HUROM M100 Series User manual

※ 발주용 인쇄시 본 페이지(시방서) 삭제 후 진행
시방서
DESIGN SPECIFICATION
R&D2본부 디자인팀 자재명(자재번호 / 파일명 / 버전) : 작성일 :
❶ 사이즈
❷ 인쇄도수
❸ 지류
❹ 페이지
❺ 제본
❻ 후가공
1. 자재 사양
2. 기재 언어
3. 제작 및 수정일자
4. 수정사항
※ 발주용 인쇄 시 필히 본 페이지(시방서) 삭제 후 진행하세요. 본 파일은 시방과 인쇄파일을 포함합니다. 유관의 부서와 업체의 견적 / 사양 / 발주 인쇄 진행 / 품질검사 외에는 사용을 금합니다.
인쇄물 시방서 개정 : 19' 11
전주경 4DZ040011 사용설명서 통합 M100 Series 유럽.미국권역_V.03 2022. 03. 03
150 x 220 mm
표지- 1도 인쇄
내지- 1도 인쇄
M 메트지 100g
120페이지
무선제본
없음
영문, 독일어, 프랑스어, 스페인어,
이태리어, 러시아어, 폴란드어
1. 2022.02.11_V.01
2. 2022.03.02_V.02
3. 2022.03.03_V.03
1. 해당없음
2-1. 12p.28p.46p.62p.78p.94p.110p - '블렌더 사용방법 가이드 페이지 번호' 수정
2-2. 20p 목차'6. Bedienungsanleitung des Entsafters' 문구 수정
3. 38p 목차 '3. Comment assembler l'extracteur de jus' 문구 수정

TM
English Deutsch Français Español Italiano Русский Polski

02
P.03-P.19 English
Instruction Manual | M100 Series
[ Home use only / Warranty not included ]
P.102-P.117 Polski
Instrukcja użytkowania | Seria M100
[ Tylko do użytku domowego / Gwarancja nie jest wliczona w cenę ]
P.20-P.35 Deutsch
Bedienungsanleitung | Serie M100
[ Nur für den privaten Gebrauch / Garantiekarte nicht eingeschlossen ]
P.36-P.53 Français
Mode d'emploi | SérieM100
[ Utilisation domestique uniquement / Garantie non incluse ]
P.54-P.69 Español
Manual de instrucciones | Serie M100
[Solo para uso doméstico/Garantía no incluida]
P.70-P.85 Italiano
Manuale di istruzioni | Serie M100
[ Solo per uso domestico / Garanzia non inclusa ]
P.86-P.101 Русский
Руководство пользователя | M100 Series
[Только для домашнего использования. Гарантия не включена]

03
IMPORTANT SAFEGUARDS
WHEN USING ELECTRICAL APPLIANCES, BASIC SAFETY PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED INCLUDING THE FOLLOWING:
WHEN USING ELECTRICAL APPLIANCES, BASIC SAFETY PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED. READ ALL INSTRUCTIONS.
TO PROTECT AGAINST RISK OF ELECTRICAL SHOCK, DO NOT PUT THE MAIN
BODY (MOTOR) IN WATER OR ANY OTHER LIQUID.
THIS APPLIANCE IS NOT INTENDED FOR USE BY PERSONS (INCLUDING
CHILDREN) WITH REDUCED PHYSICAL, SENSORY, OR MENTAL CAPABILITIES, OR
LACK OF EXPERIENCE AND KNOWLEDGE, UNLESS THEY ARE CLOSELY
SUPERVISED AND INSTRUCTED CONCERNING USE OF THE APPLIANCE BY A
PERSON RESPONSIBLE FOR THEIR SAFETY. CLOSE SUPERVISION IS NECESSARY
WHEN ANY APPLIANCE IS USED BY OR NEAR CHILDREN. CHILDREN SHOULD BE
SUPERVISED TO ENSURE THAT THEY DO NOT PLAY WITH THE APPLIANCE.
TURN THE APPLIANCE OFF, THEN UNPLUG FROM THE OUTLET WHEN NOT IN
USE, BEFORE ASSEMBLING OR DISASSEMBLING PARTS AND BEFORE
CLEANING. TO UNPLUG, GRASP THE PLUG AND PULL FROM THE OUTLET.
NEVER PULL FROM THE POWER CORD.
AVOID CONTACTING MOVING PARTS. DO NOT ATTEMPT TO DEFEAT ANY SAFETY
INTERLOCK MECHANISMS.
DO NOT OPERATE ANY APPLIANCE WITH A DAMAGED CORD OR PLUG, OR AFTER
THE APPLIANCE MALFUNCTIONS, OR IS DROPPED OR DAMAGED IN ANY
MANNER. RETURN APPLIANCE TO THE NEAREST AUTHORIZED SERVICE
FACILITY FOR EXAMINATION, REPAIR OR ELECTRICAL OR MECHANICAL
ADJUSTMENT.
THE USE OF ATTACHMENTS NOT RECOMMENDED OR SOLD BY THE
MANUFACTURER MAY CAUSE FIRE, ELECTRIC SHOCK OR INJURY.
DO NOT LET CORD HANG OVER EDGE OF TABLE OR COUNTER.
ALWAYS MAKE SURE HOPPER IS SECURELY FASTENED IN PLACE BEFORE
MOTOR IS TURNED ON. DO NOT UNFASTEN HOPPER WHILE JUICER IS IN
OPERATION.
BE SURE TO TURN SWITCH TO OFF POSITION AFTER EACH USE OF YOUR JUICER.
MAKE SURE THE MOTOR STOPS COMPLETELY BEFORE DISASSEMBLING.
DO NOT PUT YOUR FINGERS OR OTHER OBJECTS INTO THE JUICER WHILE IT IS
IN OPERATION. IF FOOD BECOMES LODGED IN OPENING, USE FOOD PUSHER OR
ANOTHER PIECE OF FRUIT OR VEGETABLE TO PUSH IT DOWN. WHEN THIS
METHOD IS NOT POSSIBLE, TURN THE MOTOR OFF AND DISASSEMBLE JUICER
TO REMOVE THE REMAINING FOOD.
DO NOT USE OUTDOORS.
DO NOT PLACE ON OR NEAR A HOT GAS OR ELECTRIC BURNER OR IN AHEATED
OVEN.
DO NOT USE APPLIANCE FOR OTHER THAN INTENDED USE.
SAVE THESE INSTRUCTIONS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.

