Husqvarna Viking Tribute 145C User manual

145TH ANNIVERSARY LIMITED EDITION SEWING MACHINE
User’s Guide

This household sewing machine is designed to comply with IEC/EN 60335-2-28 and UL1594.
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic safety precautions should always be followed, including
the following:
Read all instructions before using this household sewing machine. Keep the instructions at a suit-
able place close to the machine. Make sure to hand them over if the machine is given to a third
party.
DANGER – To reduce the risk of electric shock:
• A sewing machine should never be left unattended when plugged in. Always unplug this
sewing machine from the electric outlet immediately after using and before cleaning, removing
covers, lubricating or when making any other user servicing adjustments mentioned in the
instruction manual.
WARNING – To reduce the risk of burns, re, electric shock, or injury
to person:
• Do not allow to be used as a toy. Close attention is neccesary when this sewing machine is used
by or near children.
• Use this sewing machine only for its intended use as described in this manual. Use only
attachments recommended by the manufacturer as contained in this manual.
• Never operate this sewing machine if it has a damaged cord or plug, if it is not working
properly, if it has been dropped or damaged, or dropped into water. Return the sewing
machine to the nearest authorized dealer or service center for examination, repair, electrical or
mechanical adjustment.
• Never operate the sewing machine with any air openings blocked. Keep ventilation openings
of the sewing machine and foot control free from the accumulation of lint, dust, and loose
cloth.
• Keep ngers away from all moving parts. Special care is required around the sewing machine
needle.
• Always use the proper needle plate. The wrong plate can cause the needle to break.
• Do not use bent needles.
• Do not pull or push fabric while stitching. It may deect the needle causing it to break.
• Wear safety glasses.
• Switch the sewing machine off (“0”) when making any adjustment in the needle area, such as
threading needle, changing needle, threading bobbin, or changing presser foot, etc.
• Never drop or insert any object into any opening.
• Do not use outdoors.
• Do not operate where aerosol (spray) products are being used or where oxygen is being
administrated.
• To disconnect, turn all controls to the off (“0”) position, then remove plug from outlet.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

• The foot control is used to operate the machine. Avoid placing other objects on the foot control.
• Do not use the machine if it is wet.
• If the LED lamp is damaged or broken, it must be replaced by the manufacturer or it's service
agent or a similarly qualied person, in order to avoid a hazard.
• If the supply cord connected with the foot control is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualied person, in order to avoid a hazard.
• This sewing machine is provided with double insulation. Use only identical replacement parts.
See instructions for Servicing of Double-Insulated Appliances.
SAVE THESE INSTRUCTIONS
FOR EUROPE ONLY:
This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be
made by children without supervision.
The noise level under normal operating conditions is less than 75dB(A).
The machine must only be used with foot control of type FR2 manufactured by Shanghai Binao
Precision Mould Co., Ltd.
FOR OUTSIDE EUROPE:
This sewing machine is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the sewing machine by a person responsible for their
safety. Children should be supervised to ensure that they do not play with the sewing machine.
The noise level under normal operating conditions is less than 75dB(A).
The machine must only be used with foot control of type FR2 manufactured by Shanghai Binao
Precision Mould Co., Ltd..
SERVICING OF DOUBLE INSULATED PRODUCTS
In a double-insulated product, two systems of insulation are provided instead of grounding. No
ground means is provided on a double-insulated product, nor should a means for grounding be
added to the product. Servicing of a double-insulated product requires extreme care and knowl-
edge of the system and should be done only by qualied service personnel. Replacement parts for a
double-insulated product must be identical to those parts in the product. A double-insulated prod-
uct is marked with the words ‘DOUBLE INSULATION’ or ‘DOUBLE INSULATED’.

