HUBBELL LIGHTING KIM LIGHTING B30 Series Installation and operating instructions

Revised 06/26/12 EC 120626005 Status 14 Part No. 95268
B30 Series 8"Round Traditional Bollard
Installation & Maintenance Instructions
P.O. Box 60080 •16555 East GaleAve.
City of Industry, California 91716-0080
626/968-5666 • FAX [phone]
WARNING: Fixtures must be grounded in accordance with local codes or the National Electrical Code.
Failure to do so may result in serious personal injury.
MAINTENANCE WARNING: To maintain light efficiency and prevent fixture overheating, reflector and lens must
be kept clean and free of dirt, dust, leaves, and trash. For optimum performance a regularly scheduled
maintenance program should be followed.
CAUTION: All wiring must be done by a qualified electrician. KEEP THIS SHEET FOR FUTURE REFERENCE.
B30
8" Round
Top Cover/
Lens Assembly
Reflector
Assembly
Socket/Base
Assembly
Riser
(Pole Body)
Base/Ballast
Bracket Assembly
Base Casting / Ballast Assembly Installation:
Make certain the electrical supply is OFF before starting installation.
1. Install the base casting/ballast assembly on the pre-set anchor bolts. Use flat washers
and hex nuts both below and above the base casting.
2. Level the top edge of the casting by adjusting the bottom leveling nuts. Tighten the
upper nuts.
3. Connect the circuit ground wire to the grounding lug on the ballast bracket.
4. Connect power supply leads to the ballast input leads. See diagram below. NOTE:
For incandescent fixtures, connect the power supply leads directly to the lamp leads -
no ballast required.
ATTENTION: If your fixture is equipped with a multi-tap ballast and if no voltage was specified on the purchase order,
the ballast has been wired for operation on a 277 volt circuit (347v in Canada). If other than 277 volts is required, i.e.
120v, 208v, 240v, connect incoming voltage lead to selected voltage lead on ballast. Cap off all unused voltage leads.
Tools Required: Ratchet with N" Deep Socket F" Hex Key B" Hex Key
N" Open-end Wrench Flat Blade Screwdriver
Fixture Installation:
Make certain the electrical supply is OFF before starting
fixture installation.
1. To protect finish, lay fixture horizontally on soft cloth with open-
end of fixture next to installed base casting/ballast assembly.
2. Connect fixture ground lead (green) to the short green wire con-
nected to the grounding lug on the ballast bracket.
3. Connect the lamp leads to the ballast. NOTE: For incandescent
fixtures, connect the power supply leads directly to the lamp leads.
4. Place pole body over ballast assembly and slowly turn until body
drops into retaining slots, then twist clockwise to lock the pole onto
the base casting.
5. Tighten the two set screws at the bottom of the pole using a F”
hex key.
LEVEL
3" Max.
Grade
Base Casting/ Ballast Assembly
Fixture Installation
Conduit
(by others)Anchor Bolt (4)
Concrete
In Concrete Pad
(Leveling)
Nut and
Washer (4)
Nut and
Washer (4)
Riser/
Pole Body
Base Casting/
Ballast Assembly
In Earth
(grade slopes away)
Final Installation Detail
!
!
!

Page 2 Kim Lighting • 16555 E. Gale Ave. • P.O. Box 60080• City of Industry, CA 91716-0080• 626/968-5666 • FAX [phone]
LAMP INSTALLATION OR REPLACEMENT:
Make certain the electrical supply is OFF before
starting lamp installation or replacement.
1. Remove fixture top cover by loosening the two screws
progressively and evenly.
2 Install or replace the lamp using only the type and
wattage shown on the fixture label. For installation, lamp
can be inserted through center of reflector stack.
3. Replace the cover making sure all gaskets are clean
and in place. Tighten the screws progressively to insure
even pressure on gaskets.
B30 Series 8""Round Bollard Installation & Maintenance Instructions
KIM LIGHTING LIMITED WARRANTY
When installed in accordance with Kim Installation
Instructions and accepted trade practices, the following shall
apply:
General Product Limited Warranty Coverage
All material and component parts used in the manufacture of
Kim Products, are warranted to be free from defects of
material and/or workmanship for a period of 1 year from date
of sale, with the following exceptions:
Auxiliary Equipment
All auxiliary equipment (such as lamps, ballasts, and
transformers) provided by and/or included in Kim Products
shall carry the component manufacturer's warranty.
Copper and Bronze Landscape Components
Copper and Bronze Landscape fixture components shall be
warranted against defects of material and/or workmanship,
and failure due to corrosion, for a period of 25 years from
date of sale.
Composite In-Grade Components
Composite In-Grade fixture components installed below
grade, shall be warranted against defects of material and/or
workmanship, and failure due to corrosion, for a period of 7
years from date of sale.
Aluminum Landscape Components
Aluminum Landscape fixture components not in direct
contact with soil, shall be warranted against defects of
material and/or workmanship for a period of 3 years from date
of sale. Aluminum fixture components in direct contact with
soil shall be warranted from defects of material and failure
from corrosion for a period of 1 year from date of sale.
Limit of Liability and General Conditions
Only products which are installed, used and maintained in
accordance with applicable Kim instructions, specifications,
and accepted trade practices, are covered by the Kim
Warranty. During the warranty period, with proof of purchase,
Kim will repair or replace with the same or similar product, at
Kim's option, without charge. Labor costs are the owner's
responsibility and are excluded from this warranty. This
warranty is void if the product is modified, tampered with,
misapplied, poorly installed, improperly maintained, or
subjected to abnormal conditions.
Repair or replacement as provided under this warranty is the
exclusive remedy of the purchaser. This warranty is in lieu of
all other warranties, expressed or implied, including any
implied warranty of fitness for a particular application. Kim
Lighting shall not be liable to the purchaser for indirect or
consequential damages.
!
How may we serve you better?
Please let us know. Visit our website at:
www.kimlighting.com
Your concerns are important to us.
!
!
CLEANING REFLECTOR ASSEMBLY
AND PLASTIC LENS:
Make certain the electrical supply is OFF.
1. Remove fixture top cover by loosening the two screws
progressively and evenly.
2 Remove the lamp.
3. Loosen the three reflector mounting screws inside the
reflector assembly near the top of the lamp socket. Note
orientation of assembly before removing.
4. Rotate the reflector assembly clockwise and lift the
assembly off of the mounting screws.
5. Clean the plastic and the reflector assembly with a mild
detergent. Rinse and wipe dry. DO NOT use an
abrasive compound or attempt to clean with a dry cloth.
6. Replace the reflector assembly and tighten the three
reflector mounting screws. These screws are not
equally spaced and the reflector assembly will fit in only
one orientation.
7. Install the correct lamp as shown on the fixture label and
check all gaskets to be sure they are clean and in place.
8. Replace the cover. Tighten the screws progressively to
insure even pressure on the gaskets.
BALLAST REPLACEMENT:
Make certain the electrical supply is OFF before
starting ballast replacement.
1. Loosen two set screws at the base of the pole using a
F" hex key.
2. Rotate the pole counter clockwise approximately 1" and
lift pole/fixture assembly upward to clear ballast
assembly.
3. Replace ballast with the correct type and wattage.
Connect all wiring as shown in the wiring diagram on
the new ballast.
4. Place the pole body over the ballast assembly and
slowly turn until the pole drops into retaining slots, then
twist clockwise to lock onto the base casting.
5 Tighten the two set screws at the base of the pole.
WARNING:
The H.I.D. / Fluorescent fixture utilizes a lamp that may
contain mercury. For information on disposal of lamp go
to website: www.lamprecycle.org