Htzsafe T804 User manual

1Wireless Alarm SystemUser Manual1. System Components And Usage Plug-in ReceiverVolumeMelodyPower PlugNote:[email protected]1.The alarm system is pre-programmed , please proceed to part 2 of the manual for setup. (Or please search “HTZSAFE T804&808A SETUP“ on YouTube, there is a video for your reference.)2.If you want to add additional HTZSAFE sensors/receivers to the system, program them according to part 3 of the manual or contact us directly. (Or please search “HTZSAFE T804 to 808A Connect “ on YouTube, there is a video for your reference.)After-sale Service:E-mail:Indicator Light

Wireless Motion SensorSensor EyeSpeakerSpeaker:sounds for several seconds when the sensor is activated.Sensor Eye: detects heat movements.Power Plug:plug the receiver into an outlet.Volume: 4 adjustable volume levels.Melody: 35 optional melodies.Indicator Light: flashes for several seconds when the sensor is activated/flashes once each 8 seconds if the battery of the sensors go flat.2

3Indicator LightBattery CompartmentIndicator Light: flashes once meaning the motion sensor was activatedand sent the wireless signal.Battery Compartment: please insert 3 pieces AA 1.5V Alkaline batteries (not included).Sensitivity Jumper : Factory default is Low sensitivity, if you want to select High sensitivity, please take out the jumper slightly by the plier first, and insert the jumper back to the left two needles.Sensitivity Jumper2. Operation InstructionsStep 1Plug the receiver into an outlet.The indicator light of the receiver will flash onceand a beep prompt meaning normal operation.

1.take out the jumper
high2.insert the jumper back to the left two needles.low4Step 3(Indicator lights will be on for 5 seconds meaning work properly,and wait about 30 seconds to activate the sensor.)Insert the 3pcs AA 1.5V Alkaline Batteries and note the anode and cathode (Batteries are not included).Step 2Select the sensitivity (High / Low)Factory default is Low sensitivity,if you want to select High sensitivity, please take out the jumper slightly by the plier first, and insert the jumper back to the left two needles as bellow:If High sensitivity, the detection range of the sensor is 50 feet;If Low sensitivity, the detection range of the sensor is 35 feet.(Or please search "T804 Sensitivity Setup" on YouTube,there is a video for your reference)

5Step 4Wave your hands in front of the sensor eye to activate.(the indicator light of the sensor will flash once meaning the sensor was activated,and then the sensor will automatically reset after a few seconds ready for next trigger.)1 foot wayaStep 5Fix the back cover ( the back cover must be fixed well to ensure the waterproof if the sensor is installed outdoor).

Step 7Same operation if you have the additional sensor,and please refer to part 3 of the manuel for other settings.Step 8Installation.Wireless Motion SensorStep 6total 35 optional melodies.Press “Melody” once to choose the melody for this sensor, Melody6long screwsshort screws123

2.Please point the sensor towards a open field(not towards the trees or bushes).3.please adjust the sensor a little down(never upwards).1.Please fix the motion sensor tightly to ensure the position and the direction will not be moved easily by wind.4.please point the sensor eye towards to the engine or exhaust pipe if detecting vehicles.(the working principle of the senor is detecting the movements with heat sources).Installation Notes:7

Step 3Note:please have the sensor close to the plug-in receiver.Activate the sensor.flashing slowlyrelease the buttonVolume(1)How to add additional sensors/receivers to the system(up to 32 sensors can be added to one or multiple receivers)Step 1Plug the receiver into an outlet.Step 2Press and hold the “Volume” button for 5 seconds and release thebutton when you hear a beep prompt and the indicator light flashes.3. Other Settings8Volumelight uppress and hold the button for 5 secondsVolume

Step 1Plug the receiver into an outlet.Step 2Press and hold both the “Volume” button and “Melody” button for 10 seconds and release the buttons when you hear a long beep prompt;Note: all the sensors will be deleted by this operation.VolumeStep 4has been added to the receiver already.Activate the sensor again to confirm the sensor Step 5total 35 melodies optional.(2)How to delete the sensors of the receiverPress”Melody”button to choose the melody for this sensor. flashing quickly(a ring tone prompt and the indicatorlight flashes quickly meaning the sensor has been added to the plug-in receiver successfully)Melody
1 foot waya
9(the indicator light will flash oncemeaning the motion sensor was activated and sent the wireless signal)

Volume 61mm 45mm(4)How to change the melody for the sensors (total 35 optional melodies; you can match different melody for each sensor.)Step 1Plug the receiver into an outlet.Step 2Activate the sensor first,and then press the “Melody” button to choose the melody for this sensor.Repeat steps for other sensors which have been added to the receiver already.104. Technical ParametersPlug-in Receiver81mm87mmStep 1Plug the receiver into an outlet.Step 2Press the “Volume” once to adjust the volume of the receiver (total 4 adjustable volume levels).(3)How to adjust the alarm volume

11Technical parameters
Static Current 20mA; Alarming Current 300mA
Working Current
AC 110V-220V
433MHz FSK+FHSS
Technical Parameters
Working VoltageWireless Frequency
Item30-HB202011-808A(2.2)T804(1.1)-0375mm 100mmWireless Motion Sensor65mm 30mmTechnical parametersDetection RangeItemWireless Transmission RangeWireless FrequencyWorking VoltageBattery Type433MHz FSK+FHSS
3pcs AA 1.5V Batteries(not )Alkaline included
4.5VLow sensitivity----35 feet(10m)High sensitivity----50 feet(15m)Technical ParametersWorking CurrentStatic≤1mA; Alarming≤100mAWorking Temperature Range1/2 Mile (800m) -22°F to 158°F（-30℃ to 70℃)Detection Angle15°