0404
1. Precautions for Safe Use
1. Read 'Precautions for Safe Use ' (p. 4~5) and use
the appliance properly.
2. After reading the manual, keep it in a convenient
location for future reference.
3. Do not use it abroad which has different power
supply and voltage.
4. Any quality improvements is subject to change
without notice.
Before Reading Manual
Instruction Manual [ Home use only / Warranty not included ] | M100 Series
CONTENTS
P.04
P.05
P.06
P.08
P.09
P.10
P.12
P.14
P.15
P.16
P.17
P.18
P.19
1. Precautions for Safe Use
2. Precautions During Use
3. How to Assemble Juicer
4. How to Assemble Blender
5. Power Switch and Jog Dial Guide
6. How to Use Juicer
7. How to Use Blender
8. Food Ingredient Usage Guide for Juicer
9. Food Ingredient Usage Guide for Blender
10. How to Clean Juicer
11. How to Clean Blender
12. Before Requesting for Repair
13. Error code
This symbol indicates a potentially dangerous situ-
ation and control. Please read the details carefully
and follow the instructions to avoid dangerous situ-
ations. A violation of any of the warning marks may
cause a serious injury or death, or considerable
damage to the product.
• Do not use any current other than that specified on the
warranty card and product specifications. It may cause
electric shock, fire and/or performance impairment.
Connecting to a different voltage may reduce the motor's
lifespan or lead to a malfunction. For safety, ground the
power outlet at all times. Also, do not ground it to a gas pipe,
plastic water pipe, or telephone line.
• If the sheath of the power cord is peeled off or severed dur-
ing use of the product due to negligence, it may cause fire
and/or electric shock. Thus, please frequently check the
condition of the power cord, power plug and power outlet.
When the power cord is damaged, do not repair or remodel
modify it yourself and, instead, visit an after-sales service
center or branch store. Securely insert the power cord all
the way into an outlet.
• Do not bend, tie, damage or pull the power cord by force,
or place it near a high temperature or heat such as a gas
stove. Also, do not place any heavy object on top of the
product, wedge it into a narrow space, or alter it. It may
damage the power cord and cause fire and/or electric shock.
• Do not press buttons and insert or pull the cord with wet
hands. It may cause electric shock, a short circuit and/
or fire. Do not let any foreign substances get oncome into
contact and/or near the switch.
• Do not use the product in a place with a high humidity level
or risks of fire. Do not place the device on top of or near a
hot gas stove, microwave or any kitchen appliance.
• Do not attempt to modify it under any circumstances. Also,
do not attempt to dismantle or repair it yourself. Do not
insert any foreign objects such as a finger, chopstick, spoon,
fork or iron pin into any crack or hole in the product.
• When the power plug is damaged, do not repair or attempt
to modify it yourself and, instead, contact the HUROM Cus-
tomer Service Center for an inspection.
• Do not moisten or splash water on the product body. If
water or foreign matter gets into the product body, pull
out the power plug and then contact the HUROM Customer
Service Center.
• Do not soak the product body in water to clean it. Do not let
water get on the power plug. Do not wipe the product with
a paint thinner, benzene or spray-type chemical. Please
store the product away from a place of high temperature
and humidity.
• Do not install and use the product in a place such as a sink
and bathtub where water may get into it. Do not control
buttons with wet hands. Use the product only on a flat and
dry floor. Make sure that no water or foreign material con-
tacts the product's power switch.
• Do not use several electric alliances simultaneously by
plugging them all into a single multi-tab power strip or
outlet. Please use an exclusive outlet.
• Do not move the product during operation. and do not in-
sert hands, tools or anything other than ingredients and
the pusher into the container. Insertion of hands, tools, etc.
may cause a serious injury, accident and/or malfunction.
• Those who are not familiar with the handling of this prod-
uct should not use it alone. Those who experience physical
and/or mental discomfort, those who lack experience and
knowledge, and children should use the product with a
guardian.
• Do not use it within children's reach. Children should be
carefully supervised so that they do not use this device for
play. There is a risk of an injury or malfunction if children ac-
cidentally hit and knock it down.
• For children, even a minor burn may be extremely
dangerous. Educate children so that they learn the habit of
practicing caution about hot liquids.
• Turn off the power and pull out the power plug when in-
stalling or detaching an accessory, when the product is not
used, or before cleaning. Make sure to pull out the power
cord before cleaning or when it is not in use. Also, when pull-
ing the power cord, make sure to grab the plug to pull it.
• Make sure to remove the power plug from the outlet
before cleaning the product. Do not clean the product in an
incorrect method. Do not clean it by a method not specified
in the user manual. Make sure to refer to the user manual
for cleaning.
• Use it in place with a level surface. Do not use the product
outdoors, or exert any excessive shock to or drop the
product. Do not use the product while it is damaged.
• Do not use the product while wearing or possessing an
article with magnetic forces (e.g. magnetic bracelet).
Keeping an item with magnetic forces near the product
may cause a malfunction.
• The smell experienced when using a new product will
naturally go away over time. It is a common phenomenon
and has no issue during use.
• Use of an excessively large amount of ingredients may
damage the parts.
• Please remove all packaging and labels before use. All
protective materials attached to the container should be
removed before use.
• For safety, please keep packaging materials (plastic bags,
buffer materials, etc.) out of children’s reach.
• Prior to use, check if it is bound (assembled) at the correct
location.

