Hunter Pacific Concept User manual

Electrician Installation Manual
Concept Ceiling Fan
(Timber and Moulded Blades)
1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not
approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The
use of unapproved controllers will void your warranty.
2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If
CEILING FAN MUST BE INSTALLED
BY A LICENSED ELECTRICIAN
(NO OTHER PERSONS SHOULD ATTEMPT TO INSTALL THIS FAN)
*Electricians are recommended to tick off all items on the quick
checklist and fill out their details onto the back page of the Fan
Owner Warranty & Operations Manual after installation
National Warranty Line
1300 360 280
ELECTRICIANS - TO PROTECT YOUR CUSTOMER’S WARRANTY, PLEASE READ
PAGE 2 OF THIS BOOKLET PRIOR TO THE INSTALLATION OF THIS PRODUCT.

Electrician Installation Manual
Concept Ceiling Fan
(Timber and Moulded Blades)
1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not
approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The
use of unapproved controllers will void your warranty.
2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If
only one blade is damaged you are still required to replace with a new set.
IMPORTANT INFORMATION
ELECTRICIANS MUST READ PRIOR TO INSTALLATION
1. Distributor and installer details and purchase receipts are essential for on-site warranty claims
and must be presented to repair personnel, make sure you record your details in the Fan Owner
Warranty and Operations Manual.
2. Fans and fixed wiring products must only be installed by persons who are appropriately licensed
by the applicable State regulatory body. Therefore, to protect our repair personnel, on-site
warranty claims will not be accepted if products have been installed by unlicensed persons.
3. Damage caused by incorrect installation, force-majeure, electrical surges, lightning, power grid
fluctuations, water or by connection to alternative power supply sources (such as solar inverters,
etc.) is not eligible for warranty repair.
4. Blades must be replaced only as a complete set. Blades are supplied only as a pre-balanced set
and the replacement of individual blades may void the warranty by causing mechanical
damage to the motor, excessive noise or premature wear.
5. When products are installed in a location requiring special access equipment (such as
scaffolding or scissor lifts, etc) the cost of providing, installing and operating special access
equipment must be borne by the site owner.
For safety, and to protect your customers warranty, the following must be taken into
account when installing and operating the product(s):
IF THERE ARE ANY PROBLEMS WITH THE PRODUCT AT TIME OF
INSTALLATION THE INSTALLER MUST CONTACT THE WARRANTY
HOT LINE NUMBER 1300 360 280. BEFORE LEAVING THE JOB
SITE. PLEASE DO NOT REMOVE THE FAN FROM THE CEILING
ONCE INSTALLED UNLESS INSTRUCTED TO DO SO.
(a) DO NOT USE SOLID-STATE WALL CONTROLLERS. Neither leading nor lagging edge
controllers will give satisfactory performance. Wall controls must only be types approved
for use by Hunter Pacific International.
(b) The fan, light and bracket must be earthed.
(c) Fan and light must be run from the same final circuit.
(d) Mounting bracket must be firmly screwed to a solid structure such as a concrete ceiling,
steel structure or timber framing. If additional bracing is added it must be firmly secured to
the rafters and not left floating on the ceiling. Special mounts, such as T-hooks, are
available for certain types of installation.
(e) After installation, fan blades must be at least 2.1 m (7 feet) above floor level.
(f) The use of these products by children and the infirm must be under supervision.
2

Electrician Installation Manual
Concept Ceiling Fan
(Timber and Moulded Blades)
1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not
approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The
use of unapproved controllers will void your warranty.
2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If
only one blade is damaged you are still required to replace with a new set.
Hanger Bracket
Hex Head Screw
Ball Joint
Canopy Cover
Parts List
Concept 2 Ceiling Fan Parts List
Part Qty Part Qty Part Qty
Blades 4 Base Plate 1 Canopy Cover Screws 2
Blade Screws 12 HPI Wall Controller 1 Canopy Cover 1
Blade Washers 12 Hanger Bracket 1 Motor Housing 1
Wall Speed Capacitor 1 Hex Head Screw 2
Ball Joint 1 15cm Down Rod 1 Reversing Switch Cover 1
Ball Joint Screw 1 Down Rod Pin Screw 1
Ball Joint Pin 1 Down Rod Short Screw 1
(these parts come preassembled)
Blade
Blade Screw
Base Plate
Motor
Housing
3

