HP HPE FlexFabric 5930 User manual

HPE FlexFabric 5930 Switch Series
Installation Guide
Part number: 5998-7149s
Document version: 6W103-20160516

© Copyright 2016 Hewlett Packard Enterprise Development LP
The information contained herein is subject to change without notice. The only warranties for Hewlett Packard
Enterprise products and services are set forth in the express warranty statements accompanying such
products and services. Nothing herein should be construed as constituting an additional warranty. Hewlett
Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.
Confidential computer software. Valid license from Hewlett Packard Enterprise required for possession, use, or
copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software
Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor’s
standard commercial license.
Links to third-party websites take you outside the Hewlett Packard Enterprise website. Hewlett Packard
Enterprise has no control over and is not responsible for information outside the Hewlett Packard Enterprise
website.
Acknowledgments
Intel®, Itanium®, Pentium®, Intel Inside®, and the Intel Inside logo are trademarks of Intel Corporation in the
United States and other countries.
Microsoft® and Windows® are trademarks of the Microsoft group of companies.
Adobe® andAcrobat® are trademarks ofAdobe Systems Incorporated.
Java and Oracle are registered trademarks of Oracle and/or its affiliates.
UNIX® is a registered trademark of The Open Group.

i
Contents
Preparing for installation ················································································· 1
Safety recommendations ···································································································································2
Examining the installation site····························································································································2
Temperature/humidity ································································································································3
Cleanliness·················································································································································3
EMI·····························································································································································3
Laser safety················································································································································4
Installation tools ·················································································································································4
Installation accessories······································································································································4
Installing the switch························································································· 7
Installing the switch in a 19-inch rack ················································································································8
Installation accessories ······························································································································8
Rack-mounting procedures at a glance ···································································································10
Attaching the mounting brackets, chassis rails, and grounding cable to the chassis·······························11
Attaching the slide rails to the rack ··········································································································15
Mounting the switch in the rack················································································································16
Grounding the switch ·······································································································································18
Grounding the switch with a grounding strip ····························································································19
Grounding the switch by using the AC power cord ··················································································19
Installing/removing a fan tray ···························································································································20
Installing a fan tray ···································································································································21
Removing a fan tray ·································································································································22
Installing/removing a power supply··················································································································23
Installing a power supply··························································································································24
Removing a power supply························································································································25
Connecting the power cord ······························································································································26
Connecting the 650W AC power supply ··································································································27
Connecting the 650W DC power supply ··································································································27
Installing/Removing an interface module ·································································································28
Verifying the installation ···································································································································30
Accessing the switch for the first time··························································· 31
Setting up the configuration environment ········································································································31
Connecting the console cable··························································································································31
Serial console cable ·································································································································31
USB mini console cable ···························································································································32
Connection procedure······························································································································32
Setting terminal parameters·····························································································································34
Powering on the switch ····································································································································34
Setting up an IRF fabric ················································································ 36
IRF fabric setup flowchart ································································································································36
Planning IRF fabric setup·································································································································37
Planning IRF fabric size and the installation site······················································································37
Identifying the master switch and planning IRF member IDs···································································37
Planning IRF topology and connections···································································································38
Identifying physical IRF ports on the member switches ···········································································39
Planning the cabling scheme ···················································································································39
Configuring basic IRF settings ·························································································································40
Connecting the physical IRF ports ···················································································································40
Accessing the IRF fabric to verify the configuration ·························································································40
Maintenance and troubleshooting································································· 42
Power supply failure·········································································································································42
Fan tray failure ·················································································································································42
Configuration terminal problems ······················································································································42

