Huawei UPS2000-A-6 kVA User manual

UPS2000-A-(6 kVA-10 kVA)
User Manual
Issue
04
Date
2019-05-05
HUAWEI TECHNOLOGIES CO., LTD.

Issue 04 (2019-05-05)
Copyright © Huawei Technologies Co., Ltd.
i
Copyright © Huawei Technologies Co., Ltd. 2019. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior
written consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and
the customer. All or part of the products, services and features described in this document may not be
within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,
information, and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Huawei Technologies Co., Ltd.
Address:
Website:
Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
http://e.huawei.com

UPS2000-A-(6 kVA-10 kVA)
User Manual
About This Document
Issue 04 (2019-05-05)
Copyright © Huawei Technologies Co., Ltd.
ii
About This Document
Purpose
This document describes the UPS2000-A-(6 kVA-10 kVA) in terms of features, performance,
appearance, structure, working principle, installation, operation, and maintenance. UPS is
short for uninterruptible power system.
Intended Audience
This document is intended for:
Sales Engineer
Technical Support Engineer
System Engineer
Hardware Installation Engineer
Commissioning Engineer
Data Configuration Engineer
Maintenance Engineer
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Symbol
Description
Indicates an imminently hazardous situation which, if
not avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
Indicates a potentially hazardous situation which, if not
avoided, could result in equipment damage, data loss,
performance deterioration, or unanticipated results.

UPS2000-A-(6 kVA-10 kVA)
User Manual
About This Document
Issue 04 (2019-05-05)
Copyright © Huawei Technologies Co., Ltd.
iii
Symbol
Description
NOTICE is used to address practices not related to
personal injury.
Calls attention to important information, best practices
and tips.
NOTE is used to address information not related to
personal injury, equipment damage, and environment
deterioration.
Change History
Changes between document issues are cumulative. The latest document issue contains all the
changes made in earlier issues.
Issue 04 (2019-05-05)
Updated the section "Operating Environment".
Issue 03 (2018-01-16)
Added the description of device application scenarios.
Issue 02 (2017-11-27)
Updated the section "Operating Environment".
Issue 01 (2015-08-18)
This is the first release.

UPS2000-A-(6 kVA-10 kVA)
User Manual
Contents
Issue 04 (2019-05-05)
Copyright © Huawei Technologies Co., Ltd.
iv
Contents
About This Document.................................................................................................................... ii
1 Safety Precautions.........................................................................................................................1
1.1 General Safety ..............................................................................................................................................................1
1.2 Electrical Safety............................................................................................................................................................3
1.3 Operating Environment ................................................................................................................................................5
1.4 Battery Safety ...............................................................................................................................................................6
1.5 Mechanical Safety ........................................................................................................................................................8
1.6 Laying Out Cables........................................................................................................................................................9
2 Overview.......................................................................................................................................10
2.1 Model Number Description........................................................................................................................................10
2.2 Working Principle....................................................................................................................................................... 11
2.2.1 Conceptual Diagram................................................................................................................................................ 11
2.2.2 Working Modes........................................................................................................................................................12
2.3 Appearance .................................................................................................................................................................12
2.4 Optional Components.................................................................................................................................................17
3 Installation....................................................................................................................................22
3.1 Preparations................................................................................................................................................................22
3.1.1 Site...........................................................................................................................................................................22
3.1.2 Tools ........................................................................................................................................................................24
3.1.3 Power Cables...........................................................................................................................................................25
3.1.4 Unpacking and Checking.........................................................................................................................................28
3.2 Single UPS Installation...............................................................................................................................................29
3.2.1 Routing Cables ........................................................................................................................................................29
3.2.2 Securing a UPS........................................................................................................................................................30
3.2.3 Connecting Cables...................................................................................................................................................34
3.2.3.1 Connecting Cables to the UPS Standard Version with Standard Backup Time ....................................................34
3.2.3.2 Connecting Cables to the UPS Professional Version with Standard Backup Time...............................................35
3.2.3.3 Connecting Cables to the UPS Standard Version with Long Backup Time..........................................................36
3.2.3.4 Connecting Cables to the UPS Professional Version with Long Backup Time ....................................................37
3.3 Parallel System Installation ........................................................................................................................................39
3.3.1 Routing Cables ........................................................................................................................................................39
3.3.2 Securing UPSs in a Parallel System.........................................................................................................................40

