Husqvarna Viking Epic 3 User manual

100x150 100x150
FREE ARM EMBROIDERY HOOP
150x100mm
User Instructions
The Free Arm Embroidery Hoop is preferrable to
use for many different occasions. You can easily
embroider difficult-to-hoop projects without
opening a seam. Simply slide part of your
project around the free-arm when attaching the
optional Free-Arm Embroidery Hoop. You can
use the hoop on any type of garments or other
projects, as long as it is possible to slide the
hooped part on to the free arm of the machine.
Outer Hoop Inner HoopFree Arm Embroidery Hoop
Quick Release Retaining Screw
The embroidery surface measures 150x100mm. In the machine user
interface the embroidery area is shown with the (imagined) quick
release in the lower right corner. Consider that when positioning the
design.
• Open the quick release on the outer hoop, and loosen the retaining
screw. Remove the inner hoop.
• Place the project on a flat surface. Use suitable stabilizer at the
wrong side of the project. Place the outer hoop inside the project.
• Place the inner hoop on top of your project. The embroidery hoop
connector to the left of the inner hoop should be placed towards
the "closed" part of the project.
• Push the inner hoop firmly into the outer hoop.
• Close the quick release. Adjust the pressure of the outer hoop by
turning the retaining screw. The fabric should be taut in the hoop
for the best results.
• Remove the accessory tray from the machine and connect the
embroidery unit.
• Position your design as you wish in the embroidery area in the
machine user interface. Go to Embroidery Stitch-Out.
• Slide the hooped project around the free arm. It cannot be too
tight, the hoop must be able to move while embroidering. Hoop
your project so that the narrowest opening is placed around
the free arm, otherwise the opening could get caught when
embroidering and cause misplacement of the stitches.
• Arrange your project around the free arm and in the well area
of the embroidery unit. Make sure it is not too bulky under the
embroidery hoop connector. The hoop is designed for some fabric
to fit under the connector, but for larger projects it is preferrable if
parts of the fabric could be placed at the back of the machine.
USE THE FREE ARM EMBROIDERY HOOP
Embroidery Hoop Connector

TIPS & HINTS
Small Garments
• Turn the garment inside out. Fuse an iron on stabilizer to the
inside of the garment. Turn the garment right side out again. Trim
the stabilizer to fit the embroidery hoop, to avoid having excess
stabilizer inside the garment.
• Keep the quick release on the outer hoop closed, instead loosen
the retaining screw. Remove the inner hoop. Place the garment
on a flat surface. Place the outer hoop (with the quick release
closed inside the garment. If you want to embroider in the upper
part of the garment, place the quick release to the upper right.
• Place the inner hoop on top of the garment, the embroidery hoop
connector should be placed towards the bottom opening of the
garment.
• Push the inner hoop firmly into the outer hoop.
• Adjust the pressure of the outer hoop by turning the retaining
screw. The fabric should be taut in the hoop for the best results.
Difficult to Hoop Projects
Jeans/Trousers
• Fold up the trouser leg, place the lower part of the leg around the
free arm. Hoop stabilizer and attach the hoop. Place the trousers
around the hoop. Pull the leg further on to the free arm. Position
the trousers correctly. Pin in place at a few places. After you have
chosen your design, use the scan hoop or projection to place your
design.
• When in stitch out, you can use the Exact Position functions for
perfect positioning of your design. Use the baste around hoop
function to baste the trousers in place.
Note: The trouser leg cannot be too tight, it must be possible for the
fabric to move when the hoop is moving.
Collars, Necklines and Sleeves
• Place the project around the free arm, hoop self adhesive
stabilizer. Place the hoop inside the project, attach the hoop.
Position the garment on the hoop and baste in place.
FR Un mode d’emploi en français peut se télécharger sur
www.husqvarnaviking.com. Rechercher “Free Arm Embroidery Hoop
150x100mm” sous le titre “Accessoires”.
DE Die Bedienungsanleitung auf Deutsch können Sie unter
www.husqvarnaviking.com herunterladen. Suche nach “Free Arm Embroi-
dery Hoop 150x100mm” unter der Überschrift “Zubehör”.
NL Nederlands gebruiksinstructies kunnen worden gedownload op
www.husqvarnaviking.com. Zoeken naar “Free Arm Embroidery Hoop
150x100mm” onder de kop “Accessoires“.
IT Le istruzioni d’uso in italiano sono disponibili per lo scarico da www.
husqvarnaviking.com. Cerca in “Free Arm Embroidery Hoop 150x100mm”
sotto il titolo “Accessori”.
ES Las instrucciones de uso en español están disponibles para su
descarga en www.husqvarnaviking.com. Buscar “Free Arm Embroidery
Hoop 150x100mm” en el apartado “Accesorios”.
471132726A · VIKING is a trademark of KSIN Luxembourg II, S.a.r.l. HUSQVARNA and the “H” Crown Device are trademarks of Husqvarna AB and are used under license. © 2023 KSIN Luxembourg II, S.a.r.l.
All rights reserved
SV Användarinstruktioner på svenska nns att hämta på
www.husqvarnaviking.com. Sök efter “Free Arm Embroidery Hoop
150x100mm” under rubriken “Tillbehör”.
DK En dansk brugervejledning kan downloades fra
www.husqvarnaviking.com. Søge etter “Free Arm Embroidery Hoop
150x100mm” under overskriften “Exstratillbehør”.
NO Norsk bruksanvisning er tilgjengelig for nedlasting fra
www.husqvarnaviking.com. Søke etter “Free Arm Embroidery Hoop
150x100mm” under overskriften “Exstratillbehør”.
FI Suomenkieliset käyttöohjeet ovat ladattavissa osoitteessa
www.husqvarnaviking.com. Etsiä “Free Arm Embroidery Hoop
150x100mm” otsikolla “Lisätarvikkeet”.
RU Инструкции по эксплуатации на русском языке можно загрузить
на веб-сайте www.husqvarnaviking.com. искать “Free Arm Embroidery
Hoop 150x100mm” под заголовком “Принадлежности”.