05
English
• Do not use this household-use product for commercial
purposes. Use of the device for an incorrect purpose or
method or a failure to comply with the above guideline may
cause a serious injury or death, or considerable damage
to the product.
• Do not clean the product at a temperature of 80°C or
higher. Do not place it in a dishwasher, dryer, microwave,
etc.
• If the product is not cleaned immediately after use, the
pulp may dry up, which makes it difficult to disassemble
and clean it and also cause performance impairment. So,
if possible, clean it immediately after use. Do not use the
blender as a storing container. Please empty the container
after use.
• Make sure to thoroughly understand how to prepare
ingredients and prepare them properly before inserting
them.
• Do not conduct any idle run of the product before inserting
any ingredients.
• When using the product, be careful so that a tie, long
necklace, scarf, etc. do not get into the inlet.
• Do not use the device if a rotating body (screw, cutting
blades, stainless blades of the blender) or a cover (hopper
cover, blender cover) is damaged or cracked. If the device
is damaged, do not use it and contact the HUROM Customer
Service Center for an inspection or repair.
2. Precautions During Use
When Using Juicer
• Do not use it for more than 30 minutes continuously. It may
overheat the motor to and cause a malfunction. However,
when using it continuously, pause the operation and use it
after a break of over 5 minutes.
• Poorly prepared ingredients may hinder the extraction
process and/or cause damage to the product.
• Do not use this juicer for grinding grains.
• Ingredients in need of extra care when using the juicer
and ingredients unable to be juiced, Ingredients in need
of extra care
- When using soft ingredients alone such as bananas, aloe,
cactus, yams, ripened kiwi and tomatoes, the juice may
stagnate inside the chamber, which can make juicing diffi-
cult. Please add other ingredients that are not too soft.
- When inserting walnuts, peanuts, almonds, sunflower
seeds, pine nuts, beans, etc., add only a small amount or
add them with other ingredients after soaking them in
water.
Ingredients unable to be juiced
- Do not insert ingredients that cannot be juiced such as
sesame seeds, coffee beans, Chinese peppers, tree bark
and pine needles. Do not insert mudfish, eels, shrimp,
marsh snails, squid, etc.
- Do not insert fruits soaked in alcohol, honey or sugar
(grapes, raspberries, mulberries, etc.) and enzymes (glass-
wort, rock pine enzymes, etc.).
- Do not insert ingredients whose attributes make them
difficult to be juiced such as silverberries, aloe, cactus,
quince, bananas, yams, kudzu root, sugar cane, acorns and
dandelions.
- Do not insert boiled ingredients such as boiled potatoes
and sweet potatoes. Do not use it for grinding grains.
- Do not use frozen ingredients for extraction.
• It is recommended that you consume extracted vegetable
juice immediately, if possible, and do not store it for a long
period of time.
• While the product is in operation, do not lift the container
or open the cover. Do not conduct any idle run of the
product. It may shorten the product’s lifespan.
• Do not re-extract juice from pulp that has already been
juiced.
• Do not insert ingredients into the hopper above the guided
limit mark.
• Do not insert a chopstick or spoon into the juice/pulp outlet
during operation.
• When inserting ingredients, do not use anything other
than the pusher. It may damage the parts or cause a bodily
injury and/or malfunction.
• Juice or pulp may overflow. The juice can flow backwards
into the hopper if the juice cap is closed while juicing.
• When juicing frozen fruits or ingredients that have freezer
burn as they have been stored in the freezer for too long,
the amount of extraction is small or it may be impossible
to extract at all.
When Using Blender
• Do not use it continuously for a duration longer than the
standard usage time. It may overheat the motor and
cause a malfunction. If it has to be used for longer than
the standard usage time, do so with a gap of 30 minutes
or longer. In Manual Mode, use it for 1 minute, 8 times ((1
minute of operation followed by 1 minute of stoppage,
prohibited to use 9 consecutive times) and, in Auto Mode,
use it once for 7.5 minutes (7.5 minutes of operation
followed by 30 minutes of stoppage, prohibited to use 2
consecutive times).
• When detaching the container during operation, do so af-
ter the blades come to a complete stop. When removing
food or mixing ingredients, make sure to do so after separat-
ing the container from the product body.
• Operate the blender only when the cover is closed.
• When the power is on, do not remove the food stuck on
the walls of the blender container or mix the ingredients.
When removing food or mixing ingredients, make sure to do
so after separating the container from the product body. For
re-operation, stop the device completely before use.
• When inserting hands or kitchen tools in the container,
make sure to pull out the plug after the device stops
operating completely. When touching or cleaning the
blades, be careful not to touch the sharp edges. Be careful
not to cut your hands by the blades.
• Do not pour water of an amount greater than the maximum
allowable capacity specified on the recommended usage
diagram. The amount of water or food ingredients should
be maintained over the minimum (100ml) mark and
below the maximum (1,000ml) mark. Please use the
recommended amount. If water or food ingredients are
filled over the maximum limit, they may overflow.
• Do not touch sharp blades with bare hands. Use a cleaning
tool such as a cleaning brush to wash the product.
• When separating the product body and blender, wait until
the blades come to a complete stop. Do not separate the
blades and container. Blades cannot be detached from the
container. Please be mindful of your safety.
• This is a product that performs high-speed rotation
so it produces noise during rotation. It is a common
phenomenon and has no issue during use. If the device
produces excessive heat or smoke, stop using it
immediately and contact the HUROM Customer Service
Center.
• Use the pusher for cold ingredients only and, to prevent
overheating, donot usethe ManualMode for over1 minute.
Do not insert hot ingredients to cook. For hot ingredients,
cool them at room temperature before placing them in the
container.
• When making a smoothie, break the solid, frozen
ingredients into fine pieces before placing them in the
container.
• Processing extremely hard spices such as nutmeg or
ingredients like Phellinus linteus roots may damage the
blades.