UPS2000-A-(6 kVA-10 kVA)
User Manual
Contents
Issue 04 (2019-05-05)
Copyright © Huawei Technologies Co., Ltd.
v
3.3.3 Connecting Cables to Parallel UPSs (Professional Version with Standard Backup Time) ......................................40
3.3.4 Connecting Cables to Parallel UPSs (Professional Version with Long Backup Time)............................................42
3.4 Installing a Backfeed Protection Device.....................................................................................................................44
3.4.1 Backfeed Protection Device Specifications.............................................................................................................44
3.4.2 Feedback Prevention Connections (With Dry Contract Control).............................................................................45
3.5 Check After Installation..............................................................................................................................................47
4 Control Panel ...............................................................................................................................49
4.1 Introduction ................................................................................................................................................................49
4.2 Indicators....................................................................................................................................................................49
4.3 Functional Buttons......................................................................................................................................................50
4.4 LCD............................................................................................................................................................................51
4.5 LCD Startup Screens ..................................................................................................................................................51
4.5.1 Starting the UPS in Normal Mode...........................................................................................................................56
4.5.2 Starting the UPS in Battery Mode ...........................................................................................................................56
4.6 LCD Menu Hierarchy.................................................................................................................................................57
4.6.1 Control Menu...........................................................................................................................................................60
4.6.2 Setting Menu............................................................................................................................................................62
4.6.3 Active Alarm Display Menu ....................................................................................................................................73
4.6.4 Historical Alarms Display Menu .............................................................................................................................74
5 Operations ....................................................................................................................................76
5.1 Checking Before Powering On the UPS.....................................................................................................................76
5.2 Single UPS Operations ...............................................................................................................................................76
5.2.1 Starting the UPS ......................................................................................................................................................76
5.2.2 Shutting down the UPS............................................................................................................................................83
5.2.3 Performing EPO.......................................................................................................................................................84
5.3 Parallel System Operations.........................................................................................................................................85
5.3.1 Starting the Parallel System.....................................................................................................................................85
5.3.2 Shutting Down the Parallel System .........................................................................................................................93
5.3.3 Performing EPO for a Parallel System ....................................................................................................................95
5.3.4 Removing a UPS from a Parallel System................................................................................................................96
5.3.5 Adding a UPS from a Parallel System.....................................................................................................................99
5.3.6 Replacing a UPS from a Parallel System...............................................................................................................101
6 Communications .......................................................................................................................105
6.1 Optional Communications Components...................................................................................................................105
6.2 SNMP Card...............................................................................................................................................................105
6.3 Modbus Card ............................................................................................................................................................106
6.4 Dry Contact Card......................................................................................................................................................106
7 Routine Maintenance ...............................................................................................................107
7.1 UPS Maintenance .....................................................................................................................................................107
7.1.1 Monthly Maintenance............................................................................................................................................107

UPS2000-A-(6 kVA-10 kVA)
User Manual
Contents
Issue 04 (2019-05-05)
Copyright © Huawei Technologies Co., Ltd.
vi
7.1.2 Quarterly Maintenance ..........................................................................................................................................108
7.1.3 Yearly Maintenance ...............................................................................................................................................108
7.2 Battery Maintenance.................................................................................................................................................109
7.2.1 Precautions............................................................................................................................................................. 110
7.2.2 Monthly Maintenance............................................................................................................................................ 110
7.2.3 Quarterly Maintenance .......................................................................................................................................... 111
7.2.4 Yearly Maintenance ............................................................................................................................................... 111
8 Troubleshooting........................................................................................................................113
9 Technical Specifications ..........................................................................................................115
9.1 Physical Specifications............................................................................................................................................. 115
9.2 Environmental Specifications................................................................................................................................... 116
9.3 Mains Input Electrical Specifications....................................................................................................................... 116
9.4 Bypass Input Electrical Specifications...................................................................................................................... 117
9.5 Output Electrical Specifications ............................................................................................................................... 118
9.6 Battery Electrical Specifications............................................................................................................................... 119
9.7 ECO Feature.............................................................................................................................................................124
9.8 Parallel Feature.........................................................................................................................................................125
9.9 Safety Regulations and EMC....................................................................................................................................125
A Parallel Parameter List ............................................................................................................127
B Alarm Handling........................................................................................................................128
C Acronyms and Abbreviations................................................................................................145