ii
No terminal display···································································································································43
Garbled terminal display ··························································································································43
Appendix A Chassis views and technical specifications ······························· 44
Chassis views ··················································································································································44
HPE 5930-32 QSFP+/HPE 5930-32 QSFP+ TAA ···················································································44
HPE 5930-2Slot+2QSFP+/HPE 5930-2Slot+2QSFP+ TAA·····································································45
HPE 5930-4Slot/HPE 5930-4Slot TAA·····································································································46
Technical specifications ···································································································································48
Appendix B FRUs and compatibility matrixes ··············································· 50
Power supplies·················································································································································50
Fan trays ··························································································································································51
Interface modules ············································································································································52
Appendix C Ports and LEDs ········································································· 54
Ports·································································································································································54
Console port·············································································································································54
Management Ethernet port ······················································································································54
USB port···················································································································································54
SFP+ port·················································································································································55
QSFP+ port ··············································································································································57
1/10GBase-T autosensing Ethernet port··································································································59
LEDs ································································································································································59
System status LED···································································································································59
SFP+ port LED·········································································································································60
QSFP+ port LED ······································································································································60
Management Ethernet port LEDs·············································································································60
1/10GBase-T autosensing Ethernet port LEDs························································································61
Fan tray alarm LEDs ································································································································61
Appendix D Cooling system·········································································· 62
HPE 5930-32 QSFP+/HPE 5930-32 QSFP+ TAA/HPE 5930-2Slot+2QSFP+/HPE 5930-2Slot+2QSFP+ TAA
cooling system ·················································································································································62
HPE 5930-4Slot/HPE 5930-4Slot TAA cooling system····················································································63
Document conventions and icons ································································· 65
Conventions ·····················································································································································65
Network topology icons····································································································································66
Support and other resources ········································································ 67
Accessing Hewlett Packard Enterprise Support ······························································································67
Accessing updates···········································································································································67
Websites ··················································································································································68
Customer self repair·································································································································68
Remote support········································································································································68
Documentation feedback ·························································································································69

1
Preparing for installation
Table 1 describes HPE FlexFabric 5930 Switch Series models, power supplies, and fan trays.
Table 1 HPE FlexFabric 5930 Switch Series models, power supplies, and fan trays
Product code HPE description Alias
HPE FlexFabric 5930 switches
JG726A HPE FlexFabric 5930 32QSFP+ Switch HPE 5930-32 QSFP+
JG727A HPE FlexFabric 5930 32QSFP+
TAA-compliant Switch HPE 5930-32 QSFP+ TAA
JH178A HPE FlexFabric 5930 2QSFP+ 2-slot Switch HPE 5930-2Slot+2QSFP+
JH187A HPE FlexFabric 5930 2QSFP+ 2-slot
TAA-compliant Switch HPE 5930-2Slot+2QSFP+ TAA
JH179A HPE FlexFabric 5930 4-slot Switch HPE 5930-4Slot
JH188A HPE FlexFabric 5930 4-slot TAA-compliant
Switch HPE 5930-4Slot TAA
Power supplies
JC680A HPE 58x0AF 650W AC Power Supply 650W AC
JH336A HPE FlexFabric Switch 650W 48V Hot Plug
NEBS-compliant DC Power Supply 650W DC
Fan trays
JG552A HPE X711 Front (Port Side) to Back (Power
Side) Airflow High Volume Fan Tray LSWM1HFANSCB
JG553A HPE X712 Back (Power Side) to Front (Port
Side) Airflow High Volume Fan Tray LSWM1HFANSC
JH185A HPE 5930 4-slot Back (Power Side) to Front
(Port Side) Airflow Fan Tray LSWE1BFANSC
JH186A HPE 5930 4-slot Front (Port Side) to Back
(Power Side) Airflow Fan Tray LSWE1BFANSCB
For regulatory identification purposes, the HPE 5930-32 QSFP+ Switch and HPE 5930-32 QSFP+
TAA Switch are assigned Regulatory Model Numbers (RMNs). The RMNs for these products are
listed below. These regulatory numbers should not be confused with the marketing name HPE
FlexFabric 5930, or the product codes JG726A and JG727A.
Product code RMN Description
JG726A BJNGA-AD0022 HPE FlexFabric 5930 32QSFP+ Switch
JG727A BJNGA-AD0022 HPE FlexFabric 5930 32QSFP+
TAA-compliant Switch
For regulatory identification purposes, the HPE 5930-2Slot+2QSFP+ Switch, HPE
5930-2Slot+2QSFP+ TAA Switch, HPE 5930-4Slot Switch, and HPE 5930-4Slot TAA Switch are
assigned Regulatory Model Numbers (RMNs). The RMNs for these products are listed below. These
regulatory numbers should not be confused with the marketing name HPE FlexFabric 5930, or the
product codes JH178A, JH187A, JH179A, and JH188A.