Electrician Installation Manual
Concept Ceiling Fan
(Timber and Moulded Blades)
1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not
approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The
use of unapproved controllers will void your warranty.
2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If
only one blade is damaged you are still required to replace with a new set.
STEP 3 (Fig. 3)
a) Check if the ball joint grub screw is tight.
b) Hang the ball joint into the hanger bracket.
Ensure the groove on the hanger bracket is
locked into the slot on the ball joint.
(This is important to ensure the fan will not
wobble and the weight of the fan is supported).
Assembling the fan
STEP 2 (Fig. 2)
a) Drill a hole in the timber nogging for wiring.
b) Secure the hanger bracket onto the timber
nogging, using the two hex head screws
provided. The timber nogging should be supplied
by the installing electrician and must be
supported between the two ceiling joists as
shown in the diagram above.
STEP 1 (Fig. 1)
PERFORM THIS STEP IF THE WIRES HAVE NOT
BEEN FED THROUGH THE DOWN ROD.
a) Loosen the ball joint screw and remove the
ball joint pin to separate the down rod from the
ball joint.
b) Feed wires from motor housing up and
through the down rod.
c) Insert the down rod pin screw through the
connection collar and the down rod (avoid
pinching wires). Tighten down rod pin screw.
Secure down rod with the other shorter down
rod screw provided.
d) Slide on canopy cover, refit the ball joint and
tighten grub screw.
Hanger
Bracket
Down Rod
Fig. 2
Timber Nogging
Hex Head Screw
Hanger
Bracket
Fig. 3
Down Rod
Down Rod
Pin Screw
Canopy
Cover
Connection Collar
Motor
Housing
Fig. 1

Electrician Installation Manual
Concept Ceiling Fan
(Timber and Moulded Blades)
1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not
approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The
use of unapproved controllers will void your warranty.
2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If
only one blade is damaged you are still required to replace with a new set.
(Assembling the fan )
Fig. 4
Green
Earth Wires
STEP 4 (Fig 4 & 5)
a) Connect wires from the fan to wires in the
ceiling via the terminal block on the hanger
bracket (refer to figure 4 and 5).
b) Make sure earth wires are also connected.
c) Connect light wires (red/white) if a light
fitting is going to be used. (Cap seal light
wires if a light fitting is not going to be used).
Wiring Instructions (with and without accessory light)
Brown
Blue
Red/White Earth Wires
Supply
E N A
LA LA
FA LA E N
Green-yellow
Black
Red
Red
Red
Brown
White or Red
Green-yellow
Blue
Fan Wiring
Combi
Control
Separate
Control
Separate terminal
For when 3 pole
block is fitted.
Wiring for use with 3 pole block
- Colours representative only
- Separate terminal required active for
light when 3 pole block fitted.
Fig. 5
STEP 5 (Fig 6)
a) Slide canopy cover up and over the hanger
bracket.
b) Loosen the canopy to locate screws holes then
loosen canopy screws half way.
c) Now twist the canopy cover in the opposite
direction and fully tighten screws until the canopy
cover is stabilized.
Fig. 6
Hanger Bracket
Canopy
Canopy Cover Screws

Electrician Installation Manual
Concept Ceiling Fan
(Timber and Moulded Blades)
1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not
approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The
use of unapproved controllers will void your warranty.
2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If
only one blade is damaged you are still required to replace with a new set.
Assembling the fan
Canopy
Screw Cover
STEP 6 (Fig 7)- Concept 2 fan ONLY
Move the canopy screw cover upwards towards the
canopy and turn it to secure the cover onto the screw
heads.
Fig. 7
Fig. 8 STEP 7 (Fig 8)
a) Push the base plate upwards and turn until the
tabs unlock to remove it.
b) Once the base plate is removed, the internal
blade carriers will be exposed. Insert blades and at-
tach them to the motor housing as shown in figure 8.
c) Tighten the 3 blade screws firmly but do not over
tighten.
d) Install blades for each fan individually, do not mix
blades from different fans as this will up set the bal-
ance of the fan.
Blade
Blade Screw
Motor Housing
tabs
Base Plate
Fig. 9
Tab slots
Tabs
Base Plate
STEP 8 (Fig. 9)
a) Once all blades are attached to the motor
housing, refit the base plate. The tabs
should lock in to place ensuring the base
plate is securely attached to the motor
Fig. 10
Reverse
Switch
STEP 9 (Fig. 10)
a) Reverse switch should be in the down position
for Summer (fan spins anticlockwise) and in the
up position for Winter (fan spins clockwise).
b) Make the sure reverse switch is not stuck in its
neutral position otherwise the fan will not spin.

