HumanCentric 101-4002 User manual

Fits TVs with VESA patterns from 75mm x 75mm to 400mm x 400mm.
Model 101-4002
ADDITIONAL TOOLS REQUIRED
Wall Mount for 23” - 55” TVs
www.humancentric.com/patents
PARTS INCLUDED
MOUNTING ARM
COMPATIBLE WITH MODELS
© 2017 HumanCentric Ventures LLC www.humancentric.com
Phillips Head Screwdriver
Power drill with ⅜” bit (solid concrete or concrete block) or 3/16” bit (wood stud)
Level
Marking Pencil
Edge-finding stud locator (for stud wall mounting)
Masking tape (to plan mounting location)
VESA EXTENSION ARMS
TOOLS
A Mounting Arm and Plate with Center Cover (1)
FM4 Allen Wrench (1)
B Wall Plate Top / Bottom Covers (2)
W-A Wall Mounting Screws (4) W-B Concrete Wall Anchors (4)
Warning: Not for use with drywall!
W-C Wall Mounting Washers (4)
M-E M8 x 50mm (4) M-H Small Spacer (8)
M-I Large Spacer (8)
Fits 23''-55'' TVs up to 35 kg (77 lbs)
Note: Not all parts will be used in the installation. Multiple configuration options are provided to fit dierent TVs, and
dierent parts are used for dierent configurations.
Needed for displays with VESA patterns above 200 x 200
C Extension Arms (4)
D Extension Arm Screws (4)
EExtension Arm Nuts (4)
WALL MOUNTING HARDWARE
TV MOUNTING HARDWARE
M-A M5 x 14mm (4)
M-B M6 x 14mm (4)
M-C M6 x 30mm (4)
M-D M8 x 30mm (4) M-G D8 (4)
M-F D5 (4)
GWrench
1

© 2017 HumanCentric Ventures LLC www.humancentric.com
2. ATTACH MOUNTING ARM TO WALL
1. REMOVE MOUNTING PLATE FROM MOUNTING ARM
Use the included wrench to loosen the top two nuts and
completely remove the bottom nut on the back of the
mounting plate.
Pull the bottom of the plate away from the mounting
arm and lift the plate up to remove it from the arm.
Read the entire instruction manual, including the warnings at the end of the manual, before you start installation and
assembly. If you have any questions regarding any of the instructions or warnings, please contact the HumanCentric
support team for assistance at [email protected]
CAUTION
Use with products heavier than the maximum weights indicated may result in damage to the mounted devices or
personal injury.
IMPORTANT
Ensure that you have received all parts according to the parts list prior to installation. If any parts are missing or
damaged, please contact the HumanCentric support team for replacements at [email protected]
2A.Determine VESA Mounting Pattern
Place the mounting plate on the back of your TV. If
the holes lines up with the holes in the bracket,
proceed to step 2b. If the holes are bigger than the
plate, install the extension arms.
200mm 200mm
200mm
200mm
No extension arms needed Extension arms needed
2. ATTACH MOUNTING PLATE TO TV
2

© 2017 HumanCentric Ventures LLC www.humancentric.com
2B. Select Screws and Spacers
Hang tight - this step can take some trial and error to
find the right combination!
If the mounting bracket lays flat on the
back of the TV and the mounting holes
on the TV are not inset, then you may
not need to use any spacers (depending
on screw length).
If it doesn’t lay flat on the
TV, if the holes are inset,
or if there are other
obstructions like cables,
then you must use the
large and small spacers
between the TV and the
bracket to create a flat,
even surface.
Gently hand-tighten the screws to reach the end of the
hole, and take note of how far the screws stick out.
Ensure that you choose
an appropriate length
screw and spacer
combination that is not
too long or too short:
Will not hold TV Will damage TV
First, try dierent size screws included with the mounting
kit (M-A to M-E) to determine the correct screw diameter
for your TV.
Screw Diameters
M-A
M-B, M-C
M-D, M-E
5mm
6mm
8mm
Next, lay the mounting bracket on the back of the TV.
Flat back
Round back
You may need to use up to
two large and two small
spacers on each screw to
achieve the proper fit.
If your mounting pattern is larger than 200 x 200, you
will need to use the included extension arms to extend
the mounting plate size.
Attach the extension arms to the corners of the mounting
plate as needed for your VESA pattern:
2. ATTACH MOUNTING PLATE TO TV
400mm
300mm
400mm
300mm
400mm
300mm
200mm
400mm
300mm
3

