Hunter Pacific Coolah Instruction Manual

ELECTRICIANS - TO PROTECT YOUR CUSTOMER’S WARRANTY, PLEASE READ
PAGE 2 OF THIS BOOKLET PRIOR TO THE INSTALLATION OF THIS PRODUCT.
CEILING FAN MUST BE INSTALLED
BY A LICENSED ELECTRICIAN
(NO OTHER PERSONS SHOULD ATTEMPT TO INSTALL THIS FAN)
*After installation, electricians must tick off all items on the quick
checklist and fill out their details towards the back of this Installation and
User Manual.
®
Warranty Procedure*
For online warranty bookings visit: www.hunterpacific.com.au (24hours, 7 days)
For technical advice call: 1300 360 280 (Monday to Friday from 9am to 5pm EST)
* Warranty only available within Australia. See page 16.
The fan should only be installed and used indoors. Not
suitable for outdoor use and not recommended for
coastal locations.
Installation & User Manual

2
IMPORTANT INFORMATION
ELECTRICIANS MUST READ PRIOR TO INSTALLATION
1. Distributor and installer details and purchase receipts are essential for on-site warranty claims
and must be presented to repair personnel. A page towards the back of this manual has been
allocated to allow you to record these details.
2. Fans and fixed wiring products must only be installed by persons who are appropriately licensed
by the applicable State regulatory body. Therefore, to protect our repair personnel, on-site
warranty claims will not be accepted if products have been installed by unlicensed persons.
3. Damage caused by incorrect installation, force-majeure, electrical surges, lightning, power grid
fluctuations, water or by connection to alternative power supply sources (such as solar inverters,
etc.) is not eligible for warranty repair.
4. Blades must be replaced only as a complete set. Blades are supplied only as a pre-balanced set
and the replacement of individual blades may void the warranty by causing mechanical damage
to the motor, excessive noise or premature wear.
5. When products are installed in a location requiring special access equipment (such as
scaffolding or scissor lifts, etc) the cost of providing, installing and operating special access
equipment must be borne by the site owner.
6. “This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been giv-
en supervision or instruction concerning use of the appliance by a person responsible for their
safety. Children should be supervised to ensure that they do not play with the appliance.” (AS/
NZS 60335.1 C1.7.12)
DANGER: Contact with ceiling fan blades can cause serious injury or death.
To electricians and installers. The Australian Competition and Consumer Law 2010 mandates
consumer protection against defects or poor workmanship in provision of services (such as
installing a ceiling fan). To protect yourself and the consumer these instructions must be
followed. Failure to do so may result in the consumer making a claim against you for
consequential loss or damage.
7. A double pole isolation switch providing full disconnection of both fan and light must be fitted in
accordance with the wiring rules (AS/NZS 60335.1 C1.7.12.2).
For safety, and to protect your customers warranty, the following must be taken into
account when installing and operating the product(s):
IF THERE ARE ANY PROBLEMS WITH THE PRODUCT AT TIME OF
INSTALLATION THE INSTALLER MUST CONTACT THE TECHNICAL
ADVICE LINE NUMBER 1300 360 280 BEFORE LEAVING THE JOB
SITE. PLEASE DO NOT REMOVE THE FAN FROM THE CEILING
ONCE INSTALLED UNLESS INSTRUCTED TO DO SO.
(a) DO NOT USE SOLID-STATE WALL CONTROLLERS. Neither leading nor lagging edge
controllers will give satisfactory performance. Wall controls must only be types approved
for use by Hunter Pacific International.
(b) The fan, light and bracket must be earthed.
(c) Fan and light must be run from the same final circuit.
(d) Mounting bracket must be firmly screwed to a solid structure such as a concrete ceiling,
steel structure or timber framing. If additional bracing is added it must be firmly secured to
the rafters and not left floating on the ceiling. Special mounts, such as T-hooks, are
available for certain types of installation. DO NOT USE COUNTERSUNK SCREWS.
(e) After installation, fan blades must be at least 2.1 m (7 feet) above floor level.
(f) The use of these products by children and the infirm must be under supervision.

