Huawei IDS2000 Dual-Row Aisle Containment User manual

IDS2000 Intelligent Micro-Modular Data Center
V500R001
Installation Guide (2000 mm
High Cabinet in Dual-Row Aisle
Containment)
Issue
Draft A
Date
2015-06-29
HUAWEI TECHNOLOGIES CO., LTD.

Issue Draft A (2015-06-29)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
i
Copyright © Huawei Technologies Co., Ltd. 2015. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior
written consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and
the customer. All or part of the products, services and features described in this document may not be
within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,
information, and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Huawei Technologies Co., Ltd.
Address:
Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website:
http://enterprise.huawei.com

IDS2000 Intelligent Micro-Modular Data Center
Installation Guide (2000 mm High Cabinet in Dual-Row
Aisle Containment)
About This Document
Issue Draft A (2015-06-29)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
ii
About This Document
Purpose
This document describes how to install the IDS2000 intelligent micro-module in the
double-row aisle containment scenario.
Intended Audience
This document is intended for:
Hardware installation engineers
Commissioning engineers
Maintenance engineers
Technical support engineers
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Symbol
Description
Indicates an imminently hazardous situation which, if
not avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
Indicates a potentially hazardous situation which, if not
avoided, could result in equipment damage, data loss,
performance deterioration, or unanticipated results.
NOTICE is used to address practices not related to
personal injury.
Calls attention to important information, best practices
and tips.

IDS2000 Intelligent Micro-Modular Data Center
Installation Guide (2000 mm High Cabinet in Dual-Row
Aisle Containment)
About This Document
Issue Draft A (2015-06-29)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
iii
Symbol
Description
NOTE is used to address information not related to
personal injury, equipment damage, and environment
deterioration.
Change History
Changes between document issues are cumulative. The latest document issue contains all
updates made in previous issues.
Issue Draft A (2015-06-29)
This issue is used for first office application (FOA).

IDS2000 Intelligent Micro-Modular Data Center
Installation Guide (2000 mm High Cabinet in Dual-Row
Aisle Containment)
Contents
Issue Draft A (2015-06-29)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
iv
Contents
About This Document.................................................................................................................... ii
1 Precautions .....................................................................................................................................1
1.1 General Safety Precautions...........................................................................................................................................1
1.2 Electrical Safety............................................................................................................................................................2
1.3 Battery ..........................................................................................................................................................................4
1.4 Mechanical Safety ........................................................................................................................................................6
1.5 Others ...........................................................................................................................................................................7
2 Installation Preparations .............................................................................................................8
2.1 Transportation Precautions ...........................................................................................................................................8
2.2 Unpacking and Acceptance...........................................................................................................................................9
2.3 Installation Environment Requirements .......................................................................................................................9
2.4 Site Requirements....................................................................................................................................................... 11
2.5 Documents..................................................................................................................................................................13
2.6 Tools and Instruments.................................................................................................................................................14
2.7 Personnel Requirements .............................................................................................................................................16
3 Scenario.........................................................................................................................................18
4 Hardware Installation ................................................................................................................20
4.1 Installation Flowchart.................................................................................................................................................20
4.2 Positioning Cabinets or Bases.....................................................................................................................................22
4.3 Installing Bases...........................................................................................................................................................23
4.3.1 Installation Flowchart..............................................................................................................................................23
4.3.2 Placing Bases...........................................................................................................................................................24
4.3.2.1 Deploying a 600 mm Wide Fixed Base ................................................................................................................24
4.3.2.2 Deploying an 800 mm Wide Fixed Base ..............................................................................................................25
4.3.2.3 Deploying a 600 mm Wide PDU8000 Base..........................................................................................................25
4.3.2.4 Deploying a 300 mm Wide Fixed Base ................................................................................................................27
4.3.3 Securing Bases.........................................................................................................................................................27
4.4 Routing and SecuringAir Conditioner Pipes..............................................................................................................30
4.4.1 Requirements ofAir Conditioner Pipe Connectors and Water Quality....................................................................30
4.4.2 Precautions for Routing and SecuringAir Conditioner Pipes..................................................................................32
4.5 Installing the Cabinet..................................................................................................................................................34

