Hubbell 67L Series User manual

litecontrol.com
DO NOT MODIFY OR ALTER THIS PRODUCT IN ANY WAY, OR INSTALL IN ANY FASHION WHICH IS CONTRARY TO THE INSTRUCTIONS CONTAINED HEREIN.
IF YOU HAVE ANY QUESTIONS REGARDING THIS PRODUCT OR THE INSTALLATION OF IT, PLEASE CALL LITECONTROL ENGINEERING AT 781-294-0100.
DRAWING: 510641
REV / DATE: 0 / 1/16/2019
TOOLS REQUIRED SUPPLIED BY INSTALLER
INSTALLATION INSTRUCTIONS
FIXTURE SERIES: 67L MOUNTING TYPE: AIRCRAFT CABLES PAGE: 1 OF 3
GENERAL NOTES: (READ SHEETS COMPLETELY BEFORE STARTING)
1. LEAVE PROTECTIVE WRAPPING ON FIXTURE(S) UNTIL START OF
INSTALLATION.
2. FIXTURES ARE SUPPLIED WITH FACTORY-INSTALLED BRANCH CIRCUIT
WIRING. REFER TO SUPPLEMENTAL INSTRUCTION SHEET WEHN MAKING
CONNECTIONS.
3. APPROXIMATE WEIGHT OF FIXTURE IS 2 LBS PER FOOT OF LENGTH.
4. REFER TO PAGE 3 FOR LENS INSTALLATION/REMOVAL INSTRUCTIONS.
3.56"
3.69"
2.00"
CEILING
REFERENCE
BELL LENS
SHOWN
CROSS SECTION VIEW
SIDE VIEW - ROW MOUNTED
SIDE VIEW - INDIVIDUALLY MOUNTED
END CAP END CAP
FEED AIRCRAFT
CABLE AIRCRAFT CABLE
.38" TYP
FIXTURE LENGTH
(24", 36", 48", 72", OR 96")
FEED AIRCRAFT
CABLE AIRCRAFT
CABLE AIRCRAFT
CABLE AIRCRAFT
CABLE AIRCRAFT
CABLE
END
CAP END
CAP
.38"
TYP
FIXTURE LENGTH
MINUS .75"
FIXTURE LENGTH
MINUS .75" FIXTURE
LENGTH
- SCREWDRIVER/DRILL
- 11/32" NUT DRIVER