3
Parts List - Majestic Coolah
Part Qty Part Qty Part Qty
Hanger Bracket 1Down Rod Pin 1Blades 4
Bracket Screws 2Down Rod Cotter Pin 1Blade Holders 4
Ball Joint 1Down Rod Screws 1Blade Holder Screws 8
Ball Joint Pin 1Canopy Cover Screws 2Blade Screws 12
Ball Joint Screw 1Canopy Cover 1Blade Screw Washers 12
Down Rod
(21mm Diameter) 1Motor Housing 1Switch Housing Bottom Cover 1
Pull cord Assembly Kit (comes preassembled - 1x pull cord assembly, 1x motor-run capacitor,
1x speed capacitor, 1x pull chain, 3x screws and 1x 2 pin plug).
Installation & User
Manual
®
Blade Washer & Screw
Blade
Blade Holder
Pull Cord Assembly Kit
Motor Housing
Canopy Cover
Down Rod
Ball Joint
Hanger Bracket
Blade Holder Screw
Blade Screw & Washer
Blade
Switch Housing Bottom Cover

4
IMPORTANT INFORMATION
The table below contains information that can help you quickly identify the product you are installing.
If you have any difficulties installing our product, we recommend you to call our Technical Advice
Line on 1300 360 280 for advice.
CODE SIZE FAN MODEL NAME COLOUR
830 132cm, (52”) Majestic Coolah White Motor & White Blades
with Rattan Insert
837 132cm, (52”) Majestic Coolah Antique Brass Motor &
Walnut Blades with Rattan Inset
1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not approved by
Hunter Pacific International for use with its fans. DO NOT use solid state controllers. The use of
unapproved controllers may void your warranty.
2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If only one
blade is damaged you are still required to replace with a new set.
Installation & User
Manual
®

5
1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not approved by
Hunter Pacific International for use with its fans. DO NOT use solid state controllers. The use of
unapproved controllers may void your warranty.
2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If only one
blade is damaged you are still required to replace with a new set.
Installation Instructions
(Assembling the fan)
Installation & User
Manual
®
Fig. 2
Fig. 1
1
2
3
1
2
3
4
5
6
Ø25mm
Ø1-1/8”
Timber
Nogging
Hanger
Bracket
Fig. 3 Fig. 4
Fig. 5

6
Wiring Instructions for use with wall control (not supplied)
1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not approved by
Hunter Pacific International for use with its fans. DO NOT use solid state controllers. The use of
unapproved controllers may void your warranty.
2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If only one
blade is damaged you are still required to replace with a new set.
WARNING: To comply with AS/NZS 60335.1 an Isolation switch must
be fitted in series with the supply of this product.
(an RCD may fulfill this function if suitably labeled)
Installation Instructions
(Assembling the fan)
Pull cord must be
set to high speed to
use wall control
Required when
using pull cord,
wall control or
remote control
Wall control must be set
to high speed to use
pull cord control. Controls on wall
plate (not supplied)
NOTE: Wall switch is not supplied with the fan.
Fig. 6
Installation & User
Manual
®

7
1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not approved by
Hunter Pacific International for use with its fans. DO NOT use solid state controllers. The use of
unapproved controllers may void your warranty.
2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If only one
blade is damaged you are still required to replace with a new set.
Installation Instructions
(Assembling the fan)
Installation & User
Manual
®
Fig. 6
1
2
3
Fig. 7
1
2
3
Fig. 8
Fig. 9

8
1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not approved by
Hunter Pacific International for use with its fans. DO NOT use solid state controllers. The use of
unapproved controllers may void your warranty.
2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If only one
blade is damaged you are still required to replace with a new set.
Installation Instructions
(Installing an Accessory Light Kit )
*Light Kit shown below is not HPI’s Product*
Installation & User
Manual
®
Fig. 10 Fig. 11
12
Fig. 12 Fig. 13
Trouble Shooting Tips - Light
 Light will not turn on - Make sure globe has not blown and is properly fitted. Check all
light wires in the light kit, the terminal block in the canopy cover and the wall switch have
been connected correctly.
 Light is not responding to remote control- Make sure globe has not blown. Check all
light wires in the light kit, the terminal block in the canopy cover and the remote receiver
have been connected correctly. Check dip switch settings in remote hand piece and
remote receiver correspond. Check handpiece battery.
 Light wires appear to be missing or too short - Wires may be stuck in the motor hous-
ing. Carefully pull wires out of the motor housing, careful not to strip the wires as this may
cause the fan to short.
 Light flickers or flashes - Check globe is secured properly. Check CFL or LED globes are
not defective, then recheck wiring.
 NOTE: DO NOT USE CFL OR LED GLOBES WITH LIGHT DIMMERS OR DIMMING
REMOTE CONTROLS
1
2
3

