HP A3100-48 v2 Installation instructions

Product End-of-Life Disassembly Instructions
Product Category: Networking Equipment
Marketing Name / Model
[List multiple models if applicable.]
HP A3100-48 v2 Switch (JG315A)
HP A3600-48 v2 SI Switch (JG305A)
Purpose: The document is intended for use by end-of-life recyclers or treatment facilities. It provides the basic instructions
for the disassembly of HP products to remove components and materials requiring selective treatment, as defined by EU
directive 2002/96/EC, Waste Electrical and Electronic Equipment (WEEE).
1.0 Items Requiring Selective Treatment
1.1 Items listed below are classified as requiring selective treatment.
1.2 Enter the quantity of items contained within the product which require selective treatment in the right column, as
applicable.
Item Description Notes
Quantity
of items
included
in product
Printed Circuit Boards (PCB) or Printed Circuit
Assemblies (PCA) With a surface greater than 10 sq cm 2
Batteries All types including standard alkaline and lithium coin
or button style batteries 0
Mercury-containing components For example, mercury in lamps, display backlights,
scanner lamps, switches, batteries 0
Liquid Crystal Displays (LCD) with a surface greater
than 100 sq cm Includes background illuminated displays with gas discharge lamps 0
Cathode Ray Tubes (CRT) 0
Capacitors / condensers (Containing PCB/PCT) 0
Electrolytic Capacitors / Condensers measuring
greater than 2.5 cm in diameter or height 0
External electrical cables and cords 0
Gas Discharge Lamps 0
Plastics containing Brominated Flame Retardants
weighing > 25 grams (not including PCBs or PCAs
already listed as a separate item above)
2
Components and parts containing toner and ink,
including liquids, semi-liquids (gel/paste) and toner Include the cartridges, print heads, tubes, vent chambers, and service stations. 0
Components and waste containing asbestos 0
Components, parts and materials containing
refractory ceramic fibers 0
Components, parts and materials containing
radioactive substances 0
EL-MF877-00 Page 1
Template Revision B
PSG instructions for this template are available at EL-MF877-01

EL-MF877-00 Page 2
Template Revision B
PSG instructions for this template are available at EL-MF877-01
2.0 Tools Required
List the type and size of the tools that would typically be used to disassemble the product to a point where components
and materials requiring selective treatment can be removed.
Tool Description Tool Size (if
applicable)
Screw driver 2#
3.0 Product Disassembly Process
3.1 List the basic steps that should typically be followed to remove components and materials requiring selective treatment:
1. Unscrew the Power Cable Holder 1.
2. Unscrew all screws 2, and then remove the mounting angle 3.
3. Remove top cover 4, and then remove plastic panel 5.
4. Remove all of the inner cables.
5. Unscrew all screws on support 7, and then remove support 7 from the chassis.
6. Unscrew all screws on fan 8, and then remove fan 8 from the chassis.
7. Unscrew all screws on power connector 9, and then remove power connector 9 from the chassis.
8. Unscrew all screws on PCB 10, and then remove PCB 10 from the base.
9. Unscrew all screws on Part 11 , and then remove Part 11 from the base.
10. Remove all of the labels from the chassis.
11. Unscrew all screws on PCB 10-2, and then remove the insulation pad from PCB 10-1.
12. Unscrew part 10-3 from PCB 10, and then remove part 10-3.
13. Remove part 10-4 from PCB 10.
3.2 Optional Graphic. If the disassembly process is complex, insert a graphic illustration below to identify the items
contained in the product that require selective treatment (with descriptions and arrows identifying locations).
Figure 1 Unscrew the Power Cable Holder 1 and screw 2 Figure 2 Treatments to the product (rear view)

Figure 3 Treatments to the product Figure 4 Treatments to the product
Figure 5 Treatments to PCB 10
EL-MF877-00 Page 3
Template Revision B
PSG instructions for this template are available at EL-MF877-01