CONTENTS
Machine Overview..................................................................1
Included Accessories..............................................................2
Stitch Table – Utility Stitches................................................4
Stitch Overview.......................................................................6
Fonts .........................................................................................6
GETTING READY TO SEW 7
Unpacking ................................................................................7
Packing Away After Sewing...................................................7
Accessory Tray ........................................................................7
Using the Free Arm................................................................7
Connecting the Foot Control Cord......................................8
Connect the Power Cord
and Foot Control ....................................................................8
Lower the Feed Teeth.............................................................9
Presser Foot Pressure.............................................................9
Raise and Lower the Presser Foot .......................................9
Changing the Presser Foot ....................................................9
Changing the Needle............................................................10
Needles ...................................................................................10
Spool Pins and Spool Caps .................................................11
Threading the Upper Thread..............................................12
Needle Threader ...................................................................13
Cutting the Thread................................................................13
Threading for Twin Needle.................................................14
Winding the Bobbin With
the Machine Threaded .........................................................15
Winding the Bobbin Using
the Vertical Spool Pin...........................................................15
Winding the Bobbin Using
the Auxiliary Spool Pin ........................................................16
Inserting the Bobbin ............................................................16
Automatic Thread Tension..................................................16
Correct and Incorrect Thread Tension .............................17
Starting to Sew .....................................................................17
OPERATING YOUR SEWING MACHINE 18
Functions Panel.....................................................................18
Functions on the TouchScreen...........................................19
Sewing Mode, ........................................................................20
Selecting a stitch....................................................................21
Selecting a font .....................................................................21
Programming.........................................................................22
My Stitches Menu ...............................................................24
SET Menu ............................................................................25
SEWING 27
Exclusive SEWING ADVISOR™.....................................27
Seam........................................................................................28
Overcast..................................................................................28
Seam and Overcast ...............................................................29
Baste........................................................................................29
Blind Hem..............................................................................29
Hem ........................................................................................30
Sewing Buttonholes..............................................................31
Sewing on Buttons................................................................33
Sewing Zippers......................................................................34
Center Zipper ........................................................................34
Darning and Mending ..........................................................34
Bartack (Manual)...................................................................35
Automatic Tapering Stitches ..............................................35
Smocking Stitches .................................................................36
Pictogram Stitches ...............................................................37
Quilting...................................................................................38
Speciality Stitches..................................................................39
POP-UP MESSAGES 40
Pop-up messages...................................................................40
TAKING CARE OFYOUR MACHINE 43
Cleaning the Machine...........................................................43
Troubleshooting....................................................................44

OVERVIEW – 1
29
30
1
2
4
6
7
3
8
9
11
12
13
14
10
15
16
17
18
19
20
21
23
25
24
26
22
27
10
28
5
MACHINE OVERVIEW
1. Lid
2. Pre-tension thread guide
3. Thread tension disks
4. Thread take-up lever
5. Presser foot pressure dial
6. Thread tension for bobbin
winding
7. Function Panel
8. Thread cutter
9. Sensor One-Step Buttonhole
Foot socket
10. LED-lights
11. Needle threader
12. Presser foot
13. Stitch plate
14. Bobbin cover
15. Free arm
16. Drop feed teeth switch
17. Needle bar with needle clamp screw
18. Presser bar
19. Presser foot ankle
20. Stitch overview
21. Spool pin
22. Spool caps
23. Auxiliary spool pin
24. Thread cutter for bobbin thread
25. Bobbin spindle, Bobbin stop
26. Handwheel
27. TouchScreen
28. ON/OFF switch, connectors for
power cord and foot control
29. Handle
30. Presser foot lever