2
Product code RMN Description
JH178A BJNGA-AD0049 HPE FlexFabric 5930 2QSFP+ 2-slot Switch
JH187A BJNGA-AD0049 HPE FlexFabric 5930 2QSFP+ 2-slot
TAA-compliant Switch
JH179A BJNGA-AD0050 HPE FlexFabric 5930 4-slot Switch
JH188A BJNGA-AD0050 HPE FlexFabric 5930 4-slot TAA-compliant
Switch
Safety recommendations
To avoid any equipment damage or bodily injury caused by incorrect use, read the following safety
recommendations before installation. Note that the recommendations do not cover every possible
hazardous condition.
•Before cleaning the switch, remove all power cords from the switch. Do not clean the switch
with wet cloth or liquid.
•Do not place the switch near water or in a damp environment. Prevent water or moisture from
entering the switch chassis.
•Do not place the switch on an unstable case or desk. The switch might be severely damaged in
case of a fall.
•Ensure good ventilation of the equipment room and keep the air inlet and outlet vents of the
switch free of obstruction.
•Connect the yellow-green protection grounding cable before power-on.
•Make sure the operating voltage is in the required range.
•To avoid electrical shocks, do not open the chassis while the switch is operating or when the
switch is just powered off.
•When replacing FRUs, including power supplies, fan trays, and interface modules, wear an
ESD wrist strap to avoid damaging the units.
Examining the installation site
The switch must be used indoors.
You can mount your switch in a rack. To rack-mount your switch, make sure the following
requirements are met:
•Adequate clearance is reserved at the air inlet and outlet vents for ventilation.
•The rack has a good ventilation system.
•Identify the hot aisle and cold aisle at the installation site, and make sure ambient air flows into
the switch from the cold aisle and exhausts to the hot aisle.
•Identify the airflow designs of neighboring devices, and prevent hot air flowing out of the bottom
device from entering the top device.
•The rack is sturdy enough to support the switch and its accessories.
•The rack is reliably grounded.
To ensure correct operation and long service life of your switch, install it in an environment that meets
the requirements described in the following subsections.

3
Temperature/humidity
Maintain appropriate temperature and humidity in the equipment room.
•Lasting high relative humidity can cause poor insulation, electricity leakage, mechanical
property change of materials, and metal corrosion.
•Lasting low relative humidity can cause washer contraction and ESD and cause problems
including loose screws and circuit failure.
•High temperature can accelerate the aging of insulation materials and significantly lower the
reliability and lifespan of the switch.
For the temperature and humidity requirements of different switch models, see "Appendix A Chassis
views and technical specifications."
Cleanliness
Dust buildup on the chassis might result in electrostatic adsorption, which causes poor contact of
metal components and contact points, especially when indoor relative humidity is low. In the worst
case, electrostatic adsorption can cause communication failure.
Table 2 Dust concentration limit in the equipment room
Substance Concentration limit (particles/m³)
Dust ≤3 x 104 (no visible dust on the tabletop over three days)
NOTE:
Dust diameter ≥5 μm
The equipment room must also meet limits on salts, acids, and sulfides to eliminate corrosion and
premature aging of components, as shown in Table 3.
Table 3 Harmful gas limits in the equipment room
Gas Maximum concentration (mg/m³)
SO20.2
H2S 0.006
NH30.05
Cl20.01
EMI
All electromagnetic interference (EMI) sources, from outside or inside of the switch and application
system, adversely affect the switch in the following ways:
•A conduction pattern of capacitance coupling.
•Inductance coupling.
•Electromagnetic wave radiation.
•Common impedance (including the grounding system) coupling.
To prevent EMI, use the following guidelines:
•If AC power is used, use a single-phase three-wire power receptacle with protection earth (PE)
to filter interference from the power grid.

4
•Keep the switch far away from radio transmitting stations, radar stations, and high-frequency
devices.
•Use electromagnetic shielding, for example, shielded interface cables, when necessary.
Laser safety
WARNING!
Do not stare into any fiber port when the switch has power. The laser light emitted from the optical
fiber might hurt your eyes.
The switch is a Class 1 laser device.
Installation tools
No installation tools are provided with the switch. Prepare the following tools yourself:
•Phillips screwdriver.
•ESD wrist strap.
•Marker.
Installation accessories
Table 4 Installation accessories
Product
code Description Quantity Applicable models
5066-0850
1 U mounting bracket kit
(including one pair of mounting
brackets and eight M4
countersunk screws)
1 kit
•HPE 5930-32 QSFP+
•HPE 5930-32 QSFP+
TAA
5190-0719
Mounting brackets for the HPE
5930-2Slot+2QSFP+/HPE
5930-2Slot+2QSFP+ TAA
1 kit
•HPE 5930-2Slot+2QSFP+
•HPE 5930-2Slot+2QSFP+
TAA