UPS2000-A-(6 kVA-10 kVA)
User Manual
1 Safety Precautions
Issue 04 (2019-05-05)
Copyright © Huawei Technologies Co., Ltd.
1
1 Safety Precautions
1.1 General Safety
This section describes safety precautions to consider before installing, maintaining, and
operating the UPS.
To minimize the risk of personal injury and damage to equipment, read and follow all the
precautions in this document before performing any operation. The "DANGER",
"WARNING", "CAUTION", and "NOTICE" statements in this document are only
supplemental and do not represent all the safety instructions.
Only trained and qualified personnel are allowed to install, operate, and maintain Huawei
equipment.
Follow the precautions and special safety instructions provided by Huawei when operating
Huawei products. Huawei will not be liable for any consequences that are caused due to
violations regarding general safety regulations and equipment design, production, and usage
safety standards.
Declaration
Huawei does not take responsibilities for the following situations:
Operation under severe environments that are not specified in this document.
Installation or use in environments that are not specified in related international
standards.
Unauthorized product changes and software code modification.
Operations not complying with the operation instructions and safety precautions in this
document.
Damage caused by extreme natural environments.
Damage caused by using batteries provided by Huawei for non-Huawei UPSs.
Damage caused by using batteries not provided by Huawei.

UPS2000-A-(6 kVA-10 kVA)
User Manual
1 Safety Precautions
Issue 04 (2019-05-05)
Copyright © Huawei Technologies Co., Ltd.
2
Local Laws and Regulations
Equipment operations must comply with local laws and regulations. The safety instructions in
this document are only supplemental to local safety regulations.
Personal Requirements
Only Huawei engineers or engineers certified by Huawei are allowed to perform UPS
commissioning and maintenance. Otherwise, human injury or equipment damage may occur,
and any resulting UPS faults will be beyond warranty scope.
Personnel who plan to install or maintain Huawei equipment must receive thorough training,
understand all necessary safety precautions, and master the correct operation methods.
Trained and qualified personnel, or personnel certified or authorized by Huawei are:
Allowed to install, operate, and maintain the equipment.
Allowed to remove safety facilities and inspect the equipment.
Allowed to replace or change the devices or components (including software).
Operation personnel must report faults or errors that might cause serious safety issues to
related owners.
This product should be installed and used according to the installation and technical,
specification requirements found in this manual. Otherwise, the product may be damaged,
and the resulting product exceptions or component damage will be beyond the warranty
scope.
Grounding Requirements
Devices to be grounded (excluding the energy storage unit) must meet the following
requirements:
When installing a device, install the ground cable first. When removing a device, remove
the ground cable at the very end.
Do not damage the ground conductor.
Do not operate devices if the ground conductor is not installed. Before operating a device,
check the electrical connection of the device to ensure that it is securely grounded.
Personal Safety
Do not operate the product, or handle cables, during thunderstorms.
To avoid electric shocks, do not connect safety extra-low voltage (SELV) circuits to
telecommunication network voltage (TNV) circuits.
Before operating a device, wear electrostatic discharge (ESD) clothes, ESD gloves, and
an ESD wrist strap. Remove any conductors (such as jewelry or watches) before the
operation to avoid electric shocks or burns.
In the case of fire, leave the building or the equipment room immediately, and turn on the
fire alarm bell or make an emergency call. Never enter the building on fire in any case.
If the cabinet provides an ESD jack, wear an ESD wrist strap and insert the ground
terminal of the ESD wrist strap into the jack.

