Huawei 1288H V5 User manual

123
1288H V5 Server Quick Start Guide
Document Issue: 07 (2018-10-30) BOM: 31508821 (2/3)
Huawei Technologies Co., Ltd.
Copyright © Huawei Technologies Co., Ltd. 2018 All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei
Technologies Co., Ltd.
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective holders.
The information in this document is subject to change without notice. Every effort has been made in the preparation of this
document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not
constitute a warranty of any kind, express or implied.
1. Specifications
The Huawei FusionServer 1288H V5 server (1288H V5) is designed for high-performance
computing, database, web server, virtualization, basic enterprise, and telecom service
applications.
Technical Specifications
For details, see the 1288H V5 Server V100R005 User Guide.
Dimensions
(H x W x D)
Chassis with 3.5-inch hard drives:
43 mm x 436 mm x 748 mm (1.69 in. x 17.17 in. x 29.45 in.)
Chassis with 2.5-inch hard drives:
43 mm x 436 mm x 708 mm (1.69 in. x 17.17 in. x 27.87 in.)
Temperature
Operating range: 5°C to 45°C (41°F to 113°F)
(ASHRAE Classes A3 and A4 compliant)
Storage range: –40°C to +65°C (–40ºF to + 149ºF)
Maximum change rate: 20°C/h (36°F/h)
Relative humidity
(RH, non-condensing)
Operating range: 8% to 90%
Storage range: 5% to 95%
Maximum change rate: 20%/h
Maximum altitude
≤3050 m (10006.44 ft). According to the ASHRAE standards of
2015, for altitudes above 950 m (3116.79 ft), the highest
operating temperature decreases by 1°C (1.8°F) for every
increase of:
o300 m (984.24 ft) in altitude when the server configuration
complies with ClassA2 standards.
o175 m (575.14 ft) in altitude when the server configuration
complies with Class A3 standards.
o125 m (410.10 ft) in altitude when the server configuration
complies with Class A4 standards.
HDDs cannot be used at an altitude of over 3000 m (9842.5 ft).
2. Front and Rear Panels
1
Built-in DVD drive (optional)
2
Label plate with an SN label
3
Fault diagnosis LED
4
Health indicator
5
Network port connection status indicator
6
NMI button
7
Power button/indicator
8
UID button/indicator
9
USB 2.0 port
10
USB 3.0 port
11
VGA port
12
Hard drive fault indicator
13
Hard drive activity indicator
14
Hard drive
1
PCIe slot 1
2
Data transmission status indicator
3
Connection status indicator
4
Data transmission status indicator
5
Connection status indicator
6
PCIe slot 2
7
PCIe slot 3
8
Power supply module (PSU) 1
9
PSU indicator
10
PSU latch
11
PSU 2
12
PSU sockets
13
Flexible NIC (optional)
14
USB 3.0 ports
15
UID indicator
16
Serial port
17
Management network port
18
GE electrical ports
19
VGA port
20
10GE electrical port
21
Connection status indicator/Data
transmission status indicator
22
Transmission rate indicator
23
10GE optical port
24
Transmission rate indicator
25
Connection status indicator/Data
transmission status indicator
-
-
3. Indicators and Buttons
Indicators and buttons on the front panel
No.
Indicator
State Description
Remarks
3
Fault diagnosis
LED
---: The server is operating normally.
Error code: A server component is faulty.
For details about
error codes and
alarm handling,
see the Huawei
Rack Server iBMC
Alarm Handling.
4
Health indicator
Steady green: The server is operating
properly.
Blinking red at 1 Hz: A major alarm has
been generated on the server.
Blinking red at 5 Hz: A critical alarm has
been generated on the server.
5
Network port
link indicator
There are two 10GE and two GE ports.
Steady green: The network port is properly
connected.
Off: The network port is not in use or has
failed.
When a network
port is faulty,
contact Huawei
technical support
to replace the
mainboard.
6
NMI button
A non-maskable interrupt (NMI) is generally
triggered to stop the OS for debugging. To
trigger an NMI, you can press this button or
None
No.
Indicator
State Description
Remarks
click the button on the iBMC WebUI.
NOTICE
Do not press this button when the server is
operating properly. An NMI does not
gracefully shut down the OS and causes
service interruption and data loss.
Before pressing this button, ensure that the
OS has the NMI processing program.
Otherwise, the OS may crash.
7
Power
button/indicator
Power indicator
Off: The server is not connected to a power
source.
Blinking yellow: The iBMC is starting.
Steady yellow: The server is ready to power
on.
Steady green: The server is properly
powered on.
Power button
When the server is powered on, you can
press this button to shut down the OS.
When the server is powered on, holding
down this button for 6 seconds will forcibly
power off the server.
When the server is ready to be powered on,
you can press this button to start the server.
None
8
UID
button/indicator
UID indicator
Steady or blinking blue: The server is being
located.
Off: The server is not being located.
UID button
You can press this button to turn on or off
the UID indicator.
Pressing and holding down this button for 4
to 6 seconds will reset the iBMC.
None
Indicators and buttons on the rear panel
No.
Indicator
State Description
Remarks
9
PSU indicator
Steady green: The power input
and output are normal.