5
Product
code Description Quantity Applicable models
5190-0720
Mounting brackets for the HPE
5930-4Slot/HPE 5930-4Slot TAA
1 kit
•HPE 5930-4Slot
•HPE 5930-4Slot TAA
5185-8681
1 U short slide rail kit (including
one pair of slide rails and four M4
countersunk screws)
1 kit
•HPE 5930-32 QSFP+
•HPE 5930-32 QSFP+
TAA
•HPE 5930-2Slot+2QSFP+
•HPE 5930-2Slot+2QSFP+
TAA
5185-8684
2 U short slide rail kit (including
one pair of slide rails and four M4
countersunk screws)
1 kit
•HPE 5930-4Slot
•HPE 5930-4Slot TAA
5184-6723
Grounding cable
1 All HPE 5930 switches
5185-9579
Grounding screw
2 All HPE 5930 switches
5003-2403
Interface module filler module
1
•HPE 5930-2Slot+2QSFP+
•HPE 5930-2Slot+2QSFP+
TAA
•HPE 5930-4Slot
•HPE 5930-4Slot TAA
5185-8676
Power supply filler module
1 All HPE 5930 switches


6
Product
code Description Quantity Applicable models
5185-8688
5400-0249
DC power cord
The power cord color code
scheme is for illustration only.
The cable delivered for your
country or region might use a
different color scheme.
1 650W DC power supply
5185-8748
Removable cable tie
1 All power supplies
5185-8627
Console cable
1 All HPE 5930 switches
5187-9022
QSFP+ dust plug
Optional
•HPE 5930-32 QSFP+
•HPE 5930-32 QSFP+
TAA
•HPE 5930-2Slot+2QSFP+
•HPE 5930-2Slot+2QSFP+
TAA


7
Installing the switch
CAUTION:
Keep the tamper-proof seal on a mounting screw on the chassis cover intact, and if you want to open
the chassis, contact Hewlett Packard Enterprise for permission. Otherwise, Hewlett Packard
Enterprise shall not be liable for any consequence caused thereby.
Figure 1 Hardware installation flow
Ground the switch
Install the switch
Start
Connect the power cords
Verify the installation
Power on the switch
Operating correctly? Power off the switch
Resolve the problem
No
Yes
Install fan trays
Install power supplies
Install interface cards?
No
Yes
Install interface cards
Operating correctly? Resolve the problem
Yes
No
End

8
Installing the switch in a 19-inch rack
IMPORTANT:
To close the rack door easily, make sure the rack depth is a minimum of 1000 mm (39.37 in).
Installation accessories
Table 5 Installation accessories
Switch model Mounting brackets
(provided)
Cable
management
brackets
Rack mounting rail kit
(provided)
•HPE 5930-32 QSFP+
•HPE 5930-32 QSFP+
TAA
1U high, one pair.
See Figure 2. N/A
1U high, including one pair of
chassis rails and one pair of
slide rails. See Figure 5.
•HPE
5930-2Slot+2QSFP+
•HPE
5930-2Slot+2QSFP+
TAA-compliant
1U high, one pair.
See Figure 3. N/A
1U high, including one pair of
chassis rails and one pair of
slide rails. See Figure 5.
•HPE 5930-4Slot
•HPE 5930-4Slot TAA
2U high, one pair.
See Figure 4.
One pair
(provided).
See Figure 4.
2U high, including one pair of
chassis rails and one pair of
slide rails. See Figure 6.
Figure 2 Mounting brackets for the HPE 5930-32 QSFP+/HPE 5930-32 QSFP+ TAA switch

9
Figure 3 Mounting brackets for the HPE 5930-2Slot+2QSFP+/HPE 5930-2Slot+2QSFP+ TAA
switch
Figure 4 Mounting brackets for the HPE 5930-4Slot/HPE 5930-4Slot TAA switch
(1) Cable management bracket (2) Mounting bracket
Figure 5 1U rack mounting rail kit
(1) Chassis rail (2) Slide rail
1 2

