Huawei NE05E User manual

HUAWEI TECHNOLOGIES CO., LTD.
NE05E&NE08E Series Mid-End Router
Quick Installation Guide
(APM30H Cabinet)
Issue: 02
Date: 2016-06-30

Copyright © Huawei Technologies Co., Ltd. 2016. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior
written consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and
the customer. All or part of the products, services and features described in this document may not be
within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,
information, and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Huawei Technologies Co., Ltd.
Address:
Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website:
http://www.huawei.com
Email:
[email protected]

0
Installation Flow
PrecautionsPage 1
Tools for InstallationPage 2
Introduction to the 1U-
height Chassis
Pages
3-4
Installation Scenarios of
NE Equipment
Page 7
Connecting and Routing
Cables
Pages
12-16
Installation Checklist
End
Start
Checking Tail Fiber
Connection
Page 20
Powering On the
Equipment
Pages
18-19
Preparation
for
installation
Page 17
Introduction to the 2U-
height Chassis
Page 5
Installing the Assemblies
Pages
8-11
Powering On the
Equipment
Pages
18-20
Introduction to the
APM30H Cabinet
Page 6
Installing the NE
Equipment in the APM30H
Cabinet
Installing the SLPU
(Optional)
Page 8
Page 9
Installing the SOU in the
APM30H Cabinet (Optional)
Installing the Heater in the
APM30H Cabinet (Optional)
Page 10
Page 11
Paint Repair
Applying Grease to the
Required Position
Page 24
Page 25
Assembling OT Terminals
Page 23
Assembling the Easy Power
Receptacle (Pressfit Type)
Connector
Page 22
Layout of the Cable Holes
Page 21
Appendixes
Pages
21-25
Connecting the Power
Cables
Connecting the Service
Cables for the Equipment
Pages
13-14
Pages
15-16
Common Cables for the
Chassis
Page 12
Cabinet Sharing
Separate Outdoor
Installation
Page 7
Page 7
Connecting the PGND
Cables
Page 12

1
Precautions
This document provides simple and distinctive guidelines for quick hardware installation of the
NE05E&NE08E(NE05E-S2/SE/SF/SG/SH/SI/SQ&NE08E-S6/S6E).
Based on the height of a device, the NE05E-S2/SE/SF/SG/SH/SI/SQ are considered 1 U devices,
and the NE08E-S6/S6E are considered 2 U devices. 1 U = 44.45 mm (1.75 in.)
As the installation methods are similar, the fixed NE05E-SF is used as an example for the 1 U
device, and the card-inserted NE08E-S6 is used as an example for the 2 U device. The installation
differences are specially described in this document.
This document does not describe pre-delivery assembly. This document only describes procedures
for onsite installation.
Wear ESD gloves or Antistatic Wrist Strap prior to
contact with the equipment or before handling the
plug-boards, boards, and IC chips to prevent damage
to sensitive components caused by electrostatic
discharge from the human body.
Binding intervals between cable ties or optical fiber binding straps inside the cabinet cannot
exceed 250 mm.
Bundling cables
Electrostatic Discharge
Pre-Installation Check
Verify that the equipment room, power supply, ground cables and optical cables are ready for
installation. Start the installation according to the engineering design documents after confirming
that conditions are met. Refer to the Installation Guide for information about specific operational
requirements and technical specifications.
NOTE
CAUTION
CAUTION
CAUTION

2
Tape Measure Philips Screwdriver
（M2-M6) Flathead Screwdriver
（M2-M6)
Adjustable Wrench
Level Bar
Ratchet Crimp Tool Cable Cutter
Wire Stripper
Network Cable
Crimping Pliers Diagonal Pliers
Sharp-nose Pliers
Paper Knife
Marker Pen
Electric Iron
Heat Gun Multimeter
ESD Gloves Binding Strap Insulation Tape Antistatic Wrist Strap
Punching Wire pliers
Vacuum cleaner
Tools for Installation
Cable Tester Optical Power Meter BER Tester
Coax Stripper

3
NE05E-S2
Introduction to the 1U-height Chassis
Clock interface
Power supply interface
Time interface
NM interface
(Console interface)
Alarm interface
PGND point
FE/GE electrical interface
10GE optical interface
FE/GE optical interface
E1 interface
Alarm interface
PGND pointPower supply interface
GE optical interface
Clock and time interface
T1 interface
Antistatic jack interface
FE/GE electrical interface SHDSL interface
NE05E-SE/NE05E-SF
10
10
10
NM interface
(Console interface)
FE/GE optical
interface
10
10

4
NE05E-SG/NE05E-SH/NE05E-SI/NE05E-SQ
Clock interface
Power supply interface
Time interface
NM interface
(Console interface)
PGND point
Electrical interface
GE optical interface
Alarm interface
E1 interface
10
10
FE/GE optical interface
FE/GE optical interface FE/GE electrical interface
Power supply interface Clock interface
10GE optical interface
Antistatic jack interface
Time interface
NM interface
(Console interface) Alarm interface
For running an AC NE05E-SQ, you must turn on the switches of both AC power modules operating
in 1+1 backup mode.
NOTE

5
NE08E-S6
Introduction to the 2U-height Chassis
10
Alarm interface PGND point
Power supply interface
GE optical interface
Clock interface
Time interface
Antistatic jack interface
E1 interface
NM interface
(Console interface)
Electrical interface
10
NE08E-S6E
Alarm interface PGND point
Power supply interface
GE optical interface
Clock interface
Time interface
Antistatic jack interface NM interface
(Console interface)
Electrical interface
10
10
10GE optical interface

6
APM30H机柜介绍
Technical Specifications
•Dimensions:700 (H) x 600 (W) x 480 (D)
•Ambient temperature: -40°C to +50°C
•Sunshine radiation: 1120±10%W/m2
•Allowable heat dissipation:≤700 W
The Internal Structure of the APM30H Cabinets
Introduction to the APM30H Cabinet
View of the APM30H Cabinet
HPMI board Fan board (internal circulating) CMUA board PSU module
EPS frame PMU module Cable distribution box

ATN950B
ATN950B
7
Installation Scenarios of NE Equipment
1 Cabinet Sharing
Installing NE equipment in the APM30H cabinet together with BBU
a
Heater
NE05E-SF
Power supply
system
Fan unit
BBU
5U
2U
5U
SLPU
2 Separate Outdoor Installation
Installing the NE equipment in the APM30H Cabinet
a
7U
SOU
Heater
NE05E-SF
SLPU
Power supply
system
Fan unit
1U-height chassis 2U-height chassis
Heater
NE08E-S6
Power supply
system
Fan unit
BBU
SLPU
5U
2U
5U
7U
SOU
Heater
NE08E-S6
SLPU
Fan unit
Power supply
system
1U-height chassis 2U-height chassis
By default, the heater (optional) is installed in the lowest part of the cabinet. If cables connected to electrical
ports are led out of the cabinet, an SLPU must be installed.
NOTE
In the case of separate outdoor installation, the heater and SOU are optional. If cables connected to electrical
ports are led out of the cabinet, an SLPU must be installed.
NOTE