9
1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not approved by
Hunter Pacific International for use with its fans. DO NOT use solid state controllers. The use of
unapproved controllers may void your warranty.
2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If only one
blade is damaged you are still required to replace with a new set.
Installation Instructions
(Attaching an extension rod—Hunter Pacific rods to be used ONLY)
Installation & User
Manual
®
≥2.1m AU/NZ
1
2
3
1
2
3
11mm
χØ6.5mm
Top
End
Fan
End
χ = Holes must
be in centre of rod
and drilled straight
through.Crooked
or offset holes will
cause the fan to
wobble.
6
5
4
1
1
2
3

10
1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not approved by
Hunter Pacific International for use with its fans. DO NOT use solid state controllers. The use of
unapproved controllers may void your warranty.
2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If only one
blade is damaged you are still required to replace with a new set.
Trouble Shooting Tips for electricians
Fan will not start
 Check that the reversing switch is pushed into its Summer or Winter position.
 Check wire connections in the wall switch and terminal blocks, ensure all wires
are making proper contact.
 Check isolation switch is ‘on’.
 Check pull cord assembly is on either High, Medium or Low.
Fan is not responding to the remote control (if fitted)
 Check for flat battery. Make sure the dipswitch settings in the hand piece and the
remote receiver match.
 Check pull cord assembly is High position.
Fan is wobbling
 Check the ball joint slot is locked into the hanger bracket groove.
 Make sure blades are a matching set; the figures on matching sets of blades
should be identical with the numbers varying within 3 grams of each other.
 Check blade screws are tightened firmly. If necessary use balancing kit provided
to settle the wobble.
 Make sure bracket is tight against ceiling and the ceiling and the ceiling structure
are not moving.
 Check blade holder screws are tight.
Fan is noisy
 Check all screws and parts are secured firmly. Ensure there are no loose parts
moving inside the motor housing.
 Make sure the fan is installed with a Hunter Pacific International wall controller
only, do not use solid state controllers as they will cause unpleasant motor nois-
es.
Installation & User
Manual
®
Warranty Procedure*
For online warranty bookings visit: www.hunterpacific.com.au (24hours, 7 days)
For technical advice call: 1300 360 280 (Monday to Friday from 9am to 5pm EST)
* Warranty only available within Australia