06 3. How to Assemble Juicer
01
01 Match the protruded part at the top of the outer filter (⑤-1/⑥-1)withthechamber’sgroove(⑦-5) to
assemble.
02
02 Assemble the inner filter and screw on the outer filter, which is assembled on the chamber.
Assemble them so that the binding point of the inner filter (④-1) joins the protrusion at the top of the outer filter
(⑤-1/⑥-1).
03
03 Assemble the hopper cover (①-3) vertically onto the hopper (②-1).
04
04 Align the hopper [ ] assembly guide mark (⑦-1) with the chamber [ ] assembly guide mark (②-3)
toassemble them.
05
05 Turn the assembled hopper clockwise up to the chamber [ ] assembly guide mark.
If the internal parts are not assembled correctly, the hopper will not close.
06
06Check if the discharge cover (⑦-2) and the loop of the chamber are properly closed.
1. Lift the discharge cover to close it and fasten it with the loop.
2. If the packing is not correctly assembled or the lever is not properly closed, juice may leak or the lever may
open during extraction.
07
07 Place the correctly assembled chamber set onto the product body according to the chamber guide
mark (⑦-8) and the product body guide mark (⑨-2).
If the hopper is assembled on top of the product body, the hopper is not locked all the way due to the orange
"looseproof bump".
If the chamber is not settled according to the guide mark, turn it slightly left and right to settle it at the guide
mark.
⑤-1
⑤-1
/⑥-1
/⑥-1
⑦-5
⑦-5
①-3
①-3
②-1
②-1
01
01
③
③
④-1
④-1
02
02
03
03
⑦-2
⑦-2
06
06
04
04
②-3
②-3
05
05
①
①
⑦-1
⑦-1
07
07
⑦-8
⑦-8
⑨-2
⑨-2

07
English
3-1. How to Assemble Juicer: Assembly and Dis assembly of Silicone
* Packings are consumables that are recommended
to be replaced once every 6 to 12 months. They are
available for purchase through the Customer Service
Center.
(The juice may leak if the product is not assembled
properly.)
01
01 Hold and take out the packing as if you are pulling
it back.
02
02 After cleaning, insert one side of the packing first
as if you are hooking it.
03
03 Insert the remaining part and press down the
perimeter.
01
01 Hold and take out the packing as if you are pulling it
back.
02
02 After cleaning, insert the packing as shown in the
figure and then press it down.
Extraction Packing
SealPacking
01
01
02
02
⑦-3
⑦-3
⑦-3
⑦-3
01
01
02
02
⑦-4
⑦-4
⑦-4
⑦-4
Assemble the packing as shown in the figure.
Juice Cap Packing
Hopper Packing
01
01 Grab one side and pull it back to detach it.
02
02 After cleaning, check the top and bottom of the
packing and insert it as if you are hooking one side.
03
03 Firmly press the remaining part of the packing
without any folded area to assemble.
01
01
02
02
After cleaning, insert one side of the packing
first as if you are hooking it.
Insert the remaining part and press down the perimeter.
⑦-6
⑦-6
ChamberPacking
②-4
②-4
⑦-7
⑦-7

08 4. How to Assemble Blender
01
01 Fit the auxiliary cover (measuring cup) (⑧-1) on the container cover (⑧-3) and turn it
clockwise to lock it.
02
02 Put the desired ingredients into the container. Fit the container cover (⑧-2) into the container
(⑧) and close it.
03
03 Install the assembled blender container (⑧) on the product body (⑨).
If the power display lamp on the control and display panel is lit, the blender is ready for
operation.
All four surfaces of the blender container are assembled.
Before operating the product, check if the product body, container, cover and switch have all been
assembled in the correct positions. If the container is not correctly installed on the product body, the
blender will not work properly and the power display lamp will not be lit.
1LEDDisplay
2[ SMOOTHIE ] For smoothies
3[ ICE CRUSH ] For ice or frozen fruits
4[ SOUP ] For soup
5[GRIND ]Forgrinding
6[ CLEANING ] For cleaning
7Jog Dial / [START/STOP] button
8[MANUAL] Manual Mode display lamp
4
5
6
7
8
2
3
1
Blender Control Panel
01
01
02
02
03
03
⑧-1
⑧-1
⑧-3
⑧-3
⑧-2
⑧-2
⑧
⑧
⑧
⑧
⑨
⑨

09
English
5. Power Switch and Jog Dial Guide
Operate
- It works when the [START/STOP] button is briefly
pressed in the Standby Mode.
- It is used when activating the product for juicing.
- It is automatically terminated and switched to
the Standby Mode after 5 minutes elapse from
the start of the operation. If the chamber cover
is opened and then closed during operation for
additional insertion of ingredients, the timer is
reset.
* If the hopper cover is opened during operation,
the product stops. If the hopper cover is closed
again within 60 seconds, the operation continues.
But, if 60 seconds elapse, the operation
automatically stops and it switches to the Standby
(stop) state.
Stop
- This is used to stop the product's operation.
- The product stops when the [START/STOP]
button is briefly pressed in the operation state.
* If the chamber set is not installed, all lamps are
turned off.
* When 1 minute has elapsed from the Standby
(stop) state, the product enters the power saving
mode (light turned off). If the [START/STOP] button
is pressed or the chamber set is assembled, the
power saving mode is deactivated and it switches
to the Standby (stop) state.
Reverse Rotation
- This is used when the operation pauses or
a reverse rotation is needed due to excessive
insertion of ingredients during extraction.
*It works only when the [START/STOP] button is
pressed for over 1 second, and it stops when the
switch is released.
*If the screw stops during extraction, the product
automatically rotates in reverse but, if the power
is unstable, the reverse rotation may not work. In
such a case, press the [START/STOP] button for
over 1 second to activate a reverse rotation and
then press the [START/STOP] button again briefly
to activate.
Manual Mode 01
Turn the jog dial clockwise to operate the device at
a desired speed.
Once cooking finishes, return the jog dial to the [
Power Display Lamp ] position.
* The motor stops automatically after max. 1
minute of operation.
Manual Mode 02 (Pulse Mode)
While the [START/STOP] button is pressed, the
motor operates at the maximum speed. Once
the button is released, the operation stops and it
switches to the Standby (stop) state.
* The motor stops automatically after max. 1
minute of operation.
When you turn the jog dial in Auto Mode
the LED of the desired program mode is lit and,
once the [START/STOP] button is pressed, the
selected [Auto Mode] begins.
Once cooking finishes, the operation stops
automatically.
To stop the operation, return the jog dial to the
Power Display Lamp position or press the [START/
STOP] button, which cancels the operation and
switches to the Standby Mode.
< Juicer Standby Mode (container present) > < Blender Standby Mode (container present) >