10
Figure 6 2U rack mounting rail kit
(1) Chassis rail (2) Slide rail
Rack-mounting procedures at a glance
Figure 7 Rack-mounting procedure
NOTE:
If a rack shelf is available, you can put the switch on the rack shelf, slide the switch to an appropriate
location, and attach the switch to the rack with the mounting brackets.
Follow these guidelines when you install the switch in a 19-inch rack:
•The distance between the front and rear posts of the rack must meet the requirements
described in Table 6.
•To secure the switch to the rack, you must install not only mounting brackets, but also chassis
rails and slide rails.
Table 6 Distance requirements between the front and rear rack posts
Switch model Installation method Minimum distance Maximum distance
•HPE 5930-32 QSFP+
•HPE 5930-32 QSFP+
TAA
Using provided mounting
brackets and chassis rails 405 mm (15.94 in) 854 mm (33.62 in)
•HPE
5930-2Slot+2QSFP+
•HPE
5930-2Slot+2QSFP+
TAA
Using provided mounting
brackets and chassis rails 520 mm (20.47 in) 789 mm (31.06 in)
•HPE 5930-4Slot
•HPE 5930-4Slot TAA
Using provided mounting
brackets and chassis rails 518 mm (20.39 in) 888 mm (34.96 in)

11
Attaching the mounting brackets, chassis rails, and
grounding cable to the chassis
The switch has one mounting position near the network ports and one mounting position near the
power supplies for mounting brackets.
The HPE 5930-32 QSFP+/HPE 5930-32 QSFP+ TAA/HPE 5930-4Slot/HPE 5930-4Slot TAA
switches provide three grounding points: primary grounding point (with a grounding sign), auxiliary
grounding point 1, and auxiliary grounding point 2. The HPE 5930-2Slot+2QSFP+/HPE
5930-2Slot+2QSFP+ TAA switch provides two grounding points: primary grounding point (with a
grounding sign) and auxiliary grounding point 1.
Figure 8 Mounting and grounding positions on the HPE 5930-32 QSFP+/HPE 5930-32 QSFP+
TAA switch
(1) Auxiliary grounding point 2 (2) Power supply-side mounting position
(3) Primary grounding point (4) Auxiliary grounding point 1
(5) Network port-side mounting position
Figure 9 Mounting and grounding positions on the HPE 5930-2Slot+2QSFP+/HPE
5930-2Slot+2QSFP+ TAA switch
(1) Power supply-side mounting position (2) Primary grounding point
(3) Auxiliary grounding point 1 (4) Network port-side mounting position
1 2 3 4 5

12
Attaching the mounting brackets and chassis rails to the chassis
1. Align the mounting brackets with the screw holes in the chassis. Use M4 screws (provided) to
attach the mounting brackets to the chassis.
{To install the mounting brackets at the power supply-side mounting position, see Figure
10, Figure 11,and Figure 12.
{To install the mounting brackets at the network port-side mounting position, see Figure
13, Figure 14, and Figure 15.
2. Align the chassis rails with the rail mounting holes in the chassis:
{If the mounting brackets are in the power supply-side mounting position, align the chassis
rails with the screw holes at the front of the side panels (see Figure 10, Figure 11,
and Figure 12).
{If the mounting brackets are in the network port-side mounting position, align the chassis
rails with the screw holes at the rear of the side panels (see Figure 13, Figure 14, and Figure
15).
3. Use M4 screws (provided) to attach the chassis rails to the chassis.
NOTE:
•Secure the mounting brackets and chassis rails to both sides of the chassis in the same way.
•To install the mounting brackets at the network port-side mounting position on the HPE
5930-2Slot+2QSFP+/HPE 5930-2Slot+2QSFP+ TAA/HPE 5930-4Slot/HPE 5930-4Slot TAA
switches, use the four screw holes nearest to the network port side. To install the mounting
brackets at the power supply-side mounting position on the HPE 5930-2Slot+2QSFP+/HPE
5930-2Slot+2QSFP+ TAA/HPE 5930-4Slot/HPE 5930-4Slot TAA switches, use the four screw
holes nearest to the power supply side.
Figure 10 Attaching the mounting brackets and chassis rails to the HPE 5930-32 QSFP+/HPE
5930-32 QSFP+ TAA switch (power supply-side mounting position for the mounting
brackets)