11
General Maintenance
Changing Remote Batteries: - Batteries used in Handsets will weaken over time and should
be replaced every 6 months. Batteries removed from the Handset should be disposed
properly and kept out of reach of children.
* Before maintenance ensure fan is switched off at the isolation switch or circuit breaker *
Cleaning the Motor Housings: - Motor housings should be regularly cleaned to avoid build
up of dust. Dust will attract moisture and condensation leading to corrosion. Use a soft
damp (not wet) cloth to remove dust. Use only water and mild detergent. Spray cleaners
may damage coatings.
Cleaning the Blades: - Use a soft damp cloth to remove dirt from blades. Always dry blades
after cleaning. Blades should not be left damp or wet as this will damage blade finish or
cause corrosion. Use only water and mild detergent. Spray cleaners may damage coatings.
Always use soft cloths to clean blades and motor housings to avoid scratching painted and
plated finishes. Ideally your fan should be cleaned every 3 to 4 months.
If removing blades for cleaning then do so for each fan separately, do not mix blades from
different fans as this can upset the balance of the fan. Put blades back in the position they
came from.
Normal Wear and Tear: - Please note that a ceiling fan travels an enormous distance in the
course of its normal operation. Air is abrasive and suspended dust, high humidity and other
contamination will cause wear and tear of surfaces.
The use of fans under roofed decks and pergolas next to swimming pools and in coastal
areas will require increased maintenance due to the presence of chlorides (either as
common air borne salt spray or from compounds in pool chemicals)
The temperatures attained in the peak of a pitched deck or veranda roof can easily exceed
60-70°C and especially when coupled with chlorides this will increase maintenance
requirements. Even indoors in coastal areas the influx of warm, sea air can accelerate the
surface corrosion of metal parts. This can still happen a great many kilometres from the
sea.
When humidity is high and temperature drops moisture condenses on metal surfaces
including ceiling fans. The layer of moisture can be almost microscopic but it will affect the
surface by depositing a tiny layer of dissolved salts or airborne acidic compounds and thus
eventually leading to corrosion if the product is not properly and regularly cleaned. This
applies equally to indoor and outdoor fans.
LACK OF MAINTENANCE LEADING TO SURFACE CORROSION OR SIMILAR
DAMAGE IS NOT COVERED BY WARRANTY.
Installation & User
Manual
®
1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not approved by
Hunter Pacific International for use with its fans. DO NOT use solid state controllers. The use of
unapproved controllers may void your warranty.
2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If only one
blade is damaged you are still required to replace with a new set.

12
REV (Winter) Mode
In REV (Winter) mode your ceiling fan will spin the opposite direction. Air is drawn up
the centre of the fan, and pushed along the ceiling to circulate down to the living areas.
The REV (Winter) mode can also be for air circulation in a poorly ventilated rooms.
The direction the fan will spin in REV (Winter) when viewed from underneath will be
clockwise.
FWD (Summer) Mode
Ceiling fans are an environmentally smart choice to assist with cooling and warming your
home.
In FWD (Summer) mode your ceiling fan will spin to push air down the centre of the fan
producing a cooling breeze.
The direction the fan will spin in FWD (Summer) when viewed from underneath will be
anti-clockwise.
FWD (Summer) and REV (Winter) Modes Explained
Air is blown down,
producing a cool breeze
An upward airflow will push warm
air off the ceiling and circulate it
downwards
Direction fan will spin in FWD
(Summer) mode when viewed from
underneath
Direction fan will spin in REV
(Winter) mode when viewed from
underneath
Installation & User
Manual
®
1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not approved by
Hunter Pacific International for use with its fans. DO NOT use solid state controllers. The use of
unapproved controllers may void your warranty.
2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If only one
blade is damaged you are still required to replace with a new set.

13
Quick Checklist
1.
Ceiling fan is not installed to a solid-state wall controller. Neither leading nor
lagging edge controllers will give satisfactory performance. Wall controllers must
only be types approved for use by Hunter Pacific International.
2. The fan, fan light (if fitted) and bracket is earthed.
3. Fan and optional fan light are run from the same final circuit.
4.
Mounting bracket must be firmly secured to a solid structure such as a concrete
ceiling, steel structure or timber framing. If additional bracing is added it must be
firmly secured to the rafters and not left floating on the ceiling. Special mounts,
such as T-hooks, are available for certain types of installation.
5. Fan blades are at least 2.1m (7 feet) above floor level.
6. Check the fan is operating correctly on all three speeds using the pull cord or wall
controller.
7. If light is installed. Check light is working and light switch is functioning properly.
8. If remote control is installed. Check the fan (and light if installed) is responding to
the remote control.
9. A separate isolation switch has been installed.
10. Check electrician’s details have been recorded onto the page 14 of this manual.
Electricians make sure everything on this checklist is ticked off before you leave the installation site.
If you have trouble installing our product please refer to the trouble shooting section on the previous
page first then phone the Hunter Pacific Technical Advice Line on 1300 360 280 (open 9am to 5pm
EST). DO NOT uninstall the fan and DO NOT return fan to retailer without calling the support line
1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not approved by
Hunter Pacific International for use with its fans. DO NOT use solid state controllers. The use of
unapproved controllers may void your warranty.
2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If only one
blade is damaged you are still required to replace with a new set.
Installation & User
Manual
®

