Htzsafe 805A User manual

1
Wireless Alarm System
User Manual
1. System Components And Usage
Note:
1.The alarm system has been programmed already,please
operate the system according to the part 2 of the manual;
2.If you want to add additional sensors to the system,
please operate the system according to the part 3 of the
manual or contact us directly.
Plug-in Receiver
Power Plug:plug the receiver into an outlet
Volume
Melody
Indicator Light
Power Plug
Volume: 4 adjustable volume levels
Melody: 35 optional classic melodies
Indicator Light: flashes for several seconds when the sensor
is activated
1 piece
1 piece
Plug-in Receiver
English Manual
Solar Wireless Motion Sensor 1(includes 1 set installation accessories) piece
Spare Charging Cord 1 piece( )not includes the USB plug
1. Configuration List

Solar Wireless Motion Sensor
Sensor Eye
2
Speaker
Speaker:sounds for several seconds when the sensor
is activated
Sensor Eye: detects heat movements
Solar Panel:charges the built-in battery of the sensor
Solar Panel
ON/OFF
Charge Jack
Charge Jack:used to connect the additional solar panel
or DC 5V power adapter
ON/OFF:sensor on/off
Drain Hole:used to drain out the rainwater(please note the
drain hole must be facing down when you install the sensor)
Drain Hole

3
Charge Jack
The KIT includes a USB charging cord(only the cord,
not the USB plug),which is used to charge the solar
wireless motion sensor before use or after pro-longed
low light conditions causing low battery.
Please kindly connect the charging cord with your
own USB plug(such as the direct USB outlet,
the phone's USB plug or computer's USB, etc.).
If needed,please charge the sensor for 4 hours
with the USB charging cord as below:
ATTENTION PLEASE
direct USB outlet
phone's USB plug
computer's USB

2. Operation Instructions
Step 1
Plug the receiver into an outlet
Step 2
The indicator light of the receiver will flash
for 15 seconds meaning normal operation
Turn on the Wireless Motion Sensor:
Press the ON/OFF button 4 times
(bleep prompt meaning normal operation)
ON/OFF
( )press 4 times
4

5
(the light of the ON/OFF button will flash
once meaning the motion sensor was activated
and sent the wireless signal;then the motion
sensor will automatically reset after
a few seconds ready for next trigger)
1 foot waya
Step 3
Activate The Wireless Motion Sensor
(wait about 30 seconds after you turn on the sensor)
1st method:press the ON/OFF button twice
(the light of the ON/OFF button will flash once meaning
the motion sensor was activated and sent the wireless signal)
ON/OFF
( twice)press
2nd method: Ensure the sensor is turned away from you.
and walk through in front of the sensor to acivate

6
Step 4
total 35 optional melodies.
Press “Melody” once to choose the melody for this sensor,
Melody
Wireless Motion Sensor
long screws
short screws
1
2
Step 6
Installation
3
Step 5
If you have additional sensors,please refer to 3.Other Settings

2.Please point the sensor towards a open field
(not towards the trees or bushes)
3.please adjust the sensor a little down(never upwards)
1. Please fix the motion sensor tightly to ensure the position
and the direction will not be moved easily by wind.
Installation Notes:
7
4.please point the sensor eye towards to the engine or exhaust
pipe if detecting vehicles.(the working principle of the
senor is detecting the movements with heat sources)

3. Other Settings
(1)How to add additional sensors to the receiver
(up to 32 sensors can be added to one or multiple receivers)
Step 1
Plug the receiver into an outlet
Step 2
Press and hold the “Volume” button for 5 seconds and release the
button when you hear a beep prompt and the indicator light flashes;
8
Volume
light up
press and hold the button
for 5 seconds
Volume
flashing slowly
release the button
Volume

Step 3
Note:please have the sensor close to the plug-in receiver
Activate the sensor.
Step 4
has been added to the receiver already.
Activate the sensor again to confirm the sensor
Step 5
total 35 optional melodies .
(2)How to delete the sensors of the receiver
Press”Melody”button to choose the melody for this sensor.
Step 1
Plug the receiver into an outlet
Step 2
Press and hold both the “Volume” button and “Melody”
button for 10 seconds and release the
buttons when you hear a long beep prompt;
Note: all the sensors will be deleted by this operation.
(a ring tone prompt and the indicator
light flashes quickly meaning the sensor
has been added to the plug-in
receiver successfully)
flashing quickly
Volume
Melody
9
ON/OFF
(twice)press
(the light of the ON/OFF button
will flash once meaning the motion
sensor was activated and sent
the wireless signal)

Step 1
Plug the receiver into an outlet
Step 2
Press the “Volume” once to adjust the volume of the receiver.
(total 4 adjustable volume levels)
(4)How to change the melody for the sensors
(total 35 optional melodies,you can match a different
melody for each sensor)
Step 1
Plug the receiver into an outlet
Step 2
Activate the sensor first,and then press the “Melody” button
to choose the melody for this sensor
Repeat steps for other sensors which have been added to
the receiver already.
10
Volume
(3)How to adjust the volume
(5)How to adjust the sensitivity of the sensor
The sensor has 3 adjustable sensitivities(Low,Medium,High)
Step 1
Turn off the sensor first
Press the ON/OFF button 3 times to turn off the sensor
(it will long beep prompt)

11
4. Technical Parameters
Plug-in Alarm Receiver
Technical parameters
Static Current 20mA; Alarming Current 300mA
Working Current
AC 110V-220V
433MHz FSK+FHSS
Technical Parameters
Working Voltage
Wireless Frequency
Item
80mm 48mm
86mm
34mm
Step 2
If select Low sensitivity---turn on the sensor by pressing
the ON/OFF button 3 times
If select Medium sensitivity---turn on the sensor by pressing
the ON/OFF button 4 times
If select High sensitivity---turn on the sensor by pressing
the ON/OFF button 5 times

27-201906-805A(1.1)T704(1.3)-06
103mm
92mm
Wireless Motion Sensor
45mm 90mm
Technical parameters
433MHz FSK+FHSS
Chargeable LiFePO4 Battery
3.3V
Low sensitivity--25feet(7.5m)
Mid sensitivity--30feet(9m)
High sensitivity--50feet(15m)
Technical Parameters
500mAh
Static: 1mA; Alarming:60mA
≥100mA in Sunny days
1/4 Mile(400m)
-22°F to 158°F(-30℃ to 70℃)
15
Detection Range
Item
Wireless Transmission Range
Wireless Frequency
Working Voltage
Battery Type
Battery Capacity
Working Current
Solar Panel Output Current
Working Temperature Range
Detection Angle
12