HUBBELL LIGHTING KIM LIGHTING KLV206 User manual

Tools Required: qPhilips Screwdriver qFlat Blade Screwdriver qAdjustable Wrench
 q 1/8” Allen Wrench q3/16” Allen Wrench
INSTRUCTIONS PERTAINING TO A RISK OF FIRE OR INJURY TO PERSONS
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: To reduce the risk of FIRE OR INJURY TO PERSONS: Do not overdrive fixtures with greater
than 12 volts or fixture over-heating and short lamp life will occur. Do not overload the transformer by
installing (or relamping) higher wattage lamps than planned. Note: Total wattage of all lamps connected to one
transformer must not exceed the capacity of that transformer. Do not install luminaire within 10 feet (3.04m) of a
pool, spa or fountain. DO NOT operate luminaire with missing or damaged lens.
SAFETY WARNING: When relamping, be sure electrical supply is OFF. Use discretion when touching
fixture and be sure to allow fixture to cool before relamping.
MAINTENANCE: To maintain light efficiency and prevent fixture-overheating, glass lenses and enclosure must
be kept clean and free of dirt, dust, leaves, trash (combustible materials) and mineral deposits from water.
Particular care should be taken not to locate fixtures where small children can reach them if higher wattages
are used.
KEEP THIS SHEET FOR FUTURE REFERENCE.
!
!
3/24/14 EC 140326006 Status A Part No. 93049435
*Consult Kim Landscape Lighting Collection Catalog for mounting device options.
Accent Light - KLVL206 Installation Instructions
Make certain the electrical supply is OFF before starting fixture installation.
!
16555 East Gale Avenue
City of Industry, CA 91745-1788
626/968-5666 • FAX [phone]
2. Tighten coupling onto
mounting device.
1. Remove coupling from fixture.
IMPORTANT: Do not overload the transformer by installing higher wattage fixtures than planned. Remember, the total wattage of all
fixtures connected to one transformer must not exceed the capacity of that transformer.
IMPORTANT: When fixtures are aimed up, particular care should be taken to keep lens free of debris and mineral deposits. When
fixtures are in an area where debris or mineral deposits are likely to be a problem, lower wattage lamps should be used, and lenses
should be cleaned on a regular maintenance schedule.
3. Install fixture onto coupling.
Attach fixture leads.
Note: KIM KLV Mounting
Options can be installed
before fixture is attached.
KLV206
4. Loosen set screw, adjust
fixture rotation, and tighten
set screw.

KIM LIGHTING LIMITED WARRANTY
When installed in accordance with Kim Installation Instructions and accepted trade practices, the following shall apply:
General Product Limited Warranty Coverage
All material and component parts used in the manufacture of Kim Products, are warranted to be free from defects of material
and/or workmanship for a period of 1 year from date of sale, with the following exceptions:
Auxiliary Equipment
All auxiliary equipment (such as lamps, ballasts, and transformers) provided by and/or included in Kim Products shall carry
the component manufacturer’s warranty.
Copper and Bronze Landscape Components
Copper and Bronze Landscape fixture components shall be warranted against defects of material and/or workmanship, and
failure due to corrosion, for a period of 25 years from date of sale.
Composite In-Grade Components
Composite In-Grade fixture components installed below grade, shall be warranted against defects of material and/or
workmanship, and failure due to corrosion, for a period of 7 years from date of sale.
Aluminum Landscape Components
Aluminum Landscape fixture components not in direct contact with soil, shall be warranted against defects of material and/
or workmanship for a period of 3 years from date of sale. Aluminum fixture components in direct contact with soil shall be
warranted from defects of material and failure from corrosion for a period of 1 year from date of sale.
Limit of Liability and General Conditions
Only products which are installed, used and maintained in accordance with applicable Kim instructions, specifications and
accepted trade practices, are covered by the Kim Warranty. During the warranty period, with proof of purchase, Kim will
repair or replace with the same or similar product, at Kim’s option, without charge. Labor costs are the owner’s responsibility
and are excluded from this warranty. This warranty is void if the product is modified, tampered with, misapplied, poorly
installed, improperly maintained, or subjected to abnormal conditions.
Repair or replacement as provided under this warranty is the exclusive remedy of the purchaser. This warranty is in lieu of all
other warranties, expressed or implied, including any implied warranty of fitness for a particular application. Kim Lighting shall
not be liable to the purchaser for indirect or consequential damages.
Kim Lighting • 16555 E. Gale Ave. • City of Industry, CA 91716-0080 • 626/968-5666 • FAX [phone] Page 2
Accent Light - KLVL206 Installation Instructions
How may we serve you better? Please let us know. Visit our website at: www.kimlighting.com. Your concerns are important to us
*Note: Swivel stem must
be installed with the
mounting threads facing
down-to-horizontal.
Fixtures may not be
installed with mounting
threads facing upward
unless shielded from rain
or sprinklers.
90°
*
*
Fixture Orientation
5. To adjust angle, loosen swivel screw,
do not disengage. Hold fixture at
desired angle and tighten swivel screw.
Fixture may be aimed up or down.
6. Connect fixture cable to main system
cable with a sealed connector.
Additional wire and connectors may be purchased from Kim Lighting:
KLV427 #12-2 Cable KLV410 Connector
KLV432 #8-2 Cable KLV411 Connector
Note: Low voltage cable is intended for shallow burial, maximum of 6” (152 mm).