UPS2000-A-(6 kVA-10 kVA)
User Manual
1 Safety Precautions
Issue 04 (2019-05-05)
Copyright © Huawei Technologies Co., Ltd.
3
Ensure all switches are turned to OFF during device installation.
Power on the UPS only after authorized engineers arrive at the site.
If a C2 UPS is used in residential areas, additional measures must be taken to prevent
radio frequency interferences.
If the UPS is used for life-supporting medical apparatus and facilities such as lifts where
adequate care has to be taken to ensure personal safety, discuss with the manufacturer in
advance about the applicability, settings, management, and maintenance of the UPS,
which require special considerations during design.
Device Safety
Before operation, ensure that the device is firmly anchored to the floor or other solid
objects, such as a wall or an installation rack.
Ensure ventilation vents are unblocked while the system is operating.
Before powering on the device, ensure that all the screws inside it are securely tightened
and will not fall off during operation.
After the installation, remove packing materials from the equipment area.
Replace danger signs that have worn out or are unreadable.
A UPS can be used to serve resistive-capacitive loads, resistive loads, and
micro-inductive loads. It is recommended that a UPS not be used for pure capacitive
loads, pure inductive loads, and half-wave rectification loads. It does not apply to energy
feedback loads.
Do not alter the UPS internal structure or installation procedure unless consent from the
manufacturer is given.
Never use water to clean electrical components inside or outside the UPS.
Do not drill holes into a cabinet.
1.2 Electrical Safety
High Voltage
The high voltage power supply provides power for the device operation. Direct or indirect
contact with high voltage power sources may result in fatal injury.
Non-standard or incorrect high voltage operations may result in fire and electric shocks.
The personnel who install the AC facility must be qualified to perform high voltage and
AC operations.
When selecting, connecting, and routing power cables, ensure compliance with local
laws and regulations.
When operating the AC power supply facility, ensure compliance with local laws and
regulations.
Before connecting cables to the UPS, ensure that the input power and mains power
distribution switches and output power distribution switch are turned off.
Use only dedicated tools during high voltage and AC operations.

UPS2000-A-(6 kVA-10 kVA)
User Manual
1 Safety Precautions
Issue 04 (2019-05-05)
Copyright © Huawei Technologies Co., Ltd.
4
If the operation is performed in a damp environment, ensure that the device is dry. When
water is found in the rack or the rack is damp, switch off the power supply immediately.
High Leakage Current
Ground a device before powering it on. Otherwise, personal injury or device damage may
occur.
If a "high leakage current" tag is attached to the panel of the device, ground the protective
ground terminal on the device enclosure before connecting the AC power supply to
prevent electric shocks.
The UPS can generate high leakage currents. Using a circuit breaker that has the leakage
current protection function is not recommended.
Power Cable
Do not install or remove power cables when the device is on. Transient contact between the
core of the power cable and the conductor may generate electric arcs or sparks, which may
cause fire or damage eyesight.
Before moving or reconnecting the UPS, disconnect the mains and batteries, open the
output power distribution switch, and wait a period of at least 5 minutes after the UPS
completely powers off. Otherwise, electric shocks may occur.
Before installing or removing the power cable, open the power switch.
Before connecting a power cable, check that its label is correct.
Fuse
If a fuse needs replacing, ensure the new fuse is of the same type and specifications so that the
system runs safely.
Electrostatic Discharge
Static electricity generated by human bodies may damage the electrostatic-sensitive
components on boards, for example, the large-scale integrated (LSI) circuits.
Wear a pair of ESD gloves or a well-grounded ESD wrist strap when touching the device
or handling boards or application-specific integrated circuits (ASICs).

