HP D7171A - NetServer - LPr User manual

HP NetServer LXr 8500
PCI Hot Plug Utility
User Guide
Printed in August 1999

ii
Notice
The information contained in this document is subject to change without notice.
Hewlett-Packard makes no warranty of any kind with regard to this material, including, but
not limited to, the implied warranties of merchantability and fitness for a particular
purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of this
material. Hewlett-Packard assumes no responsibility for the use or reliability of its software
on equipment that is not furnished by Hewlett-Packard.
This document contains proprietary information that is protected by copyright. All rights
are reserved. No part of this document may be photocopied, reproduced, or translated to
another language without the prior written consent of Hewlett-Packard Company.
The use of trademarks or other designations is for reference purposes only. The following
trademarks are used in this manual:
Intel and Pentium are registered trademarks of Intel Corporation. Microsoft and MS-DOS
are U.S. registered trademarks of Microsoft Corp. Windows and Windows NT are
trademarks of Microsoft Corp. Novell, NetWare, and IntranetWare are registered
trademarks of Novell, Inc.
Hewlett-Packard Company
Network Server Division
Technical Communications / MS 45SLE
10955 Tantau Avenue
Cupertino, CA 95014-0770, USA
© Copyright 1999, Hewlett-Packard Company

iii
Contents
1 PCI Hot Plug Utility for Windows NT ............................................................. 1
Opening the Hot Plug Utility .............................................................................. 1
Opening the PCI Hot Plug Utility ....................................................................... 2
Powering Down a PCI Slot ................................................................................ 5
Removing a Hot Plug Board .............................................................................. 8
Powering Up a PCI Slot ................................................................................... 12
2 PCI Hot Plug Utility for Novell NetWare....................................................... 17
Overview.......................................................................................................... 17
NetWare 5 Requirements............................................................................ 19
Novell Configuration Manager Console ...................................................... 20
Slot Options Menu....................................................................................... 22
Slot Detailed Information Screen................................................................. 24
Opening the User Interface ............................................................................. 25
Powering Down a PCI Slot .............................................................................. 26
Removing a Hot Plug Board ............................................................................ 32
Replacing a Hot Plug Board ............................................................................ 36
Powering Up a PCI Slot ................................................................................... 39

1
1 PCI Hot Plug Utility for Windows NT
Opening the Hot Plug Utility
Use this topic only for Microsoft's Windows NT 4.0 on the HP NetServer LXr
8500 using the software utility to perform PCI Hot Plug Replacement (or Online
Replacement) operations. This topic and its subsequent topics describe how to
turn power Off and On to the PCI slots (P1-P10) using the PCI Hot Plug Utility.
For Novell's NetWare 5 NOS, go to the topics under Chapter 2 "Hot Plug
Replacement (NetWare)".
CAUTION To prevent a system crash or hang, never remove a PCI board
from a slot with power on. Always use the Hot Plug Utility to
turn power off to the Hot Plug slot before performing any
replacements.
The PCI board is only Hot Plug-capable if it has a hot plug compliant driver
available and installed on the HP NetServer. If the PCI board is not Hot Plug-
capable, remove and replace the board with the HP NetServer's power turned off.
Microsoft’s Windows NT 4.0 does not, by itself, support hot plug replacement,
but HP Configuration Assistant on the HP Navigator CD-ROM, installs the PCI
Hot Plug Utility on the NT server, along with the system software and the drivers
for some of the HP supported PCI Hot Plug boards. Through this Utility,
Windows NT 4.0 does support hot replacement of identical boards. The PCI Hot
Plug Utility is also found in the diskette library on the Navigator CD-ROM. If
using manual installation, follow the installation instructions found in the
readme.txt file to install the Utility on the NT NetServer.
The Hot Plug Utility is used to replace the PCI Hot Plug board in a four-step
process:
1. Turning power off to the PCI slot
2. Removing the PCI board
3. Replacing the PCI board
4. Turning power on to the PCI slot
The Hot Plug Utility is used to turn power off to the PCI slot before removing the
PCI board, and then after replacing the PCI board, it is used to turn power back on