IDS2000 Intelligent Micro-Modular Data Center
Installation Guide (2000 mm High Cabinet in Dual-Row
Aisle Containment)
Contents
Issue Draft A (2015-06-29)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
v
4.5.1 Cabinet Installation Flowchart.................................................................................................................................34
4.5.2 Removing the Pallet from a 2000 mm High Cabinet...............................................................................................34
4.5.3 Placing the Cabinet..................................................................................................................................................35
4.5.4 Securing a Cabinet...................................................................................................................................................36
4.5.4.1 Securing a PDU8000 ............................................................................................................................................36
4.5.4.2 Securing a Server Cabinet.....................................................................................................................................37
4.5.4.3 Securing a NetCol5000-A020Air Conditioner.....................................................................................................38
4.5.5 Installing Adaptive Frames......................................................................................................................................41
4.5.5.1 Installing the PDU8000 Tail Frame......................................................................................................................41
4.5.5.2 Installing a 300 mm Wide Air ConditionerAdaptive Frame ................................................................................44
4.5.6 Combining Cabinets ................................................................................................................................................46
4.5.7 Installing Cabinet Accessories.................................................................................................................................47
4.5.7.1 Taking Out PDU2000 Industrial Connectors and Cables......................................................................................47
4.5.7.2 (Optional) Installing a Branch Ground Bar...........................................................................................................49
4.6 Installing the Contained Aisles ...................................................................................................................................50
4.6.1 Installation Flowchart..............................................................................................................................................50
4.6.2 Skylight Overview...................................................................................................................................................50
4.6.3 Installing Skylights..................................................................................................................................................54
4.6.4 Installing End Doors................................................................................................................................................59
4.6.4.1 Installing a Sliding Door.......................................................................................................................................60
4.6.4.1.1 Installing a Mounting Kit Under a SlidingAisle Door ......................................................................................60
4.6.4.1.2 Installing a Sliding Door in the 2000 mm Scenario...........................................................................................63
4.6.4.2 Installing a Double Revolving Door (Compatible withAccess Control Components).........................................70
4.6.4.2.1 Installing Aisle Door Fittings.............................................................................................................................70
4.6.4.2.2 Installing a Door Frame.....................................................................................................................................72
4.6.4.2.3 Installing Door Panels........................................................................................................................................75
4.6.4.2.4 Installing a Door Closer.....................................................................................................................................79
4.6.4.2.5 Installing Post Side Panels and Removing the Auxiliary Bar............................................................................83
4.7 Installing Cable Trays.................................................................................................................................................84
4.8 Installing Cable Troughs.............................................................................................................................................87
4.8.1 Installing a 600 mm Wide Cable Trough.................................................................................................................88
4.8.2 Installing a 300 mm Wide Cable Trough.................................................................................................................93
4.8.3 Installing an 800 mm Wide Cable Trough...............................................................................................................94
4.8.4 Installing End Panels for Cable Troughs .................................................................................................................94
4.9 (Optional) Installing theAccess Control System........................................................................................................95
4.9.1 Installing a Double-Door Magnetic Lock................................................................................................................96
4.9.2 Installing the Card Reader .....................................................................................................................................102
4.9.3 Installing an Access Controller..............................................................................................................................106
4.9.4 Installing Switches.................................................................................................................................................109
4.10 (Optional) Installing Aisle Lights ........................................................................................................................... 113
4.11 Installing Monitoring Devices ................................................................................................................................ 115
4.11.1 Device Layout in the Network Cabling Cabinet.................................................................................................. 115