2 – OVERVIEW
INCLUDED ACCESSORIES
Presser Feet
Utility Foot A
Attached on the machine upon delivery. This foot is used mainly for straight stitching and zigzag stitching with
a stitch length longer than 1.0.
Utility Foot B
When sewing decorative stitches or short zigzag stitches and other utility stitches with less than 1.0 mm stitch
length, use this foot. The tunnel on the underside of the foot is designed to feed smoothly over the stitches.
Buttonhole Foot C
This foot is used for sewing buttonholes step by step. Use the guide lines on the toe of the foot to position
the garment edge. The two tunnels on the bottom of the foot ensures a smooth feed over the buttonhole
columns. The nger on the back of the foot holds cording for corded buttonhole.
Blind Hem Foot D
This foot is used for blind hem stitches. The inner edge of this foot guides the fabric. The right toe of the
foot is designed to ride along the hem edge.
Zipper Foot E
This foot can be snapped on either to the right or to the left of the needle, making it easy to sew close to both
sides of the zipper teeth. Move needle position to right or left to sew closer to zipper teeth or for covering
large cording.
Edging Foot J
This foot is used for overcasting and seam/overcasting. Stitches form over the pin which prevents puckering
at the edge of the fabric.
Sensor One-Step Buttonhole Foot
When connected to the machine, the buttonhole is sewn in a suitable length to the button size that has been
entered into the machine.
Glide Sole
If sewing on foam, vinyl, plastic, or leather, the material might stick to the foot and prevent the sewing
machine from feeding properly. When using any of the above materials, sew on a piece of scrap fabric, to
make sure the machine feeds smoothly. If not, fasten the self-adhesive glide soles to the underside of the
presser foot.

OVERVIEW – 3
1. Seam ripper
2. Brush
3. Screwdriver
4. Felt pad (2)
5. Bobbins (5)
6. Stylus
7. Spool cap, large
(attached on the machine at delivery)
8. Spool cap, medium
(attached on the machine at delivery)
9. Spool cap, small
Accessories not pictured
Threads
Hard cover
Foot control, cable, net cable
Warranty card
Needles
12
3
5
4
6
87 9

4 – OVERVIEW
STITCH TABLE – UTILITY STITCHES
Stitch Stitch No. Stitch Name Presser Foot Application
1Straight Stitch,
center needle
position
A/B For all types of sewing. Select 29 different needle positions.
2Stretch Stitch,
left needle position
A/B For seams in tricot and stretch fabric.
3Reinforced Straight
Stitch, center needle
position
A/B For seams which are subject to considerable strain. Triple and elastic for reinforced
seams. Use to reinforce and topstitch sportswear and working clothes. For topstitch,
increase the stitch length.
4Straight Stitch
with FIX
A/B Begins and ends with forward and reverse sewing.
5Zigzag A/B For appliqué work, lace edging, sewing on bands etc. Stitch width increases equally to
the left and right.
6Three-Step Zigzag A/B For mending, sewing on patches and elastics. Suitable for light and medium weight
fabric.
7Two-Step Zigzag A/B For joining two pieces of fabric with nished edges and for elastic shirring.
8Reinforced Zigzag B For joining fabric edge to edge or overlapping in leather. For decorative sewing.
9Baste Stitch A/B For joining two pieces of fabric with a long stitch length.
10 Straight Basting
Stitch
A Use together with the foot control to baste layers of the fabric together. Lower the
feed teeth. Sew a stitch, raise the presser foot and move the fabric. Lower the presser
foot and make the next stitch. Repeat until the basting is done.
11 Overcast Stitch JSeam and overcast in one step along the edge or trim later. For light stretch and non-
stretch fabrics.
12 Stretch Seam
Overcast Stitch
BSeam and overcast in one step along the edge or trim later. For medium and me-
dium/heavy stretch fabrics.
13 Double Overlock
Stitch
BSeam and overcast in one step along the edge or trim later. For heavy stretch and
heavy woven fabrics.
14 Overlock Stitch BSeam and overcast in one step along the edge or trim later. For medium stretch
fabrics.
15 Elastic/Casing
Stitch
B For overlapped seams in tricot. To sew casing over narrow elastic.
16 Elastic Stitch
or Smocking
A/B Sew over two rows of elastic thread for elastic shirring.
17 Flatlock Stitch B Decorative hems and overlapped seams, belts and bands. For medium/heavy stretch
fabrics.
18 Stretch Blind
Hem Stitch
D Blind hems in medium and heavy stretch fabrics.
19 Woven Blind Hem D Blind hems in medium and heavy woven fabrics.