Chapter 1 Server Administration Using HP TopTools
2
to the PCI slot. Refer to the Help File for a description of the PCI Hot Plug
Utility's buttons and functions.
NOTE The Power Button is the only button required to do basic Hot
Plug Replacement.
Opening the PCI Hot Plug Utility
Use this procedure to open the PCI Hot Plug Utility in Windows NT 4.0.
NOTE If the left P (Power) LED is lit (green) in the PCI Hot Plug
Utility, the corresponding Power LED on the rear panel will be
green. This is also true for the right A (Attention) LED; that is,
if the right A (Attention) LED is lit (red) in the PCI Hot Plug
Utility, the corresponding Attention LED on the rear panel will
be amber.
1. In Windows NT 4.0, click on the Start button and then select the
Programs menu.
2. From the Programs menu, select PCI Hot Plug and then select the PCI Hot
Plug Utility.
A display similar to the example shown in Figure 1 appears.
This example has 9 slots filled with PCI boards. Slot 1 shows no board
installed and slot 2 has no hot plug compliant driver. Slots 2 to 6 and 9 to
10 all have power applied to the slot, shown by the P (Power) LED turned
on, (left P LEDs are green with Normal in status field) and are operating
normally. Slot 7 has a left P LED on (green), but also has a fault condition
indicated by the right A (Attention) LED (red), with its status field
displaying Link Fault, suggesting a corrective action. Slot 8 has a green P
LED, but has *Mixed – multiple device board (represents a multifunction
adapter) in the status field. See Help file for more information about
functions and buttons.

Chapter 1 PCI Hot Plug Utility for Microsoft Windows NT
3
Figure 1. PCI Hot Plug Utility
3. If no hot plug support appears under Board in the Utility's window
instead of the desired PCI board, one of the following conditions might be
true:
àThe PCI Hot Plug board is not supported by a hot plug compliant
software driver.
àThe software driver for the PCI Hot Plug board is not properly installed
and loaded.
See Windows NT Help for how to load drivers.
àThe PCI board may not use a driver, or the driver is defective.
NOTE If you have a board without a hot plug compliant driver in one
of the hot plug slots, the board will show up in the Utility as no
hot plug support, and the Utility will not allow you to power
down the slot.
4. Identify the physical location of the desired PCI Hot Plug board, using the
PCI Hot Plug Utility and Figures 2 and 3.

Chapter 1 Server Administration Using HP TopTools
4
PCI Hot Plug
LED Indicators
(Amber)
Power
A
ttention
P10 P9 P8 P7 P6 P5 P4 P3 P2 P1
Figure 2. PCI Slot Locations (Rear view)
Battery
IDE (CD-ROM)
Flexible Disk
Drive
SCSI A
SCSI B
I/O Riser
Slot
PCI LED
Display
Cable
IC
2
(J1F1)
Remote Contro
l
Board Cable
Auxiliary I C
2
P10-P9
+3.3 VDC
66/33 MHz
P8-P7
+3.3 VDC
66/33 MHz
P6-P3
+5 VDC
33 MHz
P2-P1
+5 VDC
33 MHz
Remote Control
Board must be
in slot P2.
10 9 87654321
Configuration
Switch Block
Bus 0
Bus 1
Bus 2
Bus 3
Figure 3. PCI Slot Locations (I/O Baseboard top view)

Chapter 1 PCI Hot Plug Utility for Microsoft Windows NT
5
Powering Down a PCI Slot
Use this topic to select and power down a PCI slot on the I/O baseboard.
1. Select the desired PCI slot (slot P7) to replace by pointing to it with the
mouse cursor. See Figure 4.
This example has a red A (Attention) LED fault condition associated with
it.
2. Left click on the desired slot (slot P7) with the mouse.
Figure 4. Selecting PCI Slot to Turn Power Off
CAUTION Opening a PCI hold-down latch with power applied to the slot
may result in a system crash or hang. Always use the Utility to
first power off the slot. Turning off power to any slot will stop
all input (I/O) or services associated with the board while
power is turned off to the slot.
3. Click on the Power button in the upper right of the screen. See Figure 1.
A pop-up prompt appears requesting conformation of this action.
See Figure 5.

Chapter 1 Server Administration Using HP TopTools
6
NOTE The Power button is the only button required to do basic Hot
Plug Replacement operations.
Figure 5. Pop-up Menu
4. Confirm your selection by clicking on Yes.
As soon as confirmation is complete, the left P (Power) LED in the Utility
window turns off (gray) and the slot status changes from "Link Fault" (or
Normal)to Not Ready. The corresponding Power LED (green) for the PCI
slot on the rear panel will also turn off. This means power to this slot is
turned off. See Figure 6.
CAUTION If the rear panel Power LED for the desired PCI slot does not
turn off, do not attempt to remove the PCI Hot Plug board.
Return to Step 1 in this procedure to ensure you have selected
the correct slot to power down.
NOTE If you have a PCI board with a non-compliant drive in the
desired PCI slot, the PCI board will show up on the Utility’s