IDS2000 Intelligent Micro-Modular Data Center
Installation Guide (2000 mm High Cabinet in Dual-Row
Aisle Containment)
Contents
Issue Draft A (2015-06-29)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
vi
4.11.2 Installing the Server............................................................................................................................................. 117
4.11.3 Installing a LAN Switch ...................................................................................................................................... 119
4.11.4 Installing an ECC Collector.................................................................................................................................121
4.11.5 (Optional) Installing the VCN500........................................................................................................................121
4.11.6 Installing a Skylight Controller............................................................................................................................122
4.11.7 Installing the Lighting Control Box.....................................................................................................................123
4.11.8 (Optional) Installing an STS Switch....................................................................................................................123
4.11.9 (Optional) Installing an Independent AI/DI Module............................................................................................124
4.11.10 Installing Monitoring Components on a Control Skylight.................................................................................124
4.11.10.1 Installing a Camera .........................................................................................................................................126
4.11.10.2 Installing a Smoke Sensor...............................................................................................................................129
4.11.10.3 Installing an Infrared Sensor...........................................................................................................................130
4.11.11 Installing Temperature Sensors..........................................................................................................................131
4.11.12 Installing the Audible and Visual Alarm............................................................................................................132
4.11.13 Installing a WLDS900 Water Detector ..............................................................................................................133
4.12 Cable Routing.........................................................................................................................................................136
4.12.1 System Cabling Rules..........................................................................................................................................136
4.12.2 Cable Routing for the Dual-row Aisle Containment Scenario.............................................................................141
4.12.3 Routing Cables for the Network Cabling Cabinet...............................................................................................142
4.12.4 Installation Positions for Monitoring Components..............................................................................................143
4.12.5 Cable Routing for the Door Monitoring Components .........................................................................................144
4.12.6 Cable Routing for the Sensors on the Control Skylight.......................................................................................145
4.12.7 Cable Routing for theAisle Lighting System......................................................................................................146
4.12.8 Cable Routes for Skylight Magnetic Locks.........................................................................................................148
4.12.9 Connecting Module Ground Cables.....................................................................................................................149
4.12.10 Cable Installation for the Power Supply and Distribution System.....................................................................152
4.12.10.1 Connecting Battery Cables .............................................................................................................................152
4.12.10.2 Cable Connections for Power Supply and Distribution Devices ....................................................................157
4.12.11 Connecting Cables for the Temperature Control System...................................................................................157
4.12.12 Installing Cables for the Equipment Room Management System .....................................................................157
4.12.12.1 Preparing a Monitoring Cable.........................................................................................................................157
4.12.12.2 Connecting the Server Monitoring Cable .......................................................................................................159
4.12.12.3 Installing the SMS Modem.............................................................................................................................159
4.12.12.4 Connecting the LAN Switch Monitoring Cable..............................................................................................161
4.12.12.5 Connecting a Monitoring Cable to the ECC Collector ...................................................................................162
4.12.12.6 (Optional) Connecting a Monitoring Cable to the VCN500...........................................................................162
4.12.12.7 Connecting a Monitoring Cable to a Lighting Control Box............................................................................163
4.12.12.8 Connecting a Monitoring Cable to the Skylight Controller............................................................................165
4.12.12.9 Connecting anAccess Controller Monitoring Cable ......................................................................................167
4.12.12.10 Connecting a Monitoring Cable to a Camera................................................................................................170
4.12.12.11 Connecting a Monitoring Cable to a Door Status Sensor..............................................................................170
4.12.12.12 Connecting a Monitoring Cable to a Smoke Sensor.....................................................................................171

IDS2000 Intelligent Micro-Modular Data Center
Installation Guide (2000 mm High Cabinet in Dual-Row
Aisle Containment)
Contents
Issue Draft A (2015-06-29)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
vii
4.12.12.13 Connecting a Cable to the WLDS900 Water Detector..................................................................................172
4.12.12.14 Connecting a Cable to a Temperature Sensor ...............................................................................................172
4.12.12.15 Connecting a Monitoring Cable to the MS899 Electronic Lock...................................................................173
4.12.12.16 Connecting a Monitoring Cable to a PDU2000............................................................................................173
4.12.12.17 Connecting the NetCol5000-A020 Monitoring Cable..................................................................................174
4.12.12.18 Connecting PDU8000 Monitoring Cables....................................................................................................176
4.13 (Optional) Installing Base Decorative Plates..........................................................................................................177
4.14 Installing Cabinet Sealing Plates ............................................................................................................................178
5 Checking the Installation ........................................................................................................180
6 Power-On Commissioning......................................................................................................181
6.1 Power-on Commissioning Process ...........................................................................................................................181
6.2 Commissioning the Power Supply and Distribution System....................................................................................182
6.3 Commissioning the Temperature Control System ....................................................................................................182
6.4 Configuring the Facility Management System .........................................................................................................183
A Appendix ...................................................................................................................................185
A.1 (Optional) Connecting Linkage Cables Between the Gas Extinguishing Controller andATS.................................185
A.2 (Optional) Connecting the Linkage Cables Between the Fire Extinguishing System and Access Controller..........187
A.3 Introduction to ECC Ports........................................................................................................................................188
A.4 Ports on the Skylight Controller ..............................................................................................................................190
B Checking the Installation........................................................................................................193
C Acronyms and Abbreviations................................................................................................196

