Hunter 40351 User manual

LINE VOLTAGE THERMOSTAT MANUAL
Welcome to the Hunter Home Comfort family of quality products. The line voltage
thermostats are designed for operation with resistance heating elements and unit
heaters. These thermostats use snap action switches and do not require leveling.
There are two models: 40351–single pole and 40352–double pole.
Removal and Installation:
WARNING: HIGH VOLTAGE – RISK OF ELECTRICAL SHOCK. Before removing the
existing thermostat and installing your Hunter thermostat, disconnect the power to
the furnace to avoid an electrical hazard.
1) Before disconnecting your existing thermostat, make sure that you note and label
how the wires were connected to the thermostat. 2) Remove the existing thermostat.
3) Your Hunter thermostat is made up of three sections: the baseplate, the cover, and
the knob. 4) Connect the wires from the wall to the baseplate screw terminals
according to the connection diagrams for each model. Connect the ground wire to the
ground screw on the baseplate.
Caution: Failure to connect the ground wire could result in electrical shock. 5) Attach the
baseplate to the box with the two screws provided. 6) Snap the cover onto the baseplate
top first then the bottom. 7) Place the knob on the switch and turn to the off position.
8) Restore the power to the furnace. 9) Set the temperature by turning the knob to the
desired temperature.
Technical Assistance:
For technical assistance and support, call our customer service department at
901-745-9222 between 8 a.m. to 5 p.m. Central Standard Time, Monday through Friday.
Hunter Fan Company • 2500 Frisco Avenue • Memphis, TN 38114
®

ELECTRICAL SPECIFICATIONS
22 AMPS @ 125/277 VAC
3/4 HP @ 125 VAC 1.5 HP @ 250/277 VAC
OPERATIONAL SPECIFICATIONS
TEMP RANGE: 50° to 90°F
TEMP DIFFERENTIAL: 2°F
Limited Warranty
The Hunter Fan Company warrants your Hunter Thermostat to be free from defects in material and workmanship for a period of
one year from the date of sale to the original user or consumer purchaser. If your Hunter Thermostat malfunctions or fails within
the warranty period because of a defect in material or workmanship, we will replace it.
THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. THE DURATION OF ANY IMPLIED WARRANTY,
INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, MADE IN RESPECT TO YOUR HUNTER THERMOSTAT IS LIMITED TO THE PERIOD OF THE EXPRESS WARRANTY
SET FORTH ABOVE.
This warranty is voided if your Hunter Thermostat is not purchased and installed in the U.S.A.
This warranty excludes and does not cover defects, malfunctions, or failures of your Hunter Thermostat which were caused by
repairs by persons not authorized by us, mishandling, improper installation, modifications or damage to the Hunter Thermostat
while in your possession, or unreasonable use, including failure to provide reasonable and necessary maintenance.
Return your product, along with proof of purchase, to Hunter Fan Co. Service Department, 2500 Frisco Avenue, Memphis,
Tennessee 38114. You will be responsible for all insurance and freight or other transportation charges to our factory. We will
return your Hunter Thermostat freight prepaid. Your Hunter Thermostat should be properly packed to avoid damage in transit
since we will not be responsible for any such damage.
IN NO EVENT SHALL HUNTER FAN CO. BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT
APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
COM
NEUTRAL
HOT
NC
(POWER) 40351 – Single Pole
COMMON
COMMON
FURNACE
NEUTRAL
NC
NC
HOT (POWER)
40352 – Double Pole
40351 40352
FURNACE
FURNACE