litecontrol.com
DO NOT MODIFY OR ALTER THIS PRODUCT IN ANY WAY, OR INSTALL IN ANY FASHION WHICH IS CONTRARY TO THE INSTRUCTIONS CONTAINED HEREIN.
IF YOU HAVE ANY QUESTIONS REGARDING THIS PRODUCT OR THE INSTALLATION OF IT, PLEASE CALL LITECONTROL ENGINEERING AT 781-294-0100.
DRAWING: 510641
REV / DATE: 0 / 1/16/2019
INSTALLATION INSTRUCTIONS
FIXTURE SERIES: 67L MOUNTING TYPE: AIRCRAFT CABLES PAGE: 2 OF 3
REMOVE LENS, REFERRING TO PAGE 3. LOCATE AIRCRAFT CABLES ALONG
STRAIGHT LINE IN CEILING PER DIMENSIONS SHOWN ON PAGE 1. REFER TO
CABLE INSTRUCTION SHEET 510541 FOR ATTACHMENT TO CEILING.
INSERT FLAT STRAP INTO
CHANNEL IN HOUSING
(MARKED IN BLUE). INSERT
CABLE GRIPPER THROUGH
HOUSING AND THREAD INTO
FLAT STRAP. REPEAT AT EACH
CABLE LOCATION.
AT END OF FIXTURE, INSERT
FLAT STRAP COMPLETELY
INTO HOUSING SUCH THAT
CABLE GRIPPER IS THREADED
INTO HOLE A. AT FIXTURE
JOINT, INSERT FLAT STRAP
PARTIALLY SUCH THAT HOLE B
IS USED.
RAISE FIXTURE (1ST FIXTURE OF ROW) UP TO
CEILING. ATTACH TO AIRCRAFT CABLE
REMOVE 5/8" PLUG BUTTON AT FEED LOCATION.
INSERT UNIVERSAL BUSHING INTO FEED HOLE
AND ROUTE FEED CORD THROUGH BUSHING
INTO FIXTURE WIREWAY. MAKE ELECTRICAL
CONNECTIONS.
RAISE NEXT FIXTURE IN ROW; ATTACH TO AIRCRAFT
CABLE IN CEILING. ROUTE WIRING THROUGH FIXTURE
JOINT AS SHOWN. INSERT PROTRUDING FLAT STRAP OF
PREVIOUS FIXTURE INTO CHANNEL OF NEW FIXTURE.
SECURE BY INSERTING 1/4-20 MACHINE SCREW
THROUGH HOUSING TOP AND FLAT STRAP.
SECURE JOINT USING (2) 8-32 MACHINE SCREWS AND
NUTS. DO NOT TIGHTEN UNTIL FIXTURES ARE ALIGNED;
LEVEL BY SLIDING CABLE GRIPPERS UP/DOWN. REPEAT
STEPS 3-4 FOR EACH ADDITIONAL FIXTURE IN ROW.
IF INSTALLING INDIVIDUAL FIXTURE: LEVEL
FIXTURE BY SLIDING CABLE GRIPPERS UP/DOWN.
SKIP TO STEP 5.
ATTACH END CAP AT BOTH ENDS OF FIXTURE OR ROW OF
FIXTURES USING (2) #8 X 1/4" LONG SHEET METAL SCREWS.
ENSURE END CAP IS FLUSH WITH HOUSING WALLS.
CLEAN FIXTURE EXTERIORS WITH GENERAL WINDOW
CLEANER. REATTACH LENS PER PAGE 3.
12
345
B
A
FLAT
STRAP
CABLE GRIPPER
BUSHING
5/8" FEED
HOLE (PLUG
REMOVED)
FEED
CORD
FLAT
STRAP
1/4-20 MS
8-32 MS
NUT
(LED REFLECTOR
MODULES HIDDEN
FOR CLARITY.)
END
CAP
#8 SMS

litecontrol.com
DO NOT MODIFY OR ALTER THIS PRODUCT IN ANY WAY, OR INSTALL IN ANY FASHION WHICH IS CONTRARY TO THE INSTRUCTIONS CONTAINED HEREIN.
IF YOU HAVE ANY QUESTIONS REGARDING THIS PRODUCT OR THE INSTALLATION OF IT, PLEASE CALL LITECONTROL ENGINEERING AT 781-294-0100.
DRAWING: 510641
REV / DATE: 0 / 1/16/2019
INSTALLATION INSTRUCTIONS
FIXTURE SERIES: 67L MOUNTING TYPE: AIRCRAFT CABLES PAGE: 3 OF 3
LENS REMOVAL AND INSTALLATION
LENS REMOVAL
LENS INSTALLATION
PLACE FIXTURE ON FLAT
AND SECURE SURFACE.
STARTING AT ONE END OF
FIXTURE, GENTLY SQUEEZE
SIDES OF LENS.
MOVING ALONG LENGTH OF
FIXTURE, CONTINUE TO GENTLY
SQUEEZE SIDES OF LENS,
RELEASING LENS LIP FROM
HOUSING.
AS LENS LIP TO DETACHES FROM
HOUSING, PIVOT LENS TO ONE
SIDE.
GENTLY WORK LENS OUT OF END
HEADERS.
WITH FIXTURE INSTALLED AND
END CAPS ATTACHED, ALIGN
LENS WITH HOUSING AT AN
ANGLE.
PIVOT LENS INTO HOUSING
AROUND END HEADERS.
GENTLY WORK LENS INTO
PLACE BETWEEN END
HEADERS. KEEP LENS
ALIGNED WITH HOUSING.
STARTING FROM ONE END OF
FIXTURE AND THEN MOVING
ALONG LENGTH OF FIXTURE,
GENTLY SNAP LENS INTO PLACE.
TO ENSURE SECURE FIT, FEEL
ALONG THE SEAM BETWEEN
LENS AND HOUSING FOR ANY
MISALIGNMENT.