14
Please to fill out the product and purchase details
Fill out the details below and keep this manual. You will need to present your product
information, installing electricians license number and proof of purchase for warranty
claims.
CUSTOMER DETAILS
Customer Name:
Installation Site Address:
INSTALLING ELECTRICIAN DETAILS
Electrical company and Electrician Name:
License No:
Telephone:
Mobile:
Install Date:
PRODUCT DETAILS
Qty Product Name Install Area Colour Fan Sweep (i.e.
48”, 52”, 54” etc)
PURCHASE DETAILS
Qty Product Name Purchase Place Purchase Date
PLEASE RETAIN THE PURCHASE RECEIPT FOR WARRANTY CLAIMS
Installation & User
Manual
®
1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not approved by
Hunter Pacific International for use with its fans. DO NOT use solid state controllers. The use of
unapproved controllers may void your warranty.
2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If only one
blade is damaged you are still required to replace with a new set.

15
Attach receipt here.
Attach electricians invoice here.

16
Warranty Terms and Conditions
Manufacturer’s warranty covers defects in the product only. It does not cover defects within the fan
installation or improper maintenance. This warranty covers Australia only.
Warranty periods begin from the day of purchase from an authorised reseller or dealer. Warranty on
builder supplied and installed fans commences when fans are delivered to the builder or contractor
(which generally precedes hand over of the dwelling). Warranty periods are as follows:
ELECTRONIC PARTS WARRANTY
1 year in-home warranty on all electronic components such as control modules, remote control
systems, capacitors and lighting whether supplied as part of the complete product or as an
accessory (in-home warranty not available on user replaceable lamps and remote control handsets).
MOTOR AND MECHANICAL PARTS WARRANTY
2 years in-home warranty on mechanical parts and the motor, excluding cosmetic issues and
corrosion (unless reported in the first 3 months).
3 years additional parts warranty on the electric motor (excluding capacitors).
1 year warranty applies when fan or relevant part is used in any non-domestic applications.
This statement is required by the Australian Consumer Law 2010: “Our goods come with guarantees
that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or
refund for a major failure and for compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of
acceptable quality and the failure does not amount to a major failure.”
Please note carefully - If the product is found to be free of defects or the product is not
functioning properly as a result of faulty installation or lack of maintenance then Hunter
Pacific International Pty Ltd or its service agent reserve the right to charge a service fee to
rectify the reported problem.
Damage caused by incorrect installation, force-majeure, electrical surges, lightning, power grid
fluctuations, water or alternative power supply sources (such as solar inverters etc.) will not be
covered by warranty. This warranty does not cover the product being incorrectly used, physically
abused, accidentally damaged or not serviced in accordance with the maintenance instructions.
This product warranty excludes to the fullest extent possible under law any liability for consequential
loss or damages directly or indirectly resulting from a faulty ceiling fan or accessory product that is
not installed or maintained according to the installation instructions. When installed, maintained and
used according to the instructions such loss or damage can be easily avoided or minimised.
Signals (ripple control) sent through the power grid by the electricity supplier for the control of other
devices may cause intermittent noises and do not occur as a result of a fault in the fan.
When ceiling fans are installed in a location requiring special equipment (such as scaffolding or
scissor lifts) the cost of providing such equipment must be borne by the site owner in case of
maintenance and repair and such costs should be considered when deciding on fan placement.
WHS regulations may prohibit technicians from attempting to access products installed above a
certain height without special measures in-place. It is the site owners responsibility to provide those
measures at their own cost or an on-site/in-home warranty service may be refused. The product will
need to be removed and reinstalled at the owners expense.
PLEASE RETAIN THE PURCHASE RECEIPT FOR WARRANTY CLAIMS

17
BLANK PAGE

18
BLANK PAGE

19
BLANK PAGE

52CLHIMV1.2
Warranty Procedure*
For online warranty bookings visit: www.hunterpacific.com.au (24hours, 7 days)
For technical advice call: 1300 360 280 (Monday to Friday from 9am to 5pm EST)
* Warranty only available within Australia