MultiSeat Thin Client t150
1. Locate the cable lock slot on the back panel.
2. Insert the cable lock into the slot, and then use the key to lock it.
8 Appendix B Security Provisions

C Mounting the HP MultiSeat Thin
Client t150
Before mounting the HP MultiSeat Thin Client t150, be sure to attach the mounting bracket. See
Mounting Bracket on page 9for more information.
Mounting Bracket
The HP MultiSeat Thin Client t150 ships with a mounting bracket which should be used to secure the HP
MultiSeat Thin Client t150 to various mounting solutions. The bracket incorporates four mounting points
on one side of the unit. These mounting points follow the VESA (Video Electronics Standards
Association) standard, which provides industry-standard mounting interfaces for Flat Displays (FDs),
such as flat panel monitors, flat displays, and flat TVs.
Attaching the HP MultiSeat Thin Client t150 to the Mounting
Bracket
1. Attach the mounting bracket to a supported mounting solution. See Supported Mounting Options
on page 11 for more information.
Figure C-1 Inserting the HP MultiSeat Thin Client t150 into the mounting bracket
2. Hold the HP MultiSeat Thin Client t150 so that the bottom of the unit will be next to the Mounting
Bracket and slide the HP MultiSeat Thin Client t150 front-first into the bracket.
3. Secure the HP MultiSeat Thin Client t150 to the mounting bracket. See Securing the HP MultiSeat
Thin Client t150 in the Mounting Bracket on page 7
Mounting Bracket 9

Releasing the HP MultiSeat Thin Client t150 from the Mounting
Bracket
Figure C-2 Removing the security clip
1. If there is a lock through the HP MultiSeat Thin Client t150 security clip on the back of the HP
MultiSeat Thin Client t150 , unlock and remove it (1).
2. Remove the screw holding the HP MultiSeat Thin Client t150 security clip (2) and remove the
security clip from the back of the mounting bracket (3).
Figure C-3 Removing the mounting bracket
3. Press the bracket lever away from the HP MultiSeat Thin Client t150 (1) and slide the unit out of
the mounting bracket (2).
10 Appendix C Mounting the HP MultiSeat Thin Client t150

Supported Mounting Options
The following illustrations demonstrate some of the supported and not supported mounting options for
the mounting bracket.
●You can mount the HP MultiSeat Thin Client t150 in the mounting bracket on the back of a flat
panel monitor stand.
Figure C-4 HP MultiSeat Thin Client t150 mounted on back of monitor stand
●You can mount the HP MultiSeat Thin Client t150 in the mounting bracket on the back of a flat
panel monitor, if you have VESA holes available.
Figure C-5 HP MultiSeat Thin Client t150 mounted on back of monitor
●You can mount the HP MultiSeat Thin Client t150 in the mounting bracket on a wall.
Supported Mounting Options 11

Figure C-6 HP MultiSeat Thin Client t150 mounted on wall
●You can mount the HP MultiSeat Thin Client t150 in the mounting bracket under a desk.
Figure C-7 HP MultiSeat Thin Client t150 mounted under desk
12 Appendix C Mounting the HP MultiSeat Thin Client t150

Non-supported Mounting Option
CAUTION: Mounting the HP MultiSeat Thin Client t150 in an non-supported manner could result in
failure of the mounting bracket and damage to the HP MultiSeat Thin Client t150 and/or other
equipment.
Do not mount the HP MultiSeat Thin Client t150 on a flat panel monitor stand, between the panel and
the stand.
Figure C-8 Unsupported mounting position—HP MultiSeat Thin Client t150 between stand and
monitor
Non-supported Mounting Option 13

D HP MultiSeat Thin Client t150
Operation
Routine HP MultiSeat Thin Client t150 Care
Use the following information to properly care for the HP MultiSeat Thin Client t150:
●Never operate the HP MultiSeat Thin Client t150 with the outside panel removed.
●Keep the HP MultiSeat Thin Client t150 away from excessive moisture, direct sunlight, and
extreme heat and cold. For information about the recommended temperature and humidity ranges
for the HP MultiSeat Thin Client t150, see Specifications on page 4.
●Keep liquids away from the HP MultiSeat Thin Client t150.
●Turn off the HP MultiSeat Thin Client t150 and wipe the exterior with a soft, damp cloth as
needed. Using cleaning products may discolor or damage the finish.
Supported Orientations
HP supports the following orientations for the HP MultiSeat Thin Client t150.
CAUTION: You must adhere to HP-supported orientations to ensure your HP MultiSeat Thin Client
t150 functions properly.
●If the HP MultiSeat Thin Client t150 is not to be mounted, only the horizontal orientation is
supported. Be sure to set the HP MultiSeat Thin Client t150 on its rubber feet.
14 Appendix D HP MultiSeat Thin Client t150 Operation