UPS2000-A-(6 kVA-10 kVA)
User Manual
1 Safety Precautions
Issue 04 (2019-05-05)
Copyright © Huawei Technologies Co., Ltd.
5
When holding a board, hold its edge without touching any components, especially chips.
Package boards with ESD packaging materials before storing or transporting them.
Figure 1-1 shows how to wear an ESD wrist strap.
Figure 1-1 Wearing an ESD wrist strap
Liquid Prevention
Do not place the product under areas prone to water leakage, such as near air conditioner
vents, ventilation vents, or feeder windows of the equipment room. Ensure that there is
no condensation inside the product or equipment room. Ensure that no liquid enters the
product. Otherwise, short circuits will occur and may result in serious injury or death.
If any liquid is detected inside the product, immediately disconnect the power supply and
contact the administrator.
1.3 Operating Environment
The UPS is used for commercial and industrial purposes only. It cannot be used as a power
supply for life support devices.
The TIER4 or TIER3 power supply architecture specified in TIA942, that is, dual power
supply routes, must be used in the power supply systems that are crucial to major economic
interests or order of public places, such as the national computing center, military command
system, emergency command center, railway signal system and control center, civil aviation
air traffic control center, airport command center, financial clearing center, and transaction
center.
Ensure that the product is used in an environment that meets the product design specifications
(including power grid, temperature, and humidity) to avoid causing malfunctions, damaging
components, or voiding the warranty.
The UPS operating environment must meet the requirements for the climate indicator,
mechanically active substance indicator, and chemically active substance indicator in ETSI
EN 300 019-1 class 3.6.

UPS2000-A-(6 kVA-10 kVA)
User Manual
1 Safety Precautions
Issue 04 (2019-05-05)
Copyright © Huawei Technologies Co., Ltd.
6
After unpacking the UPS, you are advised to power on the UPS as soon as possible. If you
temporarily do not use the UPS, take appropriate measures to prevent moisture, dust, and
foreign matter from entering the UPS.
After unpacking batteries, you are advised to connect the battery supply as soon as
possible. If you temporarily do not use the batteries, store them in dry and clean
environments. If batteries are stored for more than 90 days, charge them in time.
Otherwise, the battery lifespan may be affected.
Do not place the device in an environment that has inflammable and explosive air or gas. Do
not perform any operation in this kind of environment.
If the valid mains voltage exceeds 320 VAC, the UPS may be damaged.
Any operation on any electrical device in an environment that has inflammable air can cause
extreme danger. Strictly obey the operating environmental requirements specified in related
use manuals when using or storing the device.
Do not place the UPS in the following environments:
The environment that is close to flammable or explosive materials, dust, corrosive gases
or dust, conductive or magnetic dust, abnormal vibration, or collision.
Rooms or outdoor environments where temperature and humidity are not controlled
(with high temperature, low temperature, moisture, direct sunlight, or heat sources).
Non-confined environment near the ocean (0–3.7 km) and indoor or semi-indoor
environment where the temperature and humidity are not controllable, such as a simple
equipment room near the ocean, citizen house, garage, corridor, direct ventilation cabinet,
house with only the roof, railway station platform, gymnasium, aquarium, and so on.
The environment that is conducive for the growth of microorganisms such as fungus or
mildew.
The environment where rodents (such as mice) and insects exist.
1.4 Battery Safety
This section describes precautions for operating batteries.
Before operating batteries, carefully read the safety precautions to ensure correct battery
handling and connection is performed, and personal safety is managed.