IDS2000 Intelligent Micro-Modular Data Center
Installation Guide (2000 mm High Cabinet in Dual-Row
Aisle Containment)
1 Precautions
Issue Draft A (2015-06-29)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
1
1 Precautions
This section provides the safety precautions for installing, operating, and maintaining modular
data center equipment.
1.1 General Safety Precautions
This section describes safety precautions to be taken when installing, operating, and
maintaining intelligent micro-module equipment.
Overview
To ensure safety of humans and the equipment, pay attention to the safety symbols on the
equipment and all the safety instructions in this document.
The "NOTICE", "WARNING", "CAUTION", and "DANGER" marks in this document do not
represent all the safety instructions. They are only supplements to the safety instructions.
Local Safety Regulations
When operating the equipment, you must follow local laws and regulations. The safety
instructions in this document are only supplements to the local laws and regulations.
Personal Requirements
Only trained and qualified personnel are allowed to install, operate, and maintain Huawei
equipment, and they must understand basic safety precautions to avoid hazards.
Only trained and qualified personnel are allowed to install, operate, and maintain the
equipment.
Only trained and qualified personnel are allowed to remove safety facilities and inspect
the equipment.
Only personnel certified or authorized by Huawei are allowed to replace or change the
equipment or components (including software).
Installation personnel must report faults or errors that might cause serious safety issues
to related owners.

IDS2000 Intelligent Micro-Modular Data Center
Installation Guide (2000 mm High Cabinet in Dual-Row
Aisle Containment)
1 Precautions
Issue Draft A (2015-06-29)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
2
Grounding Requirements
Equipment to be grounded must meet the following requirements:
When installing the equipment, always ground the device first. Disconnect the ground
cable at the end of removing the device.
Do not damage the ground conductor.
Do not operate the device in the absence of a properly installed ground conductor.
Conduct the electrical inspection carefully.
The device (or system) must be connected permanently to the protection ground before
an operation. Before operating the device, check the electrical connection of the device
to ensure that it is securely grounded.
Human Safety
Before operating a device, wear electrostatic discharge (ESD) clothes, ESD gloves, and
an ESD wrist strap. Do not wear jewelry or watches when you operate the device.
In the case of fire, immediately leave the building or the equipment room, and turn on
the fire alarm bell or make an emergency call. Do not enter a building that is on fire.
Equipment Safety
The device must be fixed securely on the floor or to other immovable objects such as
walls and mounting racks before operation.
Do not block the ventilation vents while the system is operating.
Tighten the thumbscrews by using a tool after initial installation and subsequent access
to the panel.
After the installation, remove packing materials from the equipment area.
1.2 Electrical Safety
This section describes the precautions to be taken in terms of electrical safety.
High Voltage
Devices are powered by high-voltage power source. Direct or indirect contact (through
damp objects) with the power source may result in serious injury.
Non-standard and improper operations under high voltage may result in fire and electric
shocks.
High Electrical Leakage

IDS2000 Intelligent Micro-Modular Data Center
Installation Guide (2000 mm High Cabinet in Dual-Row
Aisle Containment)
1 Precautions
Issue Draft A (2015-06-29)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
3
Ground the device before powering it on. Otherwise, personal injury or device damage may
be caused by high leakage current.
If a "high electrical leakage" tag is present on the power terminal of the device, you must
ground the device before powering it on.
Power Cable
Do not install or remove power cables when the device is on. Transient contact between the
core of the power cable and the conductor may generate electric arcs or sparks, which may
cause fire or hurt human eyes.
Before installing or removing the power cable, turn off the power switch.
Before connecting a power cable, verify that the label on the power cable is correct.
Electrostatic Discharge
The static electricity generated by human bodies may damage the electrostatic-sensitive
components on boards, for example, the large-scale integrated (LSI) circuits.
Human body movement, friction between human bodies and clothes, friction between
shoes and floors, or handling of plastic articles causes static electromagnetic fields on
human bodies. These static electromagnetic fields cannot be eliminated until the static is
discharged.
To prevent electrostatic-sensitive components from being damaged by the static on
human bodies, you must wear a well-grounded ESD wrist strap when touching the
device or handling boards or application-specific integrated circuits (ASICs).
Figure 1-1 shows how to put on an ESD wrist strap.

