HumanCentric XT Series Setup guide

Fits VESA patterns 100mm x 100mm and 75mm x 75mm. If your monitor doesn’t have VESA holes, check
www.humancentric.com for an appropriate adapter for your model.
Models 101-3001 (single), 101-3002 (dual)
TOOLS INCLUDED
M6 Large Allen Wrench
XT-Series Monitor Mount
Patented in the US, International Patents Pending
TECHNICAL SPECIFICATIONS
Dual arm socket
Single
Arm
Dual
Arm
9 kg per arm
N/A 100036003600240010500 - 540 mm 0 - 270mm 9 kg
160 mm 3600360024001050
Lift Angle Pivot Swivel Pan Tilt Extension Vertical Max Weight
Load
Monitor Screws (4)
Base and pole Clamp Padding Lower Arm Upper Arm Monitor Bracket
Monitor Screws (8)
Clamp Padding Lower Arms (2) Upper Arms (2) Monitor Brackets (2)
Base and pole
with clip
PARTS INCLUDED
SINGLE ARM
DUAL ARM
COMPATIBLE WITH MODELS
M6 M3
M3 Small Allen Wrench
© 2017 HumanCentric Ventures LLC www.humancentric.com
0 - 21 in 0 - 10.5 in
0 - 540 mm 0 - 270 mm
0 - 21 in 0 - 10.5 in
1000
6.3 in
19.8 lbs
19.8 lbs per arm
1

2. INSTALL LOWER ARMS
Install and tighten
the adjustable clamp
as shown. Insert the
M3 allen wrench into
the wrench slot.
click!
DUAL MOUNT
SINGLE MOUNT
click!
Place the clamp
padding between
the desk and the
intended clamp
location. For
optional permanent
placement, remove
the adhesive
backing.
Place the clamp
padding between the
desk and the intended
clamp location. For
optional permanent
placement, remove the
adhesive backing.
Desk Thickness: 20 - 110 mm (0.8 - 4.3 in)
GROMMET OPTION
CLAMP OPTION
1. INSTALL BASE
Disassemble clamp
base as shown. Desk Thickness: 20 - 60 mm (0.8 - 2.35 in)
Hole Diameter: 10-60 mm (0.4 - 2.35 in)
© 2017 HumanCentric Ventures LLC www.humancentric.com
2

2. INSTALL UPPER ARMS 3. INSTALL MONITOR
The black screw goes
toward the bottom of the monitor
Slide the upper arm(s) onto the
lower arm(s) until the lock clicks
into place.
click!
click!
4. ROUTE CABLES WARNING
Without the monitor weight to hold
the spring in place, the monitor arm
could swing upward and cause
personal injury.
Please make sure that the monitor
arm is in the highest possible position
when mounting or removing the
monitor.
© 2017 HumanCentric Ventures LLC www.humancentric.com
3

To adjust the swing tension of the arms,
tighten or loosen the set screws with the
M3 allen wrench.
5. ADJUSTMENTS
To adjust the tension for the monitor’s tilt
and rotation, tighten or loosen the monitor
bracket tension screw appropriately.
To adjust the spring tension for your
monitor, raise the monitor up to the
highest position and insert the M6 allen
wrench into the gap at the top of the arm.
To increase the tension for heavier
monitors, loosen the screw. To decrease
the tension for lighter monitors, tighten
the screw.
DUAL MOUNT
M6 M3
M3
M3
For heavier monitors, turn
counter-clockwise.
For lighter monitors, turn clockwise.
© 2017 HumanCentric Ventures LLC www.humancentric.com
4