OVERVIEW – 5
Stitch Stitch No. Stitch Name Presser Foot Application
20 Bridging Stitch A/B For joining two pieces of fabric with nished edges and for elastic shirring.
21 Darning Stitch
(side to side)
A For mending small tears.
22 Darning Stitch (for-
ward and backward)
A/B Darn and mend small holes in work clothes, jeans, tablecloths and more. Stitch over
the hole, press reverse for continuous darning and auto stop.
23 Bartack
(manual)
A/B Reinforce pockets, shirt openings, belt loops as well as at lower end of a zipper.
24 Belt Loop Stitch A For securing belt loops.
25 Bartack Buttonhole Sensor
One-Step
Buttonhole
Foot/C
Standard buttonhole for most fabric weights.
26 Round End
Buttonhole
Sensor
One-Step
Buttonhole
Foot/C
For blouses and children’s garments.
27 Medium Reinforced
Buttonhole
C For medium and heavy fabrics.
28 Heirloom
Buttonhole
Sensor
One-Step
Buttonhole
Foot/C
For “hand look” on ne and delicate fabrics.
Tip: For jeans buttonholes, increase length and width of the buttonhole. Use thicker thread.
29 Keyhole
Buttonhole
Sensor
One-Step
Buttonhole
Foot/C
For tailored jackets, coats, etc.
30 Heavy Duty
Buttonhole
Sensor
One-Step
Buttonhole
Foot/C
With reinforced bartacks.
31 Leather Straight
Stitch Buttonhole
A/B For leather and suede.
32 Eyelet B For belts, laces, etc.
33 Automatic Button
Sewing
No presser
foot
For sewing on buttons. Set the number of stitches on the TouchScreen.
34 Satin stitch, narrow BFor appliqués, sewing on laces and trims. For light and medium fabrics.
35 Satin stitch,
medium
BFor appliqués, sewing on laces and trims. For light and medium fabrics.
36 Satin stitch, wide BFor appliqués, sewing on laces and trims. For heavy fabrics.

6 – OVERVIEW
Brush Line
Block
Cyrillic and Hiragana
Russian and Japanese fonts. See the fonts on the
TouchScreen of your sewing machine.
FONTSSTITCH OVERVIEW

GETTING READY TO SEW – 7
UNPACKING
1. Place the machine on a sturdy, at surface, remove the packaging and lift off the cover.
2. Remove the packing material and the foot control.
3. The machine is delivered with an accessory bag, a power cord and a foot control cord.
4. Wipe the machine, particularly around the needle and stitch plate to remove any soil before sewing.
Note: Your sewing machine is adjusted to provide the best stitch result at normal room temperature. Extreme hot or cold temperatures can affect the
sewn result.
PACKING AWAY AFTER SEWING
1. Press the ON/OFF switch to OFF.
2. Unplug the cord from the wall socket and then from the machine.
3. Unplug the foot control cord from the machine. Wind the foot control cord and place it inside the space on the underside
of the foot control.
4. Check to ensure that all accessories are in the accessory box. Slide the box on to the machine, behind the free arm.
5. Place the foot control in the space above the free arm.
6. Put on the cover.
ACCESSORY TRAY
Store presser feet, bobbins, needles and other accessories in
the accessory tray so that they are easily accessible.
Keep the accessory tray on the machine to provide a larger,
at work surface.
USING THE FREE ARM
Slide the accessory box to the left when you wish to remove it
and use the free arm.
Use the free arm to facilitate sewing trouser legs and sleeve
hems.
To replace the accessory box, slide it onto the machine until it
ts in place.
GETTING READY TO SEW

