HTC HRT-68 User manual

OPERATORS MANUAL
Date Purchased :
Where Purchased :
Address :
U.S. Patent No. 4,715,488
Assembly • Operation • Parts List • Warnings • Warranty
Caution: Read all instructions carefully.
SAVE THESE INSTRUCTIONS.
Refer to them often and use them to instruct others.
MODELS
HRT-68
HRT-70
HRT-88
HRT-90
Roller Table
Assembly
Instructions

Congratulations
You have just purchased a shop accessory that will help you work
safer, quicker, and easier than ever before. Designed for a lifetime of
use, HTC Products will help you do your best alone!
Roller Tables
Model Width Length # Rollers
HRT-68 15" 66" 9
HRT-70 15" 66" 17
HRT-88 24" 66" 9
HRT-90 24" 66" 17
HRT-68
HRT-70
HRT-88
HRT-90
Folds up quickly
for storage or transport.



Leg
Brace
Open Side
of Wedge


Leg
Brace Cross
Member
Leg
Clip
Top of Table
Wedge
Roller
Frame
Hinge
(Table Shown Upside Down) Roller
Cross
Member
Open Side
of Wedge
Hinge
Wedge
Roller
Frame
Cross
Member
Open Side
of Wedge
Roller
Figure 1 Figure 2
Figure 5
Figure 4
Figure 3

Safety Rules
Using power tools of any kind can be dangerous if safe operating pro-
cedures are not followed. Recognizing the hazards of each tool and
using them with respect and caution will considerably limit the possibil-
ity of personal injury. However, if safety precautions are ignored, per-
sonal injury will likely result. Always use common sense – your personal
safety is your responsibility.
1. Know your power tool. Read and understand the Owner’s Manual
and observe the warnings and instruction labels affixed to the tool.
2. Properly ground all tools.
3. Keep guards in place.
4. Remove adjusting keys and wrenches.
5. Keep work area clean and dry.
6. Keep children away.
7. Never leave running machines/tools unattended.
8. Disconnect tools from service.
9. Regularly maintain tools.
10. Use correct tools for the job.
11. Never force a tool.
12. Wear safety apparel.
13. Wear safety glasses/goggles.
14. Never stand or sit on tools.
15. Replace damaged components immediately.
16. Think Safety. Safety is a combination of operator awareness, common
sense and alertness at all times.
Assembly Instructions
1. Identify all components and hardware.
2. Remove inner leg wedge , and mount leg brace as shown in
Figure 1. The hinge pin positioning is an important assembly ele-
ment. The pin must be oriented as in Figure 1 for the unit to fold
correctly. The hinge mounts to the inside face on the open side of
the wedge. Use (2) 10-24 x 1/2" button head bolts and (2) 10-24
keps nuts.
3. Insert inner leg wedge into outer leg . Open side of the
wedge should face the same direction as the open side of the
outer leg.
4. Place the roller frame  upside down on a level surface and
mount the leg clips . The clips mount in the top holes of the
center cross-members as the frame is currently oriented (see
Figure 2). This will put them on the bottom of the frame when the
unit is in the upright position. Use (2) 10-24 x 1/2" button head
bolts and (2) 10-24 keps nuts.

Description Part HRT HRT HRT HRT
No. 68 70 88 90
15" Roller Frame 1 1 – –
24" Roller Frame – – 1 1
Wedge 5020 2 2 2 2
Outer Leg 5021 2 2 2 2
Brace 5022 2 2 2 2
Leg Clip 2298 2 2 2 2
Crank Handle 2459 2 2 2 2
13" Roller 2032 9 17 – –
22" Roller 2440 – – 9 17
Hinge 2294 2 2 2 2
Glide G209A 4 4 4 4
#10-24 x 1/2" Button Head Bolt 28 28 28 28
#10-24 Keps Nut 28 28 28 28
Parts List:
Various Style Roller Tables
5. Attach loose leaf leg hinge to inner leg wedge . Orient so
when the leg is in an upright position (as the leg would be during
use) the unsecured 1/2 of the hinge hangs down. Flat side of
hinge should be toward the wedge. Pin side of the hinge facing
out, or away from wedge. Secure with (4) 10-24 x 1/2" button
head bolts and (4) 10-24 keps nuts. Feed the bolts through the
hinge first.
6. Fold the leg brace in half and lay the leg assembly onto the roller
frame. Orient so the unsecured 1/2 of the hinge hangs down and
inline with the holes in the roller frame cross-member. Secure the
hinge to the roller frame with (4) 10-24 x 1/2" button head bolts
and (4) 10-24 keps nuts. Figure 4.
7. Tip the unit onto its side and swing the legs into their vertical posi-
tion. Attach the unsecured ends of the leg braces to the center
cross-member of the roller frame. DO NOT ATTEMPT TO ATTACH
THESE WITH THE FRAME UPSIDE DOWN! The leg could slam
into the closed position causing an injury. Secure with (2) 10-24 x
1/2" button head bolts and (2) 10-24 keps nuts. Figure 2.
8. Install the (4) adjustable glides into the threaded bosses of
the legs.
9. Turn the assembled unit upright and install the rollers using the
flat blade of a putty knife like a shoehorn. The spring axles will
snap into place.
Warning:
Read Owners Manual carefully and be completely familiar
with the correct and safe operation of each power tool
before use. Failure to follow these rules may result in serious
personal injury.

HTC Products, Inc.
P.O. Box 839
Royal Oak, MI 48068-0839
800-624-2027 © Copyright 2005 HTC Products, Inc. Part # 056
Limited Lifetime
Warranty
Warranty Card must be returned for validation.
Products manufactured by HTC Products, Inc. are guaranteed to
be free from defects in material and workmanship under normal
use and service. HTC’s obligation under this Warranty shall be lim-
ited to repairing or replacing, at our option, any part of said equip-
ment which HTC’s examination shall disclose to its satisfaction to
be thus defective.
All repairs and replacement parts furnished under this warranty
shall be F.O.B. point of distribution, but the owner must pay the
necessary freight, delivery charges and labor costs involved. Any
Federal, State or Local taxes are also extra.
This is a limited lifetime warranty provided that the attached regis-
tration card is properly filled out and returned to HTC Products, Inc.
This Warranty does not apply to damages resulting from shipping,
accident, misuse, abuse or alteration.
Your satisfaction is very important to us.
Please return your warranty card
with comments or suggestions.
Customer Service Department
800-624-2027