13
Figure 11 Attaching the mounting brackets and chassis rails to the HPE
5930-2Slot+2QSFP+/HPE 5930-2Slot+2QSFP+ TAA switch (power supply-side mounting
position for the mounting brackets)
Figure 12 Attaching the mounting brackets and chassis rails to the HPE 5930-4Slot/HPE
5930-4Slot TAA switch (power supply-side mounting position for the mounting brackets)
Figure 13 Attaching the mounting brackets and chassis rails to the HPE 5930-32 QSFP+/HPE
5930-32 QSFP+ TAA switch (network port-side mounting position for the mounting brackets)

14
Figure 14 Attaching the mounting brackets and chassis rails to the HPE
5930-2Slot+2QSFP+/HPE 5930-2Slot+2QSFP+ TAA switch (network port-side mounting
position for the mounting brackets)
Figure 15 Attaching the mounting brackets and chassis rails to the HPE 5930-4Slot/HPE
5930-4Slot TAA switch (network port-side mounting position for the mounting brackets)
Connecting the grounding cable to the chassis
CAUTION:
Select grounding points as required. The primary grounding point and auxiliary grounding point 1 are
located on the left side panel. If you use one of these grounding points, you must connect the
grounding cable to the grounding point before you mount the switch in the rack.
As a best practice, connect the grounding cable to the primary grounding point or auxiliary grounding
point 1. The grounding cable and grounding screw that come with the switch are suitable only for
these two grounding points.
To use auxiliary grounding point 2, prepare a grounding cable yourself.
This section uses the primary grounding point on the HPE 5930-32 QSFP+/HPE 5930-32 QSFP+
TAA switch as an example.
To connect the grounding cable to a grounding point:
1. Choose a grounding point.
2. Unpack the grounding cable and grounding screws.
You can use the cable and screws shipped with the switch only for connecting to the primary
grounding point or auxiliary grounding point 1.

15
3. Align the two-hole grounding lug at one end of the cable with the grounding holes of the
grounding point, insert the grounding screws into the holes, and tighten the screws with a
screwdriver, as shown in Figure 10.
Figure 16 Attaching the grounding cable to the primary grounding point on the HPE
FlexFabric 5930-32Q switch
Attaching the slide rails to the rack
The procedures are the same for attaching 1U and 2U slide rails to the rack. This section uses the 1U
slide rails as an example.
To attach the slide rails to the rack:
1. Identify the rack attachment position for the slide rails.
2. Install cage nuts (user-supplied) in the mounting holes in the rack posts.
3. Align the screw holes in one slide rail with the cage nuts in the rack post on one side, and use
screws (user-supplied) to attach the slide rail to the rack, as shown in Figure 17.
4. Repeat the preceding steps to attach the other slide rail to the rack post on the other side.
Keep the two slide rails at the same height so the slide rails can attach into the chassis rails.
Figure 17 Installing the 1U slide rails

16
Mounting the switch in the rack
This task requires two people.
To mount the switch in the rack:
1. Wear an ESD wrist strap and make sure it makes good skin contact and is reliably grounded.
2. Verify that the mounting brackets and chassis rails have been securely attached to the switch
chassis.
3. Verify that the slide rails have been correctly attached to the rear rack posts.
4. Install cage nuts (user-supplied) to the front rack posts and make sure they are at the same
level as the slide rails.
5. One person performs the following operations:
a. Supporting the bottom of the switch, aligns the chassis rails with the slide rails on the rack
posts.
b. Pushes the switch slowly to slide the chassis rails along the slide rails until the mounting
brackets are flush with the rack posts.
6. Another person uses screws (user-supplied) to attach the mounting brackets to the rack.
To secure the switch in the rack, make sure the front ends of the slide rails reach out of the
chassis rails.
The rack-mounting procedures are the same for the HPE 5930-32 QSFP+/HPE 5930-32 QSFP+
TAA/HPE 5930-2Slot+2QSFP+/HPE 5930-2Slot+2QSFP+ TAA switches. The following figures use
the HPE 5930-2Slot+2QSFP+/HPE 5930-2Slot+2QSFP+ TAA switch as an example.
Figure 18 Mounting the HPE 5930-2Slot+2QSFP+/HPE 5930-2Slot+2QSFP+ TAA switch in the
rack (power supply-side mounting position for the mounting brackets)