Electrician Installation Manual
Concept Ceiling Fan
(Timber and Moulded Blades)
1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not
approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The
use of unapproved controllers will void your warranty.
2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If
only one blade is damaged you are still required to replace with a new set.
Attaching a Concept light kit - 78mm halogen light (MAX 100W)
Fig. 12
Tab
Slots
Light Wires
Light
Assembly Kit
Globe
STEP 2 (Fig. 12)
a) Use the connectors to attach the light wires from
the motor housing to the light wires on the light
assembly.
b) Secure the light assembly kit using the 3 screws
provided.
c) Plug the light globe into the socket. DO NOT
touch the light globe with your fingers, use a
tissue or a clean cloth. It is extremely important
to keep the globe clean. If the globe is dirty, clean
it carefully with a cloth or tissue. Dirt on the globe
will cause it to fail almost immediately.
NOTE: Do not use globes other than the specified
ones.
Motor
Housing
Tab
Slots
Tabs
Base Plate
STEP 1 (Fig. 11)
Push the base plate upwards and turn until the
tabs unlock to remove it.
Fig. 11
Screw
Light
Kit Ring
Light
Rim
Fig. 13 STEP 3 (Fig. 13) - Concept 2 fan ONLY (pre Nov
2008 Only)
a) Remove the screws attached to the light rim.
b) Remove the light kit ring from the light rim.
P.S . Adaptor ring not required for New
Concept 1 or New Concept 2 (Nov 2008)

Electrician Installation Manual
Concept Ceiling Fan
(Timber and Moulded Blades)
1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not
approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The
use of unapproved controllers will void your warranty.
2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If
only one blade is damaged you are still required to replace with a new set.
Attaching a Concept light kit - 78mm halogen light (MAX 100W)
Tab
Slots
Glass Cover
Fig. 16
Tabs
STEP 6 (Fig. 16)
a) Once globe is placed into its socket properly,
the glass cover can be fitted on to the fan.
b) Gently push the glass cover upwards and turn it.
The tabs should lock in to place ensuring the glass
cover is securely attached to the motor housing.
Light
Kit Ring
Light
Rim
Adaptor
Ring
Fig. 14 STEP 4 (Fig. 14) - Concept 2 fan ONLY
a) Place the adaptor ring on the light rim.
b) Place the light kit ring on the adaptor ring.
Light
Rim
Screw
Adaptor
Ring
Fig. 15 STEP 5 (Fig. 15) - Concept 2 fan ONLY
Use screws to attach the light ring and adaptor
ring firmly to the light rim.

Electrician Installation Manual
Concept Ceiling Fan
(Timber and Moulded Blades)
1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not
approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The
use of unapproved controllers will void your warranty.
2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If
only one blade is damaged you are still required to replace with a new set.
Attaching a Concept light kit - E14 light (2x40W)
Tab
Slots
Tabs
Base Plate
STEP 1 (Fig. 17)
Push the base plate upwards and turn until the
tabs unlock to remove it.
Fig. 17
Fig. 18
Tab
Slots
Light Wires
Light
Assembly Kit
Globe
STEP 2 (Fig. 18)
a) Use the connectors to attach the light wires from
the motor housing to the light wires on the light
assembly.
b) Secure the light assembly kit using the 3 screws
provided.
c) Install light globes into the light sockets.
Motor
Housing
Screw
Light
Kit Ring
Light
Rim
Fig. 19 STEP 3 (Fig. 19) - Concept 2 fan ONLY (pre Nov
2008 Only)
a) Remove the screws attached to the light rim.
b) Remove the light kit ring from the light rim.
P.S . Adaptor ring not required for New
Concept 1 or New Concept 2 (Nov 2008)

Electrician Installation Manual
Concept Ceiling Fan
(Timber and Moulded Blades)
1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not
approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The
use of unapproved controllers will void your warranty.
2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If
only one blade is damaged you are still required to replace with a new set.
Attaching a Concept light kit - E14 light (2x40W)
Light
Kit Ring
Light
Rim
Adaptor
Ring
Fig. 20 STEP 4 (Fig. 20) - Concept 2 fan ONLY
a) Place the adaptor ring on the light rim.
b) Place the light kit ring on the adaptor ring.
Light
Rim
Screw
Adaptor
Ring
Fig. 21 STEP 5 (Fig. 21) - Concept 2 fan ONLY
Use screws to attach the light ring and adaptor
ring firmly to the light rim.
Fig. 22
STEP 6 (Fig. 22)
a) Once globes are installed, the glass cover can
be fitted on to the fan.
b) Gently push the glass cover upwards and turn
it. The tabs should lock in to place ensuring the
glass cover is securely attached to the motor
housing.
Tab
Slots
Glass Cover

