HP FlexNetwork 7506X Assembly instructions

Page 1
Product End-of-Life Disassembly Instructions
Product Category: Networking Equipment
Marketing Name / Model
[List multiple models if applicable.]
HPE FlexNetwork 7506X PoE Ethernet Switch 6 slots Chassis(R8N48A)
Purpose: The document is intended for use by end-of-life recyclers or treatment facilities. It provides the basic instructions
for the disassembly of HPE products to remove components and materials requiring selective treatment, as defined by EU
directive 2012/19/EC, Waste Electrical and Electronic Equipment (WEEE).
1.0 Items Requiring Selective Treatment
1.1 Items listed below are classified as requiring selective treatment.
1.2 Enter the quantity of items contained within the product which require selective treatment in the right column, as
applicable.
Item Description
Notes
Quantity
of items
included
in product
Printed Circuit Boards (PCB) or Printed Circuit
Assemblies (PCA)
With a surface greater than 10 sq cm
2
Batteries
All types including standard alkaline and lithium
coin or button style batteries
0
Mercury-containing components
For example, mercury in lamps, display backlights,
scanner lamps, switches, batteries
0
Liquid Crystal Displays (LCD) with a surface
greater than 100 sq cm
Includes background illuminated displays with gas
discharge lamps
0
Cathode Ray Tubes (CRT)
0
Capacitors / condensers (Containing PCB/PCT)
0
Electrolytic Capacitors / Condensers measuring
greater than 2.5 cm in diameter or height
0
External electrical cables and cords
0
Gas Discharge Lamps
0
Plastics containing Brominated Flame Retardants
weighing > 25 grams (not including PCBs or PCAs
already listed as a separate item above)
0
Components and parts containing toner and ink,
including liquids, semi-liquids (gel/paste) and toner
Include the cartridges, print heads, tubes, vent
chambers, and service stations.
0
Components and waste containing asbestos
0
Components, parts and materials containing
refractory ceramic fibers
0
Components, parts and materials containing
radioactive substances
0

Page 2
2.0 Tools Required
List the type and size of the tools that would typically be used to disassemble the product to a point where components
and materials requiring selective treatment can be removed.
Tool Description
Tool Size (if
applicable)
Screwdriver
#2
Diagonal Cutters
3.0 Product Disassembly Process
3.1 List the basic steps that should typically be followed to remove components and materials requiring selective treatment:
1. Unscrew the screws on mounting angle 2, and then remove mounting angle 2.
2. Unscrew the screws on cabling rack 3, and then remove cabling rack 3 from mounting angle 2.
3. Unscrew the screws on front panel 4, and then remove front panel 4.
4. Unscrew the screws on front panel 5, and then remove front panel 5.
5. Unscrew the screws on front panel 6, and then remove front panel 6.
6. Remove film 7.
7. Remove film 8.
8. Unscrew the screws on fan module frame 9, and then remove fan module frame 9.
9. Unscrew the screws on rear cover plate 10, and then remove rear cover plate 10.
10. Unscrew the screws on reinforcing plate 12, and then remove reinforcing plate 12.
11. Unscrew the screws on reinforcing plate 11, and then remove reinforcing plate 11.
12. Unscrew the screws on PCB 13, and then remove PCB 13.
13. Unscrew the screws on busbar 14, and then remove busbar 14.
14. Remove all the labels.
15. Remove all shielding fingers.
16. Remove shielding gasket 4-2 from blank panel 4-1.
17. Remove film 4-3 from blank panel 4-1.
18. Remove shielding gasket 5-2 from blank panel 5-1.
19. Remove film 5-3 from blank panel 5-1.
20. Remove the nine fans 9-2 from fan frame 9-1.
21. Unscrew the screws on PCB 9-3, and then remove PCB 9-3.
22. Remove all of the inner cables.
23. Unscrew the screws on handle 9-4, and then remove handle 9-4.
24. Remove film 9-5 from fan frame 9-1.
25. Remove shielding finger 9-6 from fan frame 9-1.
26. Unscrew the screws on guide pin 13-2, and then remove guide pin 13-2.
3.2 Optional Graphic. If the disassembly process is complex, insert a graphic illustration below to identify the items
contained in the product that require selective treatment (with descriptions and arrows identifying locations).

Page 3
Figure 1. Front of the product
Figure 2. Rear of the product

Page 4
Figure 3 Treatments to module 4
Figure 4 Treatments to module 5

Page 5
Figure 5 Treatments to fan module 9
Figure 6 Treatments to module 13