UPS2000-A-(6 kVA-10 kVA)
User Manual
1 Safety Precautions
Issue 04 (2019-05-05)
Copyright © Huawei Technologies Co., Ltd.
7
To ensure battery safety and efficient battery management, use the batteries delivered with
the UPS. Huawei shall not be responsible for battery damage caused by using non-Huawei
batteries for Huawei UPSs.
Ensure lead-acid battery handling is in accordance with local regulations.
Incorrect handling of batteries may cause hazards. When operating batteries, avoid
battery short circuits and electrolyte overflow or leakage.
Electrolyte overflow may damage the device by corroding metal parts and circuit boards,
and ultimately damaging the circuit boards.
Short circuits caused by incorrect operations may cause serious injuries due to high
power of batteries.
Do not reversely connect positive and negative battery terminals.
Use batteries of the specified type. Otherwise, the batteries may be damaged.
Check battery connections periodically to ensure that all screws are securely tightened.
Install or store batteries in clean, cool, and dry environments.
Do not decompose, transform, or damage batteries. Otherwise, battery short circuit,
electrolyte leakage, and even personal injury may occur.
Preventative Measures
When installing and maintaining batteries, pay attention to the following points:
Use dedicated insulated tools.
Take measures to protect eyes, such as using eye protection devices.
Avoid skin contact with electrolyte overflow. Wear rubber gloves and protective
clothing.
When handling a battery, ensure that its electrodes always point upward. Do not tilt or
overturn batteries.
Switch off the power supply during installation and maintenance.
Battery Short Circuit
Battery short circuits may cause personal injury. The high transient current generated by a
short circuit may release a surge of power and cause a fire.
To avoid battery short circuits, do not maintain batteries while they are in use.
Harmful Gas

UPS2000-A-(6 kVA-10 kVA)
User Manual
1 Safety Precautions
Issue 04 (2019-05-05)
Copyright © Huawei Technologies Co., Ltd.
8
Do not use unsealed lead-acid batteries. Lead-acid batteries emit flammable gas. Therefore,
place and secure lead-acid batteries horizontally to prevent fire or corrosion.
Store lead-acid batteries in a place with good ventilation, and take fire safety precautions.
Battery Temperature
High temperature may result in battery distortion, damage, and electrolyte overflow.
Install or store batteries far away from fire sources and heating devices such as
transformers. Never burn batteries.
If the battery temperature exceeds 60°C, check the battery for electrolyte overflow. If
electrolyte overflows, handle the leakage immediately.
Electrolyte Leakage
In the case of electrolyte leakage, counteract and absorb the leaking electrolyte immediately.
When moving or handling a battery whose electrolyte leaks, note that the leaking electrolyte
may harm human bodies. If the electrolyte leaks, use the following substances to counteract
and absorb the leaking electrolyte:
Sodium bicarbonate (baking soda): NaHCO3
Sodium carbonate (soda): Na2CO3
When using substances to counteract and absorb electrolytes, strictly follow the guidelines
provided by the battery manufacturer.
If any personnel are exposed to battery electrolyte, wash the exposed area with clean water
immediately and seek medical advice if the situation is serious.
1.5 Mechanical Safety
Moving Sharp Objects
Wear protective gloves when moving sharp objects.

UPS2000-A-(6 kVA-10 kVA)
User Manual
1 Safety Precautions
Issue 04 (2019-05-05)
Copyright © Huawei Technologies Co., Ltd.
9
Moving Heavy Objects
Perform operations in accordance with all instructional symbols on the device.
Take caution to avoid injury when moving heavy objects.
When moving or lifting a device, hold the handle or bottom of the device.
Move the cabinet with caution. Any bumping or falling may damage the device.
Handling Fans
Do not insert fingers or boards into the operating fans until the fans are switched off, and have
stopped running.
1.6 Laying Out Cables
Binding Signal Cables
Signal cables must be bound separately from strong-current cables and high-voltage cables.
Laying Out Cables
When the temperature is low, a violent strike or vibrations may damage the cable sheathing.
To ensure cable safety, comply with the following requirements:
Cables can be laid, or installed, only when the temperature is higher than 0°C (32°F).
Handle cables with caution, especially at lower temperatures.
Before laying out cables that have been stored in temperatures lower than 0°C (32°F),
move the cables to an environment that is at the requisite ambient temperature. Store
them in this environment for at least 24 hours.
Do not drop the cables directly from the vehicle.
As the insulation layer of a cable may age, or be damaged from high temperatures,
ensure a sufficient distance between cables and the DC busbars, shunts, and fuses.
Cables prepared by the customer should be flame resistant. Cables must not be routed
behind the air exhaust vent of the cabinet. The air exhaust vent should not be blocked by
any object.
Before connecting a cable, ensure that the cable and cable label to be used meet the actual
installation requirements.