1
2
1 23
8 – GETTING READY TO SEW
CONNECTING THE FOOT CONTROL CORD
Among the accessories you will nd the foot control cord and
the power cord. Connecting the foot control cord to the foot
control is only necessary the very rst time you are going to
use the machine.
1. Take out the foot control cord. Turn the foot control over.
Connect the cord to the socket inside the space of the foot
control. Push rmly to make sure it is properly connected.
2. Lay the cord in the slot on the underside of the foot
control.
CONNECT THE POWER CORD
AND FOOT CONTROL
On the underside of the machine you will nd information
about the power supply voltage (V) and the frequency (Hz).
Before plugging in the foot control, check to ensure that it is
of type “FR2” (see underside of foot control).
1. Connect the foot control cord to the front socket on the
bottom right side of the machine.
2. Connect the power cord to the rear socket on the bottom
right side of the machine.
3. Press the ON/OFF switch to ON to turn on power and
light.
For the USA and Canada
This sewing machine has a polarized plug (one blade wider
than the other). To reduce the risk of electric shock, this
plug is intended to t in a polarized outlet only one way. If
the plug does not t fully in the outlet, reverse the plug. If
it still does not t, contact a qualied electrician to install
the proper outlet. Do not modify the plug in any way.

A
GETTING READY TO SEW – 9
LOWER THE FEED TEETH
The feed teeth are lowered when you move the switch on the
front of the free arm to the right. Move the switch to the left
if you wish to raise the feed teeth. The feed teeth will raise
as you begin to sew. The feed teeth should be lowered when
sewing on buttons and for free motion sewing.
PRESSER FOOT PRESSURE
Normal presser foot pressure is around ve. The higher the
number the more pressure the foot puts on the fabric. Knit
and soft fabrics should be sewn at lower pressure.
The presser foot pressure is adjusted with the dial found under
the lid. When adjusting the pressure lower the presser foot
rst.
RAISE AND LOWER THE PRESSER FOOT
The presser foot is raised and lowered with the presser foot
lever (A). The presser foot must be lowered when sewing.
By raising the presser foot lever and then pressing it farther
upwards, the lift height of the presser foot is increased to an
extra height allowing you to slide very thick projects under the
foot.
CHANGING THE PRESSER FOOT
Press the ON/OFF switch to OFF.
1. Make sure the needle is in the highest position and the
presser foot is lifted. Pull the presser foot towards you.
2. Line up the cross pin on the foot with the gap in the
presser foot ankle. Push back until the foot snaps into
place.

1
2
A B C
10 – GETTING READY TO SEW
CHANGING THE NEEDLE
Press the ON/OFF switch to OFF.
1. Loosen the screw in the needle clamp with the screwdriver.
2. Remove the needle.
3. Push the new needle upwards with the at side away from
you until it will go no further.
4. Use the screwdriver to tighten the screw properly.
NEEDLES
The sewing machine needle plays an important role in
successful sewing. To ensure you will get a quality needle, we
recommend needles of system 130/705H.
Universal needle (A)
Universal needles have a slightly rounded point and come in a
variety of sizes. For general sewing in a variety of fabric types
and weights.
Stretch needle (B)
Stretch needles have a special scarf to eliminate skipped
stitches when there is a ex in the fabric. For knits, swimwear,
eece, synthetic suedes and leathers. Marked with a yellow
band.
Denim needle (C)
Denim needles have a sharp point to penetrate tightly woven
fabrics without deecting the needle. For canvas, denim,
microbers. Marked with a blue band.
Tip: Read more about different needles in the HUSQVARNA
VIKING®Accessory Catalogue at www.husqvarnaviking.com.
Note: Change the needle often. Always use a straight needle with a sharp
point (1). A damaged needle (2) can cause skipped stitches, breakage of
needles or snapping of thread. A damaged needle can also damage the
stitch plate.

