HSS Hire 57432 Troubleshooting guide

Safety Inspection
Lamp and
Industrial Festoon
Lights
©HSS Hire Service Group Plc 1997 No. 618/01
Group Office: 25 Willow Lane, Mitcham, Surrey CR4 4TS
Hire Shops
For general lighting, indoors or out.
Operating & Safety Guide 618
Contact your local
0990 282828

Never use the festoon or inspection lamp for
anything other than its intended purpose. If it will
not do what you want, assume you have the wrong
equipment for the job. Contact your local HSS Hire Shop
for advice.
Never expose the equipment to excessive
moisture, dust or dangerous/corrosive chemicals.
Keep the equipment clean. You will find this less of a
chore if you clean it regularly, rather than wait until the
end of the hire period.
Handle the equipment with care, even site lighting
contains delicate bulbs and will be damaged by
rough treatment.
Always switch OFF and unplug the festoon or
inspection lamp before making any alterations or
adjustments to it.
When not in use, store the equipment somewhere
EQUIPMENT CARE
clean, dry and safe from thieves.
Having switched off and unplugged the festoon or
inspection lamp, wait for it to cool before packing
ready for return.
Finally, neatly coil the flex ready for return to your
local HSS Hire Shop.
FINISHING OFF
Code 57432/57513
Safety
Inspection
Light

For advice on the safety and suitability of this
equipment contact your local HSS Hire Shop.
Keep children, animals and bystanders away from
the work area.
Never use this equipment if you are ill, feeling
tired, or under the influence of alcohol or drugs.
This equipment should only be used by a
competent person who has read and understood
these instructions.
Wear sensible, reasonably protective clothing
and footwear plus any safety wear
appropriate to the work in progress.
Check the condition of the equipment before use.
If it shows signs of damage or excessive wear, return it to
your local HSS Hire Shop.
Never leave the equipment switched ON and
unattended.
Lights get hot. Always leave them to cool before
touching them and never remove or interfere with any
safety guards fitted.
Never use these lights in the presence of highly
inflammable vapours or liquids.
Information on COSHH regulations is available from your
local HSS Hire Shop.
Most HSS lights plug into a standard 13amp power
socket. However, 110V lights (with a round yellow
plug) must be provided with a suitable 110V
generated supply, or powered from the mains via a
suitable 110V transformer.
Leads should be fully unwound and loosely coiled,
away from the work area. Never run them through
water, over sharp edges or where they could
trip someone.
Keep the equipment dry. Using electrical
equipment in very damp or wet conditions can be
dangerous.
If the equipment fails, or if its plug or lead gets
damaged, return it. Never try to repair it yourself.
For Festoons: if a bulb fails ensure the festoon is
isolated from the power supply before replacing
the bulb.
For Safety Inspection Lamp: if the bulb fails DO
NOT attempt to replace it your self, return the unit
to your local HSS Hire Shop for a replacement.
ELECTRICAL SAFETY
GENERAL SAFETY To reduce the risk of electric shock, use a
suitable RCD (Residual Current-Operated Device)
available from your local HSS Hire Shop, or power 240V
(not 110V) equipment from a power circuit with a
built-in RCD.
Never carry or pull the equipment by its flex.
Ensure the power socket is switched OFF before
plugging into the power supply.
If using a transformer to provide power, ensure
that the total power load is less than 75% of the
units power rating.
Position lights with care – somewhere they won’t
easily be knocked and where they won’t dazzle
drivers, this can be as dangerous as darkness.
Festoon...
Remove the lamp lenses (twist and pull) and place
somewhere safe. Run the flex along the desired
route, taping or tying it in place at intervals along
its length.
Next, fit each bulb-holder with one of the 60W
light bulbs supplied and replace the lamp lens.
Inspection Lamp...
Uncoil the light’s flex, hook the lamp onto a
suitable support and point in the requ-
ired direction.
Coil excess lead neatly but loosely, close to the
power supply and away from the work area where
people can’t trip over it.
All that now remains is to plug the light into its power
supply, switch ON and check that it works as it
should. In case of difficulty, contact your local HSS
Hire Shop.
GETTING STARTED
Tool or
Lead RCD Transformer Supply
Siting an RCD
When used with a transformer an RCD will only
protect the user if fitted between the transformer and
the tool being used.
An RCD fitted between the power supply and the
transformer only protects up to the transformer.
Lamp Lens
Tie-in or Tape
Festoon Light