Electrician Installation Manual
Concept Ceiling Fan
(Timber and Moulded Blades)
1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not
approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The
use of unapproved controllers will void your warranty.
2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If
only one blade is damaged you are still required to replace with a new set.
Attaching a Concept light kit - GX53M 14W compact fluorescent light
Fig. 24
Tab
Slots
Light Wires
Light
Assembly Kit
Light
Motor
Housing
Tab
Slots
Tabs
Base Plate
STEP 1 (Fig. 23)
Push the base plate upwards and turn until the
tabs unlock to remove it.
Fig. 23
STEP 2 (Fig. 24)
a) Use the connectors to attach the light wires from
the motor housing to the light wires on the light as-
sembly.
b) Secure the light assembly kit using the 3 screws
provided.
Screw
Light
Kit Ring
Light
Rim
Fig. 25 STEP 3 (Fig. 25) - Concept 2 fan ONLY (pre Nov
2008 Only)
a) Remove the screws attached to the light rim.
b) Remove the light kit ring from the light rim.
P.S . Adaptor ring not required for New
Concept 1 or New Concept 2 (Nov 2008)

Electrician Installation Manual
Concept Ceiling Fan
(Timber and Moulded Blades)
1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not
approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The
use of unapproved controllers will void your warranty.
2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If
only one blade is damaged you are still required to replace with a new set.
Attaching a Concept light kit - GX53M 14W compact fluorescent light
Light
Light
Socket
STEP 6 (Fig. 28)
Fit the compact fluorescent light to the
light socket and rotate to secure in place.
Fig. 28
Fig. 29
Light
Glass Cover
STEP 7 (Fig. 29)
Gently push the glass cover upwards and turn it.
The tabs should lock in to place ensuring the
glass cover is securely attached to the motor
housing.
Light
Kit Ring
Light
Rim
Adaptor
Ring
Fig. 26 STEP 4 (Fig. 26) - Concept 2 fan ONLY
a) Place the adaptor ring on the light rim.
b) Place the light kit ring on the adaptor ring.
Light
Rim
Screw
Adaptor
Ring
Fig. 27 STEP 5 (Fig. 27) - Concept 2 fan ONLY
Use screws to attach the light ring and adaptor
ring firmly to the light rim.

Electrician Installation Manual
Concept Ceiling Fan
(Timber and Moulded Blades)
1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not
approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The
use of unapproved controllers will void your warranty.
2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If
only one blade is damaged you are still required to replace with a new set.
Attaching an extension rod - Hunter Pacific rods to be used ONLY
Step 1 (Fig. 30)
Loosen the down rod screws then unscrew
and remove the down rod pin screw to re-
move the standard down rod from the motor
housing.
Step 2 (Fig. 31)
Loosen the ball joint screw, take out the ball joint
pin and remove the ball joint. Then slide off the
canopy cover and canopy screw cover (concept
2 only)
Step 3 (Fig. 32 & 33)
Now install the extension rod and
reverse step 1 & 2 to secure the rod to
the fan and the ball joint.
NOTE: If the extension rod needs to be shortened, cut the rod to the required length and drill
the appropriate hole size to fit the ball joint pin. The cut end of the rod should be used on the
ball joint end only. When installing a 1.8m extension rod the wiring will need to be extended and
joined. This should be done using crimp style connectors.
Motor
Housing
Down Rod Pin Screw
Down Rod
Screw
Down Rod Canopy
Fig. 30
Fig. 32
Motor
Housing
Down Rod Pin Screw
Canopy Cover
Down Rod
Down Rod
Screw
Ball Joint Pin
Ball Joint
Loosen
Ball Joint
Screw
Down Rod Down Rod
Ball Joint
Fig. 31
Down Rod
Tighten Ball
Joint Screw
Ball Joint
Ball Joint Pin
Fig. 33