IDS2000 Intelligent Micro-Modular Data Center
Installation Guide (2000 mm High Cabinet in Dual-Row
Aisle Containment)
1 Precautions
Issue Draft A (2015-06-29)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
4
Figure 1-1 Putting on an ESD wrist strap
1.3 Battery
This section describes precautions for operating batteries.
Before operating batteries, carefully read the safety precautions for battery handling and
connection.
Incorrect handling of batteries causes hazards. When operating batteries, avoid battery
short circuits and electrolyte overflow or leakage.
Electrolyte overflow may damage the device. It will corrode metal parts and circuit
boards, and ultimately damage the device and cause short circuits of circuit boards.
Short circuits caused by incorrect operations may cause serious injuries due to high
power of batteries.
Preventative Measures
When installing and maintaining batteries, pay attention to the following points:
Use special insulation tools.
Take care to protect your eyes when operating batteries.
Wear rubber gloves and a protective coat in case of electrolyte overflow.
When moving a battery, ensure that its electrodes are upward. Leaning or reversing the
battery is prohibited.
Switch off the power supply during installation and maintenance.
Short Circuit

IDS2000 Intelligent Micro-Modular Data Center
Installation Guide (2000 mm High Cabinet in Dual-Row
Aisle Containment)
1 Precautions
Issue Draft A (2015-06-29)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
5
Battery short circuits may cause human injuries. Although the voltage of ordinary batteries is
low, the instantaneous high current caused by the short circuit releases a great deal of energy.
To avoid battery short circuits, do not maintain batteries in use.
Harmful Gas
Do not use unsealed lead-acid batteries. Place and secure lead-acid batteries horizontally to
avoid inflammation or device corrosion due to flammable gases emitted from batteries.
The lead-acid batteries in use may emit flammable gases. Therefore, store the batteries in a
place with good ventilation, and take precautions against fire.
Battery Temperature
High temperature may result in battery distortion, damage, and electrolyte overflow.
Install or store batteries far away from fire and heating sources, such as transformers.
Never burn batteries.
When the temperature of the battery is higher than 60°C, check the battery for electrolyte
overflow. If the electrolyte overflows, absorb and counteract the electrolyte immediately.
Acid leakage
In the case of electrolyte leaks, counteract and absorb the leaking electrolyte immediately.
When moving or handling a battery whose electrolyte leaks, note that the leaking electrolyte
may hurt human bodies. When you find the electrolyte leaks, use the following substances to
counteract and absorb the leaking electrolyte:
Sodium bicarbonate (baking soda): NaHCO3
Sodium carbonate (soda): Na2CO3
When using substances to counteract and absorb electrolytes, strictly follow the guidelines
provided by the battery supplier.

IDS2000 Intelligent Micro-Modular Data Center
Installation Guide (2000 mm High Cabinet in Dual-Row
Aisle Containment)
1 Precautions
Issue Draft A (2015-06-29)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
6
If your body meets the acid, wash the part that has met the acid with clean water immediately,
or immediately call a doctor if the situation is serious.
1.4 Mechanical Safety
This section describes the precautions be taken when moving sharp and heavy objects.
Drilling Holes
Do not drill holes on the rack without permission. Non-standard drilling may deteriorate
electromagnetic shielding performance and damage the internal cables, and metal scraps
generated during drilling may short-circuit a circuit board.
Before drilling holes on the rack, first remove the cables inside the rack.
To protect your eyes from metal shavings, wear a pair of goggles when drilling holes.
Before drilling holes, wear protective gloves.
After drilling, clean up the metal shavings.
Moving Sharp Objects
Wear protective gloves when moving sharp objects.
Fan
When replacing a component, place the component, screws, and tools in a safe place.
Otherwise, if any of them fall into the operating fans, the fans may be damaged.
When replacing a component near fans, do not insert your fingers or boards into the
operating fans until the fans are switched off and stop running.
Moving Heavy Objects
Wear protective gloves when moving heavy objects.

