HunterDouglas PowerView Parts list manual

Designer Roller & Designer Screen Shades
with PowerView®AC Automation for
Standard, Fascia, Pocket, & Coupled
Installation • Operation • Care

CONTENTS
Questions?
Call the Hunter Douglas Consumer Support Center at 1-888-501-8364.
© 2020 Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas or
their respective owners.
GETTING STARTED
Standard Shade .....................................................................1
Coupled Shade.......................................................................2
Fascia Shade..........................................................................3
Pocket Shade .........................................................................4
Tools and Fasteners Needed .................................................5
INSTALLATION
Installation Overview.............................................................6
STEP 1 — Install the Brackets ..............................................6
STEP 2 — Install the Shade................................................15
STEP 3 — Connect the Power Source ................................18
OPERATION
Testing the Shade................................................................18
Using the PowerView®Remote ..........................................19
Resetting Shade Programming............................................21
Adjust Shade Limits (If Necessary) .....................................21
Install the Fascia Panel........................................................22
Install Pocket Bottom Panel.................................................23
CARE
Troubleshooting ...................................................................23
Removing the Shade............................................................25
Cleaning Procedures............................................................26
DECLARATIONS........................................................... 27

PRODUCT VIEW
1
Standard Shade
Installation
Screws
Idle
Bracket
Bracket
Covers
(Optional)
Idler
Assembly
End
Cap
Bottom
Rail
Motor
Bracket
Bracket
Covers
(Optional)
Motor
Assembly

2
PRODUCT VIEW
Coupled Shade
Idler
Assembly
End
Cap
Bottom
Rail
Motor
Assembly
Bracket
Covers
Motor
Bracket
Idle
Bracket
Intermediate
Bracket
Bracket
Covers
Bracket
Covers

PRODUCT VIEW
3
Fascia Shade
Idler
Assembly
Fascia Clutch
Idle Bracket
Fascia
Fascia
Motor
Bracket
Motor
Assembly
End Cap
(Optional)
End Cap
Bottom Bar
End Cap
Tape

4
PRODUCT VIEW
Pocket Shade
Idle-Side
Installation
Bracket
Pocket
Bottom
Pocket
End Cap
Pocket
End Cap
Pocket
Idler
Assembly
End
Cap
Bottom
Rail
Motor
Assembly

GETTING STARTED
5
Thank you for purchasing Hunter Douglas Roller and Screen Shades with PowerView®
Automation. With proper installation, operation, and care, your new shades will provide years
of beauty and performance.
Please thoroughly review this instruction booklet and the enclosed packing list before
beginning the installation.
Tools and Fasteners Needed
■ Flat blade and Phillips screwdrivers
■ Level (laser level is recommended)
■ Measuring tape and pencil
■ Standard, Fascia and Coupled shades. Power drill, 1∕8" drill bit and a 5∕
16 " hex driver.
In addition, you will need fasteners designed to work with your specific mounting surface(s).
Standard, Coupled, and Fascia Shades
■ #10 x 1
1
⁄ 2 " Phillips Hex Head Screws (Provided). Two 1
1
⁄ 2 " screws are provided per
installation bracket.
Pocket Shades
■ #10 Hex Head Screws (Not Provided). See “Pocket Installation” on page 15.

INSTALLATION
6
Installation Overview
To install your shade, you will need to perform the following three steps:
STEP 1: Install the brackets and attach additional components
STEP 2: Install the shade
STEP 3: Connect the power source
STEP 1 — Install the Brackets
Mounting Types and Window Terminology
If the installation brackets are mounted correctly, the rest of the installation process follows
easily. To prepare for this important first step, review the mounting types and basic window
terminology illustrated below.
■ Refer to the appropriate page below based on the mounting type chosen for your order:
➤ Standard Shades
Inside Mount — page 7
Outside Mount — page 8
➤ Coupled Shades
Inside Mount — page 14
Outside Mount — page 11
➤ Fascia Shades — page 12
➤ Pocket Shades — page 14
Outside Mount
Shade mounts outside
window opening.
Inside Mount
Shade fits within
window opening.
Collectively, the sill and
jambs are called the
“window casement.”
Molding
Head Jamb
Sill
Jamb Jamb

INSTALLATION
7
Inside/End Mount — Standard Shades
■ If you ordered bracket covers. Mark
1
⁄ 8 " in from each window jamb for the outside
edge of each bracket.
■ Shades without bracket covers. Mark
1
⁄ 16 " in from each window jamb for the outside
edge of each bracket.
➤ The minimum depth required for mounting is 2
3
⁄ 4 ". For fully recessed mounting, the
depth is 3
1
⁄ 4 ".
IMPORTANT: The front edges of the installation brackets must be level and aligned to
eachother.
■ Place the outside edge of the brackets on the previously made marks, then mark each of
the screw holes.
■ Drill the screw holes using a
1
⁄ 8 " drill bit.
WARNING: Product is heavy. Mount into wood/metal studs or into concrete
with concrete anchors. Drywall anchors are not recommended.
■ Use a level to check that the mounting surface is level. Shim the brackets if necessary.
■ Attach the installation brackets using the screws provided.
➤ End Mount Shims (Optional). To ensure light gap is even on both sides, you may
need to shim the bracket. Do not tighten the screws fully. Orient the shim as shown.
Slide the shim in between the bracket and window casement. Tighten the screws
fully.
Proceed to “STEP 2 — Install the Shade” on page 15.
Inside Mount End Mount Shim
(Optional)

INSTALLATION
8
Outside Mount — Standard Shades
■ Determine the bracket locations.
➤ Center the ordered width over the window at the desired height and mark its location.
■ Place the outside edge of each bracket
1
⁄ 16 " in from the previously made marks, then mark
each of the screw holes.
➤ A minimum 3" flat vertical surface is required to mount the brackets.
➤ The top of the installation brackets should be at the desired height of the shade.
■ Drill the screw holes using a
1
⁄ 8 " drill bit.
■ Use a level to check that the mounting surface is level. Shim the brackets if necessary.
■ Attach the installation brackets using the screws provided.
WARNING: Product is heavy. Mount into wood/metal
studs or into concrete with concrete anchors. Drywall
anchors are not recommended.
Proceed to “STEP 2 — Install the Shade” on page 15.
Left
Bracket
Right
Bracket
Window Opening