GETTING READY TO SEW – 11
SPOOL PINS AND SPOOL CAPS
Your sewing machine has two spool pins, a main spool pin and an auxiliary spool pin. The spool pins are designed for all types
of thread. The main spool pin is adjustable and can be used in a horizontal position (the thread reels off the stationary spool) or
in a vertical position (the thread spool rotates). Use the horizontal position for all regular sewing threads and the vertical position
for large spools or specialty threads.
Auxiliary Spool Pin
The auxiliary spool pin is used when winding a bobbin from
a second spool of thread or for a second spool when sewing
with a twin needle.
Lift the auxiliary spool pin up and to the left. Slide on a spool
cap. For spools smaller than the medium size spool cap, place
a felt pad under the thread spool to prevent the thread from
reeling off too fast. For larger spools, the felt pad should not
be used.
Horizontal Position
Place a spool cap and the thread spool on the spool pin. Make
sure that the thread reels off the spool counter clock-wise and
slide on a second spool cap. Use a spool cap slightly larger
than the thread spool.
The at side of the spool cap should be pressed rmly against
the spool. There should be no space between spool cap and
thread spool.
A small spool cap is included as an accessory for your
machine. The small spool cap can be used for small thread
spools.
Note: Not all thread spools are manufactured in the same way. If you
experience problems with the thread, turn it in the opposite way or use the
vertical position.
Vertical Position
Lift the spool pin up and all the way to the right. Lock the
spool pin in the vertical position by slightly pressing it down.
Slide on the large spool cap. For spools smaller than the
medium size spool cap or when using specialty threads, place
a felt pad under the thread spool to prevent the thread from
reeling off too fast. For larger spools, the felt pad is not
needed.
Note: No spool cap should be placed on top of the spool as this prevents
the spool from rotating.

D
CA
B
E
12 – GETTING READY TO SEW
THREADING THE UPPER THREAD
Make sure the presser foot is raised and the needle is in the up
position.
Press the ON/OFF switch to OFF.
1. Place the thread on the spool pin and the spool cap on the
spool pin as described on page 11.
2. Spool pin in horizontal position:
Bring the thread over and behind the pre-tension thread
guide (A) and under the thread guide (B).
Spool pin in vertical position:
Instead of bringing the thread into the pre-tension guide
(A), bring it directly under the thread guide (B).
3. Bring the thread down between the thread tension discs
(C).
4. Continue threading in the direction indicated by the
arrows. Bring the thread from the right into the slot on the
take-up lever (D).
5. Take the thread down and behind the last guide just above
the needle (E).

1. 2.
3.
4.
A
B
C
5.
GETTING READY TO SEW – 13
NEEDLE THREADER
The needle must be in the up position to use the built-in
needle threader. We also recommend lowering the presser foot.
1. Use the handle to pull the needle threader all the way
down, catching the thread under the guide (A).
2. Push back to bring the needle threader forward until the
metal anges cover the needle. A small hook will pass
through the needle eye (B).
3. Place the thread under the anges in front of the needle,
so the thread catches into the small hook (C).
4. Let the needle threader gently swing back. The hook pulls
the thread through the needle eye and forms a loop behind
the needle.
5. Pull the thread loop out behind the needle. Place the
thread under the presser foot.
Note: The needle threader is designed to be used for size 70-120 needles.
You cannot use the needle threader for size 60 needles or smaller, the wing
needle, twin needle, triple needle or when the Sensor One-Step Buttonhole
Foot is on. There are also some other optional accessories that require
manual threading of the needle.
When threading the needle manually, make sure that the needle
is threaded from front to back. The white presser foot ankle
makes it easy to see the eye of the needle. The bobbin case
cover can be used as a magnifying glass.
CUTTING THE THREAD
Once you have nished sewing, cut the threads by raising the
presser foot and pulling the threads from the front to the back
into the thread cutter on the left side of the machine.

A
B
D
C
14 – GETTING READY TO SEW
THREADING FOR TWIN NEEDLE
Press the ON/OFF switch to OFF.
1. Insert a twin needle.
2. Use a second thread spool or wind a bobbin with the
thread you are going to use as the second upper thread.
3. Lift the spool pin up and all the way to the right. Lock
the spool pin in the vertical position by slightly pressing
it down. Slide on a spool cap. For spools smaller than the
medium size spool cap, place a felt pad under the thread
spool.
4. Place the rst thread spool on the spool pin. The spool
should rotate in a clockwise direction when the thread reels
off the spool.
5. Left needle: Thread the machine as described on page 12.
Check to ensure that the thread lies between the left thread
tension discs (A). Thread the left needle manually.
6. Pull out the auxiliary spool pin and slide on a spool cap.
For spools smaller than the medium size spool cap, place a
felt pad under the thread spool.
7. Place the second thread on the spool pin. The second
spool should rotate in a counterclockwise direction when the
thread reels off the spool.
8. Right needle: Thread the machine as before but this thread
should lie between the right thread tension discs (A) and
outside the needle thread guide (B). Thread the right
needle manually.
Note: If using specialty threads (such as metallic threads) its weight and
irreglular surface increases the thread tension. By reducing the tension, the
risk of needle breakage is prevented.
Note: Only use symmetrical twin needles (C).
Do not use this type of twin needle (D), since
it may damage your sewing machine.