Blinking green at 1 Hz:
–The input is normal, the
server is standby, and the
PSU is in MV6 mode. (The
output voltage is 6.7 V.)
–The input is overvoltage or
undervoltage.
–The PSU is in deep
hibernation mode.
Blinking green at 4 Hz: An
online firmware upgrade is
being performed.
Steady orange: The input is
normal, but no power output is
supplied due to overheat
protection, overcurrent
protection, short circuit
protection, output overvoltage
protection, or some component
failures.
Replace the
PSU if the
indicator is in
any of the
following
states:
Blinking
green at 1
Hz after
the server
is
normally
powered
on.
Steady
orange

456
No.
Indicator
State Description
Remarks
Off: No AC power is supplied.
15
UID indicator
Steady or blinking blue: The
server is being located.
Off: The server is not being
located.
None
17/18
Managem
ent
network
port/GE
electrical
port
Connection
status
indicator
Steady green: The network port
is properly connected.
Off: The network port is not
connected.
None
Data
transmission
status
indicator
Blinking yellow: Data is being
transmitted.
Off: No data is being
transmitted.
None
20
10GE
electrical
port
Transmission
rate indicator
Steady green: The data
transmission rate is 10 Gbit/s.
Steady yellow: The data
transmission rate is 1 Gbit/s.
Off: The network port is not
connected.
None
Connection
status
indicator/Data
transmission
status
indicator
Steady green: The network port
is properly connected.
Blinking green: Data is being
transmitted.
Off: The network port is not
connected.
None
23
10GE
optical
port
Connection
status
indicator/Data
transmission
status
indicator
Steady green: The network port
is properly connected.
Blinking green: Data is being
transmitted.
Off: The network port is not
connected.
None
Transmission
rate indicator
Steady green: The data
transmission rate is 10 Gbit/s.
Steady yellow: The data
transmission rate is lower than
10 Gbit/s.
Off: The network port is not
connected.
None
4. Installation
CAUTION
Before unpacking and installing the server, wear an ESD wrist strap or gloves to avoid
damage to electrostatic-sensitive parts.
At least two people are required to move the server to the cabinet.
1. Install the server into the cabinet.
1) Place the server on the guide rails and push it into the cabinet.
2) Align the server mounting ears with the cabinet mounting bars, and tighten the captive
screws on the mounting ears.
2. Connect cables to service and management network ports as required.
3. Connect the power cables.
Circuit breakers rated 32 A AC or 63 A DC are recommended.
5. Power-on
If…
Then…
The PUSs are not yet powered on
Power on the PSUs.
The server is on standby after the PSUs
are powered on
Press the power button on the front panel.
You want to power on the server
remotely
Run the ipmcset -d powerstate -v 1 command on
the iBMC CLI.
Click the power control button on the iBMC
WebUI.
For details, see the Huawei Rack Server iBMC User Guide.
6. Error Code Reference
Error Code
Fault Description
Remarks
---
The server is operating normally.
-
A00
Air intake vent exceeds the operating
temperature limit.
-
A0X
CPU Xexceeds the operating temperature limit.
X: CPU number
b01
Power supply to the mainboard is abnormal or
faulty.
-
b02
The RAID controller card is abnormal or faulty.
-
C0X
CPU Xis abnormal or faulty.
X: CPU number
E01
CMOS battery is abnormal or faulty.
-
F0X
Fan module Xis abnormal or faulty.
X: fan module number
HXX
Hard drive in slot XX is abnormal or faulty.
XX: hard drive slot number
L01
A cable connection is abnormal or faulty.
-
P0X
PSU Xis abnormal or faulty.
X: PSU number
XXX
DIMM XXX is abnormal or faulty.
XXX: DIMM number
Error Code
Fault Description
Remarks
In this table, Xis an integer.
7. Follow-up
After the server is successfully powered on, configure the server. For details, see the 1288H V5
Server V100R005 User Guide.
To obtain the document:
Scan the QR code.
Visit Huawei technical support website.
8. Hazardous Substance Statement for
Electronic and Electrical Products
9. FCC
Supplier’s Declaration of Conformity (SDoC)
Unique Identifier:
trade name: Huawei; product name: Server;
model number: H12H-05,FusionServer 1288H
V5,1288H V5
Responsible Party- U.S. Contact Information
Huawei Technologies USA Inc.
5700 Tennyson Parkway, Suite 500
Plano, Texas 75024
Main: 214-919-6000 / TAC Hotline: [phone]
FCC Compliance Statement ( for products subject to Part 15)
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Component
Hazardous Substance
Cd
Pb
Hg
Cr (VI)
PBBs
PBDEs
Chassis
◯
－
◯
◯
◯
◯
PCBA
◯
－
◯
◯
◯
◯
Cables
◯
－
◯
◯
◯
◯
Corollary equipment
◯
－
◯
◯
◯
◯
Accessories
◯
－
◯
◯
◯
◯
This table is prepared in accordance with the provisions of SJ/T 11364.
◯: indicates that the content of the hazardous substance contained in all of the homogenous
materials for the component is below the limit specified in GB/T 26572.
-: indicates that the content of the hazardous substance contained in at least one of the
homogenous materials for the component is above the limit specified in GB/T 26572.