Electrician Installation Manual
Concept Ceiling Fan
(Timber and Moulded Blades)
1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not
approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The
use of unapproved controllers will void your warranty.
2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If
only one blade is damaged you are still required to replace with a new set.
Fan will not start
 Check that the reversing switch is pushed fully into its Summer or Winter position.
 Check wire connections in the wall switch and terminal blocks, ensure all wires
are making proper contact.
 If it is a Typhoon fan, check and ensure the reversing switch plate under the
switch cover is not bent, also check the 3 wires coming from the switch plate are
straight. Occasionally the switch plate may get bent during transportation, this
allows the switch cover to press against the plate and stop the fan from working.
 If it is a Typhoon fan, check the nine pin plug under the switch cover is properly
connected and the colours on the plug are corresponding.
 If it is a Concept fan and it has an external start up capacitor, check that this
external capacitor is properly connected.
Fan speed is not corresponding to the wall controller
 Check the speeds on the wall controller has been wired correctly and are making
proper contact. Brown = speed 1, Purple= speed 2, Red = speed 3.
 Check wires in the terminal block are connected properly, connection wires
should be stripped back at the connection point and unused wires should be
sealed and capped off.
 Check that the reversing switch is pushed into its Summer or Winter position.
Fan is not corresponding to the remote control
 Check for flat battery. Make sure the dipswitch settings in the hand piece and the
remote receiver for the same fan are corresponding.
Fan is wobbling
 Check the ball joint slot is locked into the hanger bracket groove.
 Make sure blades are a matching set; the letters on matching sets of blades
should be identical with the numbers varying within 3 grams of each other.
 Check blade screws are tightened firmly. If necessary use balancing kit provided
to settle the wobble.
Fan is noisy
 Check all screws and parts are secured firmly. Ensure there are no loose parts
moving inside the motor housing.
 Make sure the fan is installed with a Hunter Pacific wall controller only, do not use
solid state controllers as they can cause unpleasant motor noises.
National Warranty Line 1300 360 280
Monday to Friday from 9am to 5pm EST
Only available within Australia
Trouble Shooting Tips - Fan

Electrician Installation Manual
Concept Ceiling Fan
(Timber and Moulded Blades)
1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not
approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The
use of unapproved controllers will void your warranty.
2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If
only one blade is damaged you are still required to replace with a new set.
 Light will not turn on - Make sure globe has not blown and it is properly fitted
between the metal prongs. Check all light wires in the light kit, the terminal block
in the canopy cover and the wall switch has been connected together correctly.
 Light is not responding to remote control- Make sure globe has not blown
and it is properly fitted between the metal prongs. Check all light wires in the
light kit, the terminal block in the canopy cover and the wall switch has been
connected together correctly. Check dip switch settings in remote hand piece
and remote receiver correspond.
 Light wires appear to be missing or too short - Wires may be stuck in the
motor housing. Carefully pull wires out of the motor housing, careful not to strip
the wires as this may cause the fan to short.
 Light flickers or flashes - Check globe is secured between the metal prongs in
the light kit. Make sure you are using the globes specified.
Trouble Shooting Tips - Light
National Warranty Line 1300 360 280
Monday to Friday from 9am to 5pm EST
Only available within Australia

Electrician Installation Manual
Concept Ceiling Fan
(Timber and Moulded Blades)
1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not
approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The
use of unapproved controllers will void your warranty.
2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If
only one blade is damaged you are still required to replace with a new set.
Quick Checklist
1.
Ceiling fan is not installed to a solid-state wall controller. Neither leading nor
lagging edge controllers will give satisfactory performance. Wall controllers
must only be types approved for use by Hunter Pacific International.
2. The fan, optional fan light and bracket is earthed.
3. Fan and optional fan light are run from the same final circuit.
4.
Mounting bracket must be firmly secured to a solid structure such as a concrete
ceiling, steel structure or timber framing. If additional bracing is added it must
be firmly secured to the rafters and not left floating on the ceiling. Special
mounts, such as T-hooks, are available for certain types of installation.
5. Fan blades are at least 2.1m (7feet) above floor level.
6. Check the fan is operating correctly on all three speeds using the wall control-
ler.
7. If light is installed. Check light switch is functioning properly.
8. If remote control is installed. Check the fan (and light if installed) is responding
to the remote control correctly.
9. If remote control is installed. Check where possible a separate isolation switch
has been installed for the fan.
10. Check electrician’s details have been recorded onto the back page of the
Owner’s Operations and Warranty Manual.
Electricians make sure everything on this checklist is ticked off before you leave the installation site.
If you have trouble installing our product please refer to the trouble shooting section on the previous
page first then phone the Hunter Pacific Warranty Line on 1300 360 280 (open 9am to 5pm EST).
DO NOT uninstall the fan and DO NOT return fan to retailer.
Electrician Installation Manual
Concept Ceiling Fan
(Timber and Moulded Blades)
14 CONIM-V1.0