HUBBELL LIGHTING Architectural Area Lighting EPA-T User manual

A96473
EPA-T
7/27/2010
INSTALLATION INSTRUCTIONS CATALOG NUMBER
PART NO.APPRVDDATE
DATE REV.
16555 East Gale Avenue
City of Industry, CA 91745
[phone]
50W MAXIMUM.
NOTE:
BY OTHERS
MR16 LAMP
(3) S/S SET SCREW
THE MAIN POWER SUPPLY LEADS
AUXILIARY POWER SUPPLY AND PASS
SCREWS. REMOVE HATCH.
4. LOOSEN (2) HATCH MOUNTING
BUT DO NOT TIGHTEN YET. ORDER TO ADJUST THE HORIZONTAL
ADAPTER ON POLE TOP IN
8. ROTATE EGRESS POST TOP
(2) HATCH MOUNTING SCREWS.
POST TOP ADAPTER AND TIGHTEN
SET SCREWS TO SECURE ADAPTER.
LAMP POSITION. TIGHTEN (3) S/S
7. REPLACE HATCH ON THE EGRESS
TIGHTEN (1) THUMB SCREW.
POSITION TO THE DESIRED LOCATION.
ADJUST THE VERTICAL LAMP
6. LOOSEN (1) THUMB SCREW AND
GROUNDING WIRE
THUMB SCREW
GROUNDING
EGRESS TENON
ADAPTER WIRE WAY
1. TURN OFF ALL POWER.
SCREWS
(2) HATCH MOUNTING
HATCH 4" O.D. POLE (REF)
LAMP PROVIDED BY OTHERS.
5. INSTALL (1) MR16 (50 WATT MAX)
EGRESS TENON. (BY OTHERS)
AND SECURE THE FIXTURE TO THE
FIXTURE OVER THE EGRESS TENON
TOP FIXTURE. PLACE THE POST TOP
MAIN POWER SUPPLY TO THE POST
EGRESS POST TOP ADAPTER TO THE
2. CONNECT THE LEADS FROM THE
INSTALLATION INSTRUCTIONS:
ADAPTER ON THE POLE TOP
3. PLACE THE EGRESS POST TOP
THROUGH THE ADAPTER WIREWAY.
9. CONNECT THE LEADS FROM THE

A96474
EPA-C
INSTALLATION INSTRUCTIONS CATALOG NUMBER
PART NO.APPRVDDATE
DATE REV.
16555 East Gale Avenue
City of Industry, CA 91745
[phone]
50W MAXIMUM.
NOTE:
BY OTHERS
MR16 LAMP
(6) S/S SET SCREW
SCREWS
(2) HATCH MOUNTING
THUMB SCREW
GROUNDING
EGRESS TENON
ADAPTER WIRE WAY
1. TURN OFF ALL POWER.
ORDER TO ADJUST THE HORIZONTAL
SET SCREWS TO SECURE ADAPTER.
ADAPTER ON POLE TOP IN
8. ROTATE EGRESS POST TOP
9. CONNECT THE LEADS FROM THE
(2) HATCH MOUNTING SCREWS.
POST TOP ADAPTER AND TIGHTEN
7. REPLACE HATCH ON THE EGRESS
TIGHTEN (1) THUMB SCREW.
6. LOOSEN (1) THUMB SCREW AND
POSITION TO THE DESIRED LOCATION.
ADJUST THE VERTICAL LAMP
GROUNDING WIRE
LAMP PROVIDED BY OTHERS.
EGRESS TENON. (BY OTHERS)
AND SECURE THE FIXTURE TO THE
FIXTURE OVER THE EGRESS TENON
TOP FIXTURE. PLACE THE POST TOP
AUXILIARY POWER SUPPLY AND PASS
EGRESS POST TOP ADAPTER TO THE
SCREWS. REMOVE HATCH.
4. LOOSEN (2) HATCH MOUNTING
BUT DO NOT TIGHTEN YET.
ADAPTER ON THE POLE TOP
3. PLACE THE EGRESS POST TOP
THROUGH THE ADAPTER WIREWAY.
THE MAIN POWER SUPPLY LEADS
2. CONNECT THE LEADS FROM THE
INSTALLATION INSTRUCTIONS:
LAMP POSITION. TIGHTEN (6) S/S
HATCH 4" O.D. POLE (REF)
MAIN POWER SUPPLY TO THE POST
5. INSTALL (1) MR16 (50 WATT MAX)

A96475
EPA-C/T
7/27/2010
INSTALLATION INSTRUCTIONS CATALOG NUMBER
PART NO.APPRVDDATE
DATE REV.
16555 East Gale Avenue
City of Industry, CA 91745
[phone]
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions
should always be followed, including the following:
a) READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
b) Do not mount near gas or electrical heaters.
c) Equipment should be mounted in locations and at heights where it will
not readily be subjected to tampering by unauthorized personnel.
d) The use of accessory equipment not recommended by the manufacturer
may cause an unsafe condition.
e) CAUTION: Halogen cycle lamp(s) are used in this equipment. To avoid
shattering: Do not operate lamp in excess of rated voltage, protect lamp
against abrasion and scratchese and against liquids when lamp is operating,
f) Halogen cycle lamps operate at high temperatures. Do not store or place
flammable materials near lamp.
g) Do not use this equipment for other than intended use.
SAVE THESE INSTRUCTIONS
dispose of the lamp with care.