10 6. How to Use Juicer
04
04
07
07
05
05
08
08
06
06
09
09
01
01
03
03
02
02
정회전
역회전
정지상태
작동스위치 정회전
역회전
off(정지) 정지
정회전
역회전
정지상태
작동스위치 정회전
역회전
off(정지) 정지

11
English
6. How to Use Juicer
01 Pull the lever on the inside of the hopper handle to open the hopper cover.
①The hopper cover opens when pulling the lever on the inside of the hopper handle. Insertion of an excessive
amount of ingredients may put too much strain on the product.
02 Add ingredients only up to the limit mark of the hopper.
①For soft ingredients, mix them with other ingredients for extraction.
② When extracting a large amount, frequently empty the chamber and pulp container.
03 Close the hopper cover and keep the juice cap open.
①Before turning the extraction dial, place the juice container first.
② The juice may flow backward into the hopper if the juice cap is closed during extraction.
If the juice does not come out even after opening the juice cap, open the hopper cover and empty the contents.
04 Press the [START/STOP] button to start operation.
① If the screw stops during operation, the product automatically rotates in reverse and then goes into a
normal operation. But, if the power is unstable, the reverse rotation may not work automatically. In such
a case, press the [START/STOP] button for over 1 second to activate a reverse rotation and then press the
[START/STOP] button again briefly to activate.
②A timer, which automatically stops after about 5 minutes from the start of operation, is set. If the [START/
STOP] button is controlled during operation or the hopper cover is opened and then closed, which pauses
and then restarts the machine, the timer is reset to 5 minutes again.
05 To add more ingredients during operation, use the additional inlet or open the hopper cover.
①When the hopper cover is opened, the operation stops.
②Do not use anything other than the designated pusher.
③ In case the screw spins but the ingredients fail to be ground in the hopper during extraction, use the
pusher to press the ingredients down.
06 Frequently empty out the pulp container and juice container so that they are not filled up.
07 Let the machine operate for about 1 more minute after all ingredients go down in the hopper.
① It slowly presses and squeezes the ingredients so it takes some time until the last ingredient is juiced.
②Removing the remaining pulp by additionally operating the machine after extraction makes it more
convenient to detach the hopper and clean the parts.
08 Once the juicing and pulp removal are finished, press the [START/STOP] button to stop the machine.
①The machine stops 3 seconds after it is stopped by the [START/STOP] button.
09 Pour any remaining juicebytiltingthechamber forward.
①For thickly concentrated juice made of tomatoes, etc., the juice may still remain in the chamber.
Note
The reverse rotation is a function that returns the ingredients upward. It only works while the [START/
STOP] button is pressed and, once you lift your finger from the button, the screw stops rotating. After
the screw is completely stopped after a reverse rotation, press the [START/STOP] button briefly to start
the operation again. When operating the extraction or reverse rotation function, make sure to press the
[START/STOP] button after the screw stops moving completely. If the machine does not work even after
following the above steps, pull out the power cord from the outlet, detach the chamber set, wash it and
use it again. Due to its characteristics, the motor will not stop at once but, instead, continue to spin slowly
in the direction of operation before coming to a complete stop.

12 7. How to Use Blender
7-1. Manual Mode
Manual Mode 01: [ Min / Max ] Speed control dial
01. Check if the container in which ingredients are inserted is installed on the product body and if the
cover is closed.
* If it is not prepared, please refer to How to Assemble Blender on Page 08.
02. Turn the jog dial clockwise to operate the device at the desired speed.
Once cooking finishes, return the jog dial to the [Power Display Lamp] position.
* The motor stops automatically after max. 1 minute of operation.
Manual Mode 02: Pulse Mode
01. Check if the container in which ingredients are inserted is installed on the product body and if the
cover is closed.
* If it is not prepared, please refer to How to Assemble Blender on Page 08.
02. While the [START/STOP] button is pressed, the motor operates at the maximum speed.
Once the button is released, the operation stops and it switches to the Standby (stop) state.
* The motor stops automatically after max. 1 minute of operation.
※Warning
Do not remove the container until the blades stop rotating completely and the speed control dial returns to the [
Power Display Lamp ] position.
Once the container is detached from the product body while the speed is being controlled, the Operation Display
Lamp on the body is turned off and the motor stops.
As soon as the container is re-installed on the product body, the Power Display Lamp on the body blinks.
For a normal operation again, return the speed control dial to the [ Power Display Lamp ] position.
Then, the machine will operate normally again.
01
01
01
01
02
02
02
02
⑧
⑧
⑨
⑨

