HP AdvanceStack Switch 2000 User manual

Connectivity Quick Reference
for the HP AdvanceStack Switch 2000
100VG Connectivity
•Basic Configuration Guidelines:
The default Mode setting for the 100VG ports on the Switch 2000 and Switch-16 is
Auto Detect. When connecting these switches to other network devices, such as hubs
or other switches, the Auto Detect setting works in most cases and should be tried
before making any configuration changes. When connecting these switches to PCs and
workstations that have HP 10/100VG LAN Adapters, HP recommends setting the
Mode to Master.
Other allowable Mode settings are shown in the illustrations on the following pages
under “Port Mode”. The port Mode can be set through the Configuration menu using
the Switch 2000 console interface.
•Connections: 100VG ports on the Switch 2000 must not be connected to any 100VG
ports labeled “Uplink”. These ports are reserved for hub-to-hub connections.
Note that the illustrations show only twisted-pair connections; devices supporting
fiber-optic connections are connected similarly.
To connect to Set 100VGPort Modeto
Network device Auto Detect
PC orworkstation Master
☞
☞
sd4pdf.fm5 Page 1 Thursday, February 20, 1997 4:31 PM

100VG Connectivity
2
Switch 2000 to 100VG Hub
Switch 2000 to PC
Use any Downlink port
Port Mode
Auto Detect
OR
End Node
Any End Node
(ForExample, a
PC or Server)
sd4pdf.fm5 Page 2 Thursday, February 20, 1997 4:31 PM

100VG Connectivity
3
Switch 2000 to Switch 2000
Switch 2000 to Switch-16
Auto
Detect
Auto
Detect
Master
End
Node Master
End
Node
OR OR
PortModes
Auto
Detect
Auto
Detect
Master
End
Node Master
End
Node
OR OR
Port Modes
sd4pdf.fm5 Page 3 Thursday, February 20, 1997 4:31 PM

100VG Connectivity
4
Switch 2000 to Switch 200
Switch 2000 to Router 650
0ORT-ODE
Auto Detect
OR
End Node
Use Downlink Port
Port Mode
Auto Detect
OR
Master
sd4pdf.fm5 Page 4 Thursday, February 20, 1997 4:31 PM

UTP Ethernet/10Base-T Connectivity
5
UTP Ethernet/10Base-T Connectivity
Ethernet connectivity includes twisted pair (UTP) cabling (below), and fiber-optic cabling (page 9).
Twisted Pair Cabling
The Ethernet module for the Switch 2000 has 10Base-T ports that operate as MDI-X ports, and a slot to install a
10Base-T transceiver that operates as an MDI port.
•MDI-X Operation: The four 10Base-T ports built into the module are designed for MDI-X operation (that is, for
connecting end nodes to the switch). Thus, if you connect any of these ports to an MDI-X port on another device,
use a “crossover” cable. But if the connection is to an MDI port, use a “straight-through” cable.
•MDI Operation: An optional 10Base-T transceiver in the transceiver slot operates in MDI mode (that is, for con-
necting hubs or other switches to the Switch 2000). In this case, use a “straight-through” cable to connect the
transceiver to an MDI-X port on another device, or a “crossover cable” to connect the transceiver to another trans-
ceiver or other MDI port on another device.
Note that if the connection from the 10Base-T transceiver is to another HP 10Base-T transceiver (requiring a cross-
over cable), the “long cable” option can be set on both transceivers, allowing the connection to be up to 200 meters.
See the transceiver documentation for more information. (For more on straight-through and crossover cables, see
appendix A, “Cables and Connectors”, in the HP AdvanceStack Switch 2000 Installation Guide.)
Switch 2000 to AdvanceStack 10Base-T 48-Port Hub
CrossoverCable
sd4pdf.fm5 Page 5 Thursday, February 20, 1997 4:31 PM

UTP Ethernet/10Base-T Connectivity
6
Switch 2000 to PC
Switch 2000 to Switch 2000, Switch-16, or Switch 200
Any End Node
(ForExample, a
PC or Server)
Straight-Through Cable
Note: This illustration also applies
whenconnectingaSwitch2000toa
Switch-16 or a Switch 200.
Crossover Cable
sd4pdf.fm5 Page 6 Thursday, February 20, 1997 4:31 PM

UTP Ethernet/10Base-T Connectivity
7
Switch 2000 to Switch 208T
Switch 2000 to Switch 800T
Crossover Cable
Illustrates use of Switch 800T’s 10/100
capability for a 10 Mbit/connection.
Port Mode
Switch 2000:Half Duplex
Switch 800T:Auto Detector 10/Half Dx
Switch 2000:Full Duplex
Switch 800T:Auto Detector 10/Full Dx
Crossover Cable
sd4pdf.fm5 Page 7 Thursday, February 20, 1997 4:31 PM

UTP Ethernet/10Base-T Connectivity
8
Switch 2000 to Switch 200
Switch 2000 to Router 650
Crossover Cable
Note:As shown in this illustration,
a straight-through cable isused to
connect the Router650 to a built-in
RJ-45port in theSwitch 2000 Ether-
net module. If the connection from
the Router 650 is to a 10Base-T
transceiver in the Switch 2000
Ethernet module, use a crossover
cable instead.
Straight-Through Cable
sd4pdf.fm5 Page 8 Saturday, February 22, 1997 12:00 PM

Fiber Optic 10Base-FL Connectivity
9
Fiber Optic 10Base-FL Connectivity
The 10Base-FL module for the Switch 2000 has four ports offering half-duplex or full-duplex operation. The module
supports the following fiber cable and connector types:
• 62.5/125 µm multimode graded-index fiber cable
• ST connectors
Switch 2000 to an AdvanceStack Hub
sd4pdf.fm5 Page 9 Thursday, February 20, 1997 4:31 PM

Fiber Optic 10Base-FL Connectivity
10
Switch 2000 to Another Switch 2000
Switch 2000 to a Switch-16
OR
sd4pdf.fm5 Page 10 Thursday, February 20, 1997 4:31 PM