C
A
BC
D
D
GETTING READY TO SEW – 15
WINDING THE BOBBIN WITH
THE MACHINE THREADED
Make sure that the presser foot is up and the needle is in the
highest position.
Note! Do not use a plastic presser foot when bobbin winding.
1. Place an empty bobbin on the bobbin spindle on the top
of the machine. The bobbin only ts on one way, with
the logo facing up. Use only original HUSQVARNA
VIKING®bobbins.
2. Pull the thread from the needle under the presser foot and
to the right through the thread guide (C).
3. Guide the thread through the hole in the bobbin (D) from
the inside to the outside.
Note: When using an earlier version of HUSQVARNA VIKING®
bobbins that do not have a hole, wind several turns of thread on the
bobbin to get started.
4. Push the bobbin spindle to the right. A pop-up message
appears on the TouchScreen. Hold the end of the thread
rmly when starting to wind. Press the foot control to
start winding. Once the bobbin begins to wind, cut the
excess thread. When the bobbin is full it will stop rotating.
Push the bobbin spindle back to the left, remove the
bobbin and cut off the thread on the thread cutter.
WINDING THE BOBBIN USING
THE VERTICAL SPOOL PIN
1. Place an empty bobbin on the bobbin spindle on the top
of the machine. The bobbin only ts on one way, with
the logo facing up. Use only original HUSQVARNA
VIKING®bobbins.
2. Place the large spool cap and a felt pad under the spool on
the main spool pin set in the vertical position.
3. Bring the thread over and behind the pre-tension thread
guide (A) and down around the thread tension disc (B),
then through thread guide (C) as illustrated.
4. Guide the thread through the hole in the bobbin (D) from
the inside to the outside.
5. Push the bobbin spindle to the right. A pop-up message
appears on the TouchScreen. Hold the end of the thread
rmly when starting to wind. Press the foot control to
start winding. Once the bobbin begins to wind, cut the
excess thread. When the bobbin is full it will stop rotating.
Push the bobbin spindle back to the left, remove the
bobbin and cut off the thread on the thread cutter.
Note: When using an earlier version of HUSQVARNA VIKING®
bobbins that do not have a hole, wind several turns of thread clockwise
on the bobbin to get started.

E
F
G
1. 2.
3. 4.
I
H
16 – GETTING READY TO SEW
WINDING THE BOBBIN USING
THE AUXILIARY SPOOL PIN
1. Place an empty bobbin on the bobbin spindle on the top
of the machine. The bobbin only ts on one way, with
the logo facing up. Use only original HUSQVARNA
VIKING®bobbins.
2. Fold out the auxiliary spool pin. Place a spool cap and a
felt pad under the spool.
3. Bring the thread over and behind the pre-tension thread
guide (A) and down around the thread tension disc (B),
then through thread guide (C) as illustrated.
4. Guide the thread through the hole in the bobbin (D) from
the inside to the outside.
5. Push the bobbin spindle to the right. A pop-up message
appears on the TouchScreen. Hold the end of the thread
rmly when starting to wind. Press the foot control to
start winding. Once the bobbin begins to wind, cut the
excess thread. When the bobbin is full it will stop rotating.
Push the bobbin spindle back to the left, remove the
bobbin and cut off the thread on the thread cutter.
INSERTING THE BOBBIN
Press the ON/OFF switch to OFF.
1. Remove the bobbin cover by sliding it towards you.
2. Place the bobbin in the bobbin case. It drops in only one
way with the logo facing up. The thread unreels from the
left of the bobbin. The