13
English
7. How to Use Blender
Auto Mode: SMOOTHIE, ICE CRUSH, SOUP, GRIND, CLEANING
01. Check if the container in which ingredients are inserted is installed on the product body
and if the cover is closed.
* If it is not prepared, please refer to How to Assemble Blender on Page 08.
02. Turn the jog dial counterclockwise to select a desired Auto menu.
* You may choose from 5 Auto menus and please refer to the following table for each menu.
03. When pressing the [START/STOP] button, the selected [Auto Mode] begins.
Once cooking finishes, the operation stops automatically.
* To stop the operation, return the dial to the Power Display Lamp position or press the
[START/STOP] button, which cancels the operation and switches to the Standby Mode.
7-2. How to Use Auto Mode
Auto Program Purpose of Auto Program Recommended amount of
use
Program
operation time
[ SMOOTHIE ]
For smoothies
Soft and thickly concentrated
smoothie using vegetables, soft
fruits, nuts, etc.
Min. 100ml / Max. 1,000ml 55 sec.
[ ICE CRUSH ]
For ice or frozen
fruits
Sherbet and slushies using ice
and frozen fruits
Min. 100ml / Max. 500ml
(refer to the recipe) 50 sec.
[ SOUP ]
For soup Warm soup and latte Min. 100ml / Max. 500ml
(refer to the recipe) 7 min. 30 sec.
[ GRIND ]
For grinding
Quickly grind dry ingredients
(coffee beans, etc.) in extremely
fine pieces
Max. 200g 40 sec.
[ CLEANING ]
For cleaning
Self-cleaning mode helps easily
wash even the areas that are
difficult to be cleaned by hand
Min. 100ml / Max. 1,000ml 19 sec.
01
01
03
03
02
02

14
8-1. Basic lter (orange) 8-2. Fine lter (black)
• It is used when juicing fibrous ingredients or root,
stem and leaf vegetables (for common fruits and
vegetables, please use the basic filter).
• Filter classification: The filter classification mark
of [B] is displayed on the protrusion at the top of the
fitler.
Root vegetables
Carrots, beets, ginger,sweetpotatoes, potatoes,
garlic, etc.
Wash the ingredients in running water to remove dirt
and other foreign substances. For fibrous ingredients
such as ginger, peel the outer skin and cut them in
small pieces. For long ingredients, cut them vertically
for extraction.
Leaf and stem vegetables
Celery, kale, cabbage, water parsley, wheatgrass,
chives, etc.
Cut the ingredients into 3-cm or shorter pieces for
extraction. Since leaf and stem vegetables are rough
and fibrous, they are not easily juiced and can get
caught in the screw.
Common item: Ingredients unable tobe juiced
Inserting the following ingredients may cause
damageormalfunction.
- Ingredients that cannot be juiced such as sesame
seeds, coffee beans, Chinese peppers, tree bark and
pine needles (mudfish, eels, shrimp, marsh snails,
squid, etc.)
- Fruits soaked in alcohol, honey or sugar (grapes,
raspberries, mulberries, etc.) and enzymes
(glasswort, rock pine enzymes, etc.)
- Ingredients whose attributes make them difficult to
be juiced such as silverberries, aloe, cactus, quince,
bananas, yams, kudzu root, sugar cane, acorns and
dandelions
- Boiled ingredients such as boiled potatoes and sweet
potatoes
- Do not use it for grinding grains.
- Frozen ingredients
• Use it for juicing common fruits and vegetables.
• Filter classification: The filter classification mark of [A]
is displayed on the protrusion at the top of the filter.
Citrus fruits
Grapefruit,oranges, lemons,etc.
Prepare the ingredients by peeling and cutting them into
smaller pieces to fit in the hopper inlet.
Fruits with thick peels
Pineapples,dragon fruit, melons, watermelons,
pomegranate, etc.
Prepare the ingredients by peeling and cutting them into
smaller pieces to fit in the hopper inlet.
Seeded fruits
Grapes,apples,peaches,persimmons,plums,
cherries,pears,Koreanmelons,etc.
For ingredients containing hard, unchewable seeds or
large-sized seeds such as those in peaches, make sure to
remove the seeds first and cut and prepare only the flesh.
Hard seeds may stop the operation or damage the parts.
Apple seeds contain toxicity so remove them as much as
possible. For grapes, pluck each grape from the bunch
after cleaning them thoroughly. Do not extract only the
ingredients that are too soft; instead, mix them with other
fruits and vegetables.
Soft fruits
Singleextraction (berries,cherry tomatoes,
pineapples, etc.)
Thoroughly clean and cut the ingredients into small pieces
that can fit in the hopper inlet.
For fruits and vegetables with stalks, remove the stalks
first.
Mixed extraction (strawberries, kiwi, bananas,
tomatoes,mangoes,etc.)
For dry and viscous ingredients, mix them with other
ingredients for extraction.
Remove the peel and stalks. For mangoes, remove seeds.
J
* This is a reference on how to prepare each ingredient and, in case you have specific allergies, ingredients that suit your body must
be chosen.
* Refer to the ingredient preparation method and select a filter that suits the ingredients.
* Prepare ingredients in sizes able to be inserted into the hopper. If you want juicing of a large volume or fast juicing, cut the
ingredients into smaller pieces before inserting them. For about 1kg, repeat the "disassemble and clean after juicing" step for use.
* Do not insert ingredients into the hopper above the guided limit mark.
* When juicing ingredients other than root, leaf and stem vegetables with a fine filter, the ingredients may stagnate inside the
chamber.
* When juicing fibrous fruits and vegetables with a basic filter, the juice may thicken.
8. Food Ingredient Usage Guide for Juicer

