Hunter 9257-HUL-12VT User manual

9257-HUL-12VT Hunter 12V Trigger Kit
for Hunter Projection Screens & Lifts
(Please read the instructions before you use the devices)
www.hunterindia.in
User Manual

Install all components and then connect the wires according to the wiring diagram.(To be
installed by a professional)
Apply to the control of the direction and power off for alternator of pressure AC220V/110V/50-
60Hz, (It can be customized for other products also), such as electric screen, curtain, lifting rack, etc.
www.hunterindia.in
Product Brief
1.Perfect design and nice appearance
2.Robust & advanced circuit technology
2.Safe and reliable as hunter trigger adopts the high digital coding circuit with low rate of repeated code.
3.Complete set of remote with wall switch control
Applicability
Technical Parameter
1.Pressure: AC220V/110V±10% 2.Load Power: 500W
3.Remote Frequency: RF: 315/433MHZ IR:38KHZ
4.Remote Controlling Distance: RF:50M(open field) IR:8M±15
Installation
Edge Drop Time set & reset
Please use the remote control buttons when performing the memorising function.
Press the Down button, hunter electro-motor will go down.
When reaching the desired position, press the STOP and DOWN buttons at the same time.
Press the UP and Down buttons at the same time to clear the memory.
Warnings
1.If the contoller set does not work after installation, try to change the direction of the wire or
write to us [email protected].
2.Please change the battery(23A 12V) if the controlling distance is getting shorter or not
working.
Connect the wall switch with the power, and hear for 3 short beeping sound indicating no
acquired content in this remote controller. Then press any key in the remote control within
8 seconds, and a long consecutive beep will be heard. That means this remote controller has
acquired the related content and will start regular work in 8 seconds. (This is already pre-
configured at the facility for your ease & this part can be skipped)
To pair 2 remote controls into a wall switch, keep pressing the "STOP" key for 5 seconds.
when you hear 2 short beeps, press any key in the remote control, then a long consecutive
beep will be heard which means it has acquired the related content. In this way, the receiver
(Wall Switch) could be controlled by more than one remote controls.
Normally, you only need to press the keys in the receiver (Wall Switch) or remote control
according to the using method. When transferring the UP or Down status to DOWN or UP
one, press the related key twice (PAUSE for the first time). If there is no action for 5 minutes
or longer, the receiver will stop working and cut off automatically.
Keep pressing the STOP key for more than 15 seconds, 3 short beeps will be heard and the
existing pairing in the controller will be deleted.
Operation

Installation Schematic drawings
Wiring Schematic Drawing
UP
STOP
DOWN
UP
STOP
DOWN
Receiver Remote
www.hunterindia.in

www.hunterindia.in
Hunter 12V trigger is a reliable interface for Hunter projection screens and
projector lifts. It enables automatic lowering or raising of the motorised
screen when the projector is powered on or off. With no signal interference
Automatic lowering or raising of the projection
screen when the projector is turned on or off
Synchronized operation between projector and
screen, eliminating the need for manual
adjustments.
No signal interference with dedicated data channel
for reliable 12V trigger operation within the
projection system.
Seamless integration of projection screen control
with the projector, minimizing the need for an extra
remote control.
Ensure that the receiver is powered on and
ready for programming.
Press and hold the "Receiver Stop" key on the
receiver unit for 5 seconds.
After 5 seconds, release the "Receiver Stop"
key. The indicator light will flash 2 times, or the
buzzer will ring 2 times, indicating that the
receiver is in programming mode.
Immediately press the "USB Trigger Pairing
Button" on the USB device.
The receiver's indicator light will flash 1 time, or
the buzzer will ring 1 time, confirming that the
code has been successfully transmitted.
The USB trigger button is now programmed and
ready to use.
1.
2.
3.
4.
5.
6.
USB Device
Port
Pairing Button
Features
Pairing - USB 12V Trigger