However, your optimal placement might vary
(especially with larger TVs), so we suggest creating
an outline on the wall with masking tape where you
want your TV to be. Based on that location, determine
the proper placement of the mounting holes.
Centered at eye level
42” (average)
3A. Determine Mounting Height
Continue to the appropriate step for your wall type:
2B-1: Wood Stud Wall
2B-2: Solid Concrete or Concrete Block
Do not use wall anchors in drywall or wood stud walls.
3. ATTACH MOUNTING ARM TO WALL
The ideal height for a typical TV room setup is for the
middle of the TV to be 42” o the ground.
Warning:
© 2017 HumanCentric Ventures LLC www.humancentric.com
Hold the mounting arm against the wall with the arrow pointing up,
and use the level to confirm that the mount is properly aligned.
Mark the three mounting holes with a pencil.
Locate a stud in the wall with the edge-finding stud finder.
Ensure that you locate and mark the center of the stud.
2C. Attach Mounting Plate to TV
55mm
Use a 3/16” (4.5mm) drill bit to make three 2.2”
(55mm) deep holes in the wall.
2. ATTACH MOUNTING PLATE TO TV
Using the screw / spacer combination
you selected in the previous step, attach
the mounting plate to the back of the TV.
Remember - the two bolts on the back of
the mounting plate should be towards
the top of the TV.
3B1. ATTACH MOUNT TO WOOD STUD WALL
4

Use three wall mounting screws (W-A) and washers
(W-C) to secure the arm to the wall.
60mm
Hold the mounting arm against the wall with the arrow pointing
up, and use the level to confirm that the mount is properly
aligned. Mark the four mounting holes with a pencil.
Use a 3/8” (10mm) drill bit to make four 2.4”
(60mm) deep holes in the wall.
Use four wall mounting screws (W-A), wall anchors
(W-B), and washers (W-C) to secure the arm to the wall.
Ensure that the mounting arm is securely fastened
to the wall before continuing on to the next step!
Ensure that the mounting arm is securely fastened
to the wall before continuing on to the next step!
© 2017 HumanCentric Ventures LLC www.humancentric.com
3B2. MOUNT TO SOLID CONCRETE OR CONCRETE BLOCK WALL
3B1. ATTACH MOUNT TO WOOD STUD WALL
5

© 2017 HumanCentric Ventures LLC www.humancentric.com
4. ATTACH TV TO MOUNTING MOUNT
3C. Attach Wall Plate Covers
First, attach the center wall
plate cover. Then, slide on
the top and bottom covers as
shown.
Ensure that the two top nuts are still attached to the back
of the mounting plate, but are loose enough to slide the
arm attachment under the nuts.
When the TV is correctly positioned, tighten the
three nuts on the back of the mounting plate.
While securely holding the TV in place, confirm that the TV is level. The
notches in the arm attachment are wide enough to adjust the TV +/- 3°
to the right or left.
Note: The covers have small tabs that attach to notches in
the metal. When positioned correctly, they will securely clip
into place - but it can take a few tries!
2
1
2
Have a friend help you lift the TV and carefully
lower the mounting plate onto the notches in
the arm. Then allow the lower bolt to slide in
through the bottom hole in the mounting plate.
3. ATTACH MOUNTING ARM TO WALL
6

Enjoy your new mounted TV:) If you need anything, please let us know!
Any questions? Contact us at [email protected] , and we’re happy to help!
6. ADJUST TILT
7. ENJOY!
© 2017 HumanCentric Ventures LLC www.humancentric.com
5. ROUTE CABLES
Use the allen wrench to loosen the adjustment screw on the tilt mechanism. Tilt the TV to the desired
angle and re-tighten the adjustment screw.
After plugging in your cables, remove the decorative arm
covers on the bottom of the arms.
Route the cables through the arm covers and
replace the covers on the arms.
7

© 2017 HumanCentric Ventures LLC www.humancentric.com
WARNINGS
The wall must be capable of supporting five times the weight of the device (such as a TV) and mount combined
Mounts must be attached as specified in the instruction manual. Improper installation may result in damage or serious personal injury.
Safety gear and proper tools must be used. This product should only be installed by those with the necessary skills to install the
hardware. If you do not have the necessary skills, installation should be handled by a professional.
Use the mounting screws provided and do not over-tighten the mounting screws
This product contains small items that can be a choking hazard if swallowed. Keep these items away from children.
Do not use this product for any purpose not explicitly specified by manufacturer
This product is intended for indoor use only. Using this product outdoors could lead to product failure or personal injury.
Manufacturer is not responsible for damage or injury caused by incorrect assembly or use.
Check that the mount is secure and safe to use at regular intervals (at least every three months).
HumanCentric intends to make this manual accurate and complete. However, HumanCentric makes no claim that the information
contained herein covers all details, conditions, or variations. Nor does it provide for every possible contingency in connection with the
installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind.
HumanCentric makes no representation of warranty, expressed or implied, regarding the information contained herein. HumanCentric
assumes no responsibility for accuracy, completeness or suciency of the information contained in this document.
8