15
English
Dry and hard ingredients
Grinding over 200g of dry ingredients (anchovies,
shrimp, mushrooms, etc.), coffee beans, rice, etc. may
put too much strain on the product. Dry grains or
seafood can be ground more easily if they are roasted
or stir-fried first.
Recommended amount of use: Less than 200g
Minced ingredients for seasoning
For garlic, onions, chili peppers, ginger, etc., grind them
at a low speed and then stop the operation before
gathering the ingredients again and re-grinding them
(to be repeated 2 to 3 times). Insertion of an excessive
amount of ingredients may put too much strain on the
product.
Recommended amount of use: Less than 300g
Ingredients unable to be used
Ingredients as hard as a rock, flour and other
ingredients for dough, meat with large bones or
many tendons, hot ingredients, hard fruit seeds, etc.
Highly viscous vegetables and fruits
Ingredients with high viscosity such as steamed or
boiled ingredients (sweet potatoes, autumn squash,
etc.), soaked or boiled grains (soaked rice, etc.),
avocadoes, mangoes and bananas are not mixed
thoroughly if there is not enough water. Such
ingredients will be ground well when inserting the
ingredients and water at a 1:1 ratio. If the water content
is low, blades may not move due to the viscosity of the
ingredients, which may cause a malfunction or reduce
the product’s lifespan.
Recommended amount of use: Less than 1000ml
Hard fruits and vegetables with low water
content such as
spinach, celery, carrots, apples, pears, radish, broccoli
and cabbage cannot be ground well as the upper and
lower sections are not mixed sufficiently. Such
ingredients will be ground well when inserting the
ingredients and water at a 1:1 ratio.
Recommended amount of use: Less than 1000ml
Frozen fruits and slushies
Frozen ingredients such as frozen mangoes, frozen
blueberries, frozen bananas and ice-added ingredients
are only ground in the lower section due to the absence
of water content. Such ingredients will be ground well
when inserting the ingredients and water at a 1:1 ratio.
Recommended amount of use: Less than 1000ml
* When grinding ice, the ground ice should be smaller than 20mm and lighter than 200g.
* Do not remove the container until the blades stop rotating completely and the jog dial returns to the stop
position.
* If blending is performed without the auxiliary cover, the contents may fly outside so make sure to use it
after properly installing the auxiliary cover.
* Do not insert any ingredients that are not edible into the container.
* When grinding grains or dried ingredients, the powder or ground materials may be spattered out of the
container.
(It is recommended to grind dried ingredients 7 or fewer consecutive times (1-minute operating
condition)).
* Manual Mode (jog dial control) enables to control the speed and, if it is operated too slowly, the motor may
stop due to the load of the ingredients, which may subsequently generate an error (Er-06). In case the error
occurs, switch to the Stop position to clear the error.
Raise the speed further attheinitial operation.
* When controlling the machine while the container has been removed from the product body, Empty
Container (
└┘
blinks) is displayed and the machine does not operate.
For normal operation, move the jog dial to the Stop position, place the container and operate it again.
9. Food Ingredient Usage Guide for Blender

16 10. How to Clean Juicer
After the product stops operating completely, pull out
the power cord with dry hands. Even after the product
is stopped, the motor will slowly come to a stop so,
after the operation stops completely, wait about 3
seconds before detaching the chamber set.
01 Detach the chamber set from the product body. Turn
the hopper to open it and then sequentially pull each of
the parts to disassemble them.
02 Wash the parts with a cleaning brush under running
water.
03 Open the discharge cover and juice cap to clean the
chamber.
04 Wipe the product body with a damp towel or soft
cloth.
05 Detach and wash silicone packings after use. -
Residues may still be stuck. (hopper packing, juice cap
packing, extraction packing, seal packing, chamber
packing)
06 You can sterilize the parts by soaking them in warm
water diluted with baking soda, citric acid or vinegar.
※Failure to clean the product immediately after use
may cause its stainless steel parts and other parts to
corrode or become discolored due to salt and pulp from
the ingredients. Also, contaminants may be dried up
and stuck inside, which makes it difficult to disassemble
and clean them and may also cause performance
impairment. Be sure to clean and air-dry it completely
immediately after use and store it in a clean place. For
long-term storage, use a cleaning brush to wash it. Do
not clean with boiling or high-temperature water or use
a cleansing sponge, steel sponge, abrasives and other
sharp cleaning tools. Do not place it in a dishwasher or
dish dryer.
※If clean water is poured and shaken for washing, the
pulp will come off more easily.

17
English
11. How to Clean Blender
How to use [CLEANING] Mode
01 Pour water into the container insomuch that the
blades are submerged.
02 Place the container on the product body and then
assemble the container cover and auxiliary cover
(measuring cup) correctly.
03 Turn the jog dial to select the [CLEANING] menu in
Auto Mode and then press the [START/STOP] button
to wash.
※Do not remove the container until the blades stop
rotating completely and the jog dial returns to the
stop position. Turn off the power, detach the plug
and then disassemble the container.
01 Pull out the power cord to turn off the power. Wipe
the product body with a damp towel or soft sponge.
Be careful not to soak the product body in water or let
water get into it.
02 Separate the container cover and auxiliary cover to
wash them.
Wash and dry them before assembling.
03 Gently rinse the inside of the container with water.
Be careful not to let water get into the bottom of the
container that touches the product body. Do not soak
the container in water. It may create rust or affect the
product’s performance.
※In case foreign matters fail to be removed from
the blades after washing, do not place your hand into
the container but, instead, use a cleaning tool such as
a cleaning brush to wash off the foreign matters.
※Blades cannot be detached from the container. Do
not detach them and watch out for safety.
※ Do not place any of the parts into a dishwasher.

18
Check the following before asking for repair. For follow-up service and any inquiry you may have while using
the product, please contact our Customer Center, or homepage at http://www.globalhurom.com Check the
manufacturer’s number or the number under the barcode when requesting for follow-up service or parts.
12. Before Requesting for Repair
Common
It does not operate only
with the product body.
Check if the chamber set of the juicer or the container of the blender and
the product body are properly assembled. Make sure to turn the power off
when assembling or disassembling the product.
Assemble it so that it is
aligned with the safety
sensor.
Check if it is assembled in accordance with the guide mark. Make sure to
turn the power off when assembling or disassembling the product.
There are cracks or
scratch marks on the
product.
In the process of making the molding, curve-shaped marks are created in
addition to the straight-lined mold marks. They are normal parts and do not
affect the operation at all.
It does not work.
Check if the power cord is properly inserted. The machine may not
work after a long period of use. It will operate normally after the heat of
the product body (motor) cools down. Check if the product is properly
assembled. If the product is assembled incorrectly, it will not work. Check
if the product is assembled according to the steps specified in the assembly
guide. Refer to the assembly guide page.
The juicer stops operating
during juicing.
Juice may leak through the pulp outlet immediately after inserting
ingredients. Have an excessive amount of ingredients or extremely thick
ingredients been inserted? Refer to Page 11 of the manual to activate a
reverse rotation. For safety, a timer, which automatically stops after about 5
minutes from the start of operation, is set. Press the [START/STOP] button
again briefly to start operation.
Juice leaks through the
pulp outlet immediately
after
the ingredients are
inserted.
Depending on the inserted ingredients, small amounts of juice may
leak through the pulp outlet. This is not a product defect but, rather, a
phenomenon caused by the characteristics of the ingredients. The leakage
will stop once the product starts running. If the leakage continues, contact
the Customer Service Center.
Juicer
Juice flows back into the
hopper.
Did you extract juice with the juice cap closed? When juicing with the juice
cap closed, the juice may flow backward into the hopper. If the contents are
not sufficiently discharged even after opening the juice cap again, open the
hopper cover and empty out the contents.
Juice leaks between the
hopper and the chamber,
or between the chamber
and the product body.
Is the hopper packing or chamber packing assembled correctly? The juice
will leak if the hopper packing or chamber packing has been assembled
upside-down or incompletely. Check if the packing is assembled properly.
The hopper does not open.
There may be excessive pulp remaining inside. Operate the product to
discharge the pulp inside or repeat the process of activating a reverse
rotation for about 10 seconds and then stopping 2 to 3 times. Then, the
hopper will open without any issue. Were any foreign substances or solid
matter (hard seeds such as persimmon seed) inserted? If any foreign
substances or solid matters are inserted, parts may be damaged more
seriously when attempting a reverse rotation so contact the Customer
Service Center and request after-sales service.
The chamber shakes
during juicing.
The product may wobble slightly due to the motions of the product body's
motor. Depending on the ingredients' characteristics (hard or tough),
motions are generated in various magnitudes. This is not a malfunction
but, rather, a normal phenomenon observed when the screw rotates.
Compared to soft ingredients with much water content, relatively harder
ingredients may seem to produce a greater vibration. (e.g., carrots,
potatoes, radishes, beets, kohlrabi, etc.)
The discharge cover is
closed but the pulp is
discharged.
Even if the lever is closed, pulp will be discharged naturally. Depending on
the ingredients used, there may be a difference in the amount and speed of
discharge.
An unusual noise is heard
while juicing.
It is a natural sound produced when ingredients are being crushed. If the
ingredients are hard or tough like apples, carrots, cabbage, celery, beets,
etc., the extraction noise may be louder than that heard when juicing softer
ingredients.

19
English
12. Before Requesting for Repair
13. Error Code (common for juicer and blender)
Code Root cause Actions to take
Er01 If an overcurrent flows through the
product, this error is generated to protect
the product.
Stop operating the product and restart it
after a few minutes.
If the same problem continues to occur,
please contact the HUROM After-sales
Service Center.
Er04 If a high voltage is applied to the product,
this error is generated to protect the
product.
Stop operating the product and restart it
after a few minutes.
If the same problem continues to occur,
please contact the HUROM After-sales
Service Center.
Er06
1. If the automatic reverse rotation is
operated often during the juicer operation,
this error may be generated to protect the
product. (This is an operation to protect
the chamber in case hard ingredients
or ingredients unable to be juiced are
inserted.)
2. This error may be generated if the motor
fails to perform the initial activation while
there are too many ingredients in the
blender container.
3. This error may be generated if the
overloading on the motor leads to activation
of the temperature protection device.
4. This error may be generated if the
sensor that detects the motor’s operation is
broken.
1. Stop operating the product, check and
remove the contents inside the juicer’s
chamber set, and then restart it.
2. Stop operating the product and reduce
the amount of contents inside the blender
container or raise the motor speed at the
initial operation.
3. If the motor stops due to overloading,
let it rest for about 30 minutes before
operating the machine again.
4. If the same problem continues to occur,
please contact the HUROM After-sales
Service Center.
└┘
This error may be generated if the jog dial
or the [START/STOP] button is controlled
while there is no juicer chamber set or
blender container on the product body.
Install the juicer or blender container on
the product body before use.
If the same problem continues to occur,
please contact the HUROM After-sales
Service Center.
The screw stopped during
operation but a reverse
rotation does not work
automatically.
If the power is unstable, the product may not perform a reverse rotation
automatically. Refer to Page 11 of the manual and activate a reverse
rotation.
Juicing is automatically
terminated before the
5-minute timer ends.
It is a function that automatically shuts down to protect the product in case
the automatic reverse rotation is operated often during juicing. This may
occur if it is impossible to extract or if uncut ingredients are added.
Please refer to Page 14 of the manual for the instructions on each
ingredient and insert the ingredients accordingly.
Blender
The motor stops while the
blender is in operation.
If the blender is overloaded, the motor may stop. Turn off the power and
remove the ingredients that cause the overloading or let it rest for about 30
minutes.
Blender’s grinding
operation does not work.
The machine may stop operating if there are too many ingredients or the
ingredients are too thick.
Adjust the amount and size of the ingredients and then operate the machine
again.
In case dry ingredients are used in a large volume, add more liquid before
operation.