UPS2000-A-(6 kVA-10 kVA)
User Manual
2 Overview
Issue 04 (2019-05-05)
Copyright © Huawei Technologies Co., Ltd.
10
2 Overview
2.1 Model Number Description
This document involves the following UPS models.
Model
Represented By
Remarks
UPS2000-A-6KTTS-S
6 kVA standard
version with
standard backup
time
The 6 kVA model is used as a collective
name when the common features or
parameters of the four models need to be
described.
UPS2000-A-6KTTL-S
6 kVA standard
version with long
backup time
UPS2000-A-6KTTS-P
6 kVA
professional
version with
standard backup
time
UPS2000-A-6KTTL-P
6 kVA
professional
version with long
backup time
UPS2000-A-10KTTS-S
10 kVA standard
version with
standard backup
time
The 10 kVA model is used as a collective
name when the common features or
parameters of the four models need to be
described.
UPS2000-A-10KTTL-S
10 kVA standard
version with long
backup time
UPS2000-A-10KTTS-P
10 kVA
professional
version with
standard backup
time

UPS2000-A-(6 kVA-10 kVA)
User Manual
2 Overview
Issue 04 (2019-05-05)
Copyright © Huawei Technologies Co., Ltd.
11
Model
Represented By
Remarks
UPS2000-A-10KTTL-P
10 kVA
professional
version with long
backup time
Figure 2-1 shows a UPS model number.
Figure 2-1 UPS model number
Table 2-1 describes the UPS model number.
Table 2-1 UPS model number details
No.
Meaning
Description
1
Product category
UPS, short for uninterruptible power system
2
Product series
2000
3
UPS subcategory
A series
4
Output capacity
Unit: VA
6K: 6 kVA
10K: 10 kVA
5
UPS type
TT: tower-mounted UPS
6
Standard/Long backup
time model
S: standard backup time model, using built-in
batteries that provide standard backup time.
L: long backup time model, using external
large-capacity batteries that provide long backup
time.
7
Standard/Professional
standard
S: standard version
P: professional version
2.2 Working Principle
2.2.1 Conceptual Diagram
Figure 2-2 shows the UPS conceptual diagram.

UPS2000-A-(6 kVA-10 kVA)
User Manual
2 Overview
Issue 04 (2019-05-05)
Copyright © Huawei Technologies Co., Ltd.
12
Figure 2-2 UPS conceptual diagram
2.2.2 Working Modes
The UPS has the following working modes:
Normal mode
When the mains is normal, the rectifier boosts the mains input voltage and converts the
AC power into stable DC power for the inverter, and the mains charges batteries over a
charger. Then the inverter converts the DC power into stable AC power, which is
supplied to loads.
Battery mode
When the mains is abnormal or disconnected, the rectifier step-up transformer boosts the
DC power supplied from batteries. Then the inverter converts the DC power into stable
AC power for powering loads.
Bypass mode
The mains supplies power directly to loads after filtering. The UPS transfers to bypass
mode when overload, overtemperature, or faults occur. This mode does not provide
battery backup capability.
ECO mode
If the bypass voltage and frequency are in the specified range, the UPS supplies power to
loads over the bypass. If the bypass voltage and frequency are outside the range, the UPS
transfers to normal or battery mode. ECO is short for economy control operation.
By default, ECO mode described in this document refers to mains ECO mode.
2.3 Appearance
Figure 2-3 shows the side view of the 6 kVA/10 kVA UPS.

UPS2000-A-(6 kVA-10 kVA)
User Manual
2 Overview
Issue 04 (2019-05-05)
Copyright © Huawei Technologies Co., Ltd.
13
Figure 2-3 Side view
(1) Control panel
(2) Castor
(3) Mounting bracket (optional)
(4) Brake pad
Mounting brackets are optional for UPSs with standard backup time and battery boxes and are not
required for UPSs with long backup time.
Figure 2-4 shows the rear view of the 6 kVA/10 kVA UPS standard version with standard
backup time.