IDS2000 Intelligent Micro-Modular Data Center
Installation Guide (2000 mm High Cabinet in Dual-Row
Aisle Containment)
1 Precautions
Issue Draft A (2015-06-29)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
7
Be careful to prevent injury when moving heavy objects.
To prevent injury, when moving the chassis outwards, be aware of unfixed or heavy
objects on the chassis.
At least two persons are required to move the chassis. When lifting it, keep your back
straight and move smoothly to avoid injury.
Move or lift the chassis by holding its lower edge. Do not hold the handles on certain
modules such as power supply, fans, and boards because they cannot support the weight
of the device.
1.5 Others
This section describes the precautions to be taken when binding signal cables and laying out
power cables at a low temperature.
Binding Signal Cables
Signal cables must be bound separately from strong-current cables and high-voltage cables.
Routing Power Cables
When the temperature is low, violent strike or vibration may damage the cable sheathing. To
ensure safety, comply with the following requirements:
Cables can be laid or installed only when the temperature is higher than 0°C.
Before laying out power cables which have been stored in a temperature lower than 0°C,
move the power cables to an environment of the ambient temperature and store them at
the ambient temperature for at least 24 hours.
Handle cables with caution, especially at a low temperature. Do not drop the cables
directly from the vehicle.

IDS2000 Intelligent Micro-Modular Data Center
Installation Guide (2000 mm High Cabinet in Dual-Row
Aisle Containment)
2 Installation Preparations
Issue Draft A (2015-06-29)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
8
2 Installation Preparations
2.1 Transportation Precautions
Air Conditioner Transportation Precautions
Only trained personnel are allowed to move the cabinet. Use a pallet truck to transport
the cabinet secured to a wooden support to the installation position. Insert the forks of
the pallet truck in the middle position to ensure balance.
Choose the rail, sea, or good road for transportation. Avoid excessive vibration or tilting
during transportation. When loading and unloading the cabinet, keep the gradient within
15 degrees, as shown in Figure 2-1.
To prevent the cabinet from falling over, secure it to a pallet truck using ropes before
moving it.
To prevent shocks or falls, move the cabinet gently.
After placing the cabinet in the installation position, unpack it and take care to prevent
scratches. Keep the cabinet steady during unpacking.
Figure 2-1 Transportation Gradient

IDS2000 Intelligent Micro-Modular Data Center
Installation Guide (2000 mm High Cabinet in Dual-Row
Aisle Containment)
2 Installation Preparations
Issue Draft A (2015-06-29)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
9
2.2 Unpacking and Acceptance
Context
Unpack and inspect all cabinets, mechanical parts, and components. Check that all the items
are intact and comply with the packing list on the presence of both the project supervisor and
customer.
Procedure
Step 1 Unpack the carton labeled "Contain Packing List" and take out the Packing List.
Step 2 Check all items against the Packing List.
Step 3 If shortage or miscarriage occurs, fill in the Cargo Shortage and Miscarriage Report.
Step 4 If cargo damage occurs, fill in the Cargo Replacement Application Form.
Place the cartons in order, with the marked sides facing the same direction.
Step 5 Sign on the Packing List with the customer after verifying that all required items are
delivered.
Step 6 Store the items properly.
----End
Follow-up Procedure
Put the items to be installed immediately onto an ESD surface, such as a polyethylene (PE)
bag or an expandable polyethylene (EPE) foam. Pack the items not to be installed
immediately with their original packing materials. Put them in a dry and cool environment
without exposure to sunlight or electromagnetic radiation.
2.3 Installation Environment Requirements
Ensure that the installation environment meets the requirements before installation.
Table 2-1 Installation environment checklist
Check Item
Requirement
Check Result
Floor bearing
capacity
Standard live load of the equipment room:
8–12 kN/m2(If the battery cabinet is
contained in the module, use the standard live
load of the equipment room as a reference.)
Suspended load of the equipment room: 1.2
kN/m2
Standard live load of the UPS room: 8–10
kN/m2
Standard live load of the battery room: 16
□ Compliant □
Incompliant

IDS2000 Intelligent Micro-Modular Data Center
Installation Guide (2000 mm High Cabinet in Dual-Row
Aisle Containment)
2 Installation Preparations
Issue Draft A (2015-06-29)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
10
Check Item
Requirement
Check Result
kN/m2
Standard live load of the monitoring center: 6
kN/m2
Equipment room net
height
For detailed requirements, see 2.4 Site
Requirements
□ Compliant □
Incompliant
Device passage and
door height and
width
Height > 2.2 m and width > 1.2 m
□ Compliant □
Incompliant
Floor levelness
Allowed deviation: 3/2000 mm
□ Compliant □
Incompliant
Elevator
Bearing capacity: > 2 t
Inner dimensions: height > 2.4 m or depth >
2.7 m
□ Compliant □
Incompliant
Cable tray
Preinstalled in the equipment room for signal
cables and power cables
□ Compliant □
Incompliant
Power supply
380–415 V AC, 3-phase, 50/60 Hz
□ Compliant □
Incompliant
Lighting
Equipment room: 500 lx
Monitoring center: 500 lx
Test area: 500 lx
□ Compliant □
Incompliant
Water source
For the detailed requirements, see 4.4.1
Requirements of Air Conditioner Pipe
Connectors and Water Quality
□ Compliant □
Incompliant
Fire extinguishing
Indoor gaseous fire extinguisher
□ Compliant □
Incompliant
Floor drain
DN50 or larger, made of cast iron or stainless
steel
□ Compliant □
Incompliant
Module grounding
The grounding system of a data center must be a
TN-S or TN-C-S system
Ground bars on cable trays
Ground bars under the raised floor
□ Compliant □
Incompliant
Cooling port
Condensate port: For the detailed condensate
drainage requirements for air conditioners, see
4.4.1 Requirements of Air Conditioner Pipe
Connectors and Water Quality
□ Compliant □
Incompliant
Humidifier water pipe port: Connects to external
water pipes to supply water to the humidifier.
For the detailed requirements, see 4.4.1
Requirements of Air Conditioner Pipe
Connectors and Water Quality
□ Compliant □
Incompliant
Monitoring port
One switch Ethernet port: Connects to the
□ Compliant □

IDS2000 Intelligent Micro-Modular Data Center
Installation Guide (2000 mm High Cabinet in Dual-Row
Aisle Containment)
2 Installation Preparations
Issue Draft A (2015-06-29)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
11
Check Item
Requirement
Check Result
customer subnet to monitor devices inside the
module
Incompliant
One skylight controller dry contact: Connects to
the fire extinguishing system to link the fire
extinguishing system and the skylights
□ Compliant □
Incompliant
If any of the requirements is not met, contact Huawei technical support.
2.4 Site Requirements
Equipment Room Height Requirement
Figure 2-2 shows the heights of modules with 2000 mm high cabinets in dual-row aisle
containment.
If 2000 mm high cabinets are deployed, the maximum module height includes the size of
open skylights. Therefore, the net height requirement for an equipment room is the same
regardless of whether a cable tray is deployed, as shown in Table 2-2.
Table 2-2 Equipment room net height requirement
Scenario
Net Height (Without
Base)
Net Height (with Base)
2000 mm scenario
> 2600 mm
> 2850 mm

IDS2000 Intelligent Micro-Modular Data Center
Installation Guide (2000 mm High Cabinet in Dual-Row
Aisle Containment)
2 Installation Preparations
Issue Draft A (2015-06-29)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
12
Figure 2-2 Height of a module in 2000 mm scenario (unit: mm)
(1) The maximum height of a module
without a base: 2550 mm
(2) The maximum height of a module with
a base: 2800 mm
Module Layout Requirement
Figure 2-3 shows the equipment room space requirements for a modular data center.
The cabinet layout shown in the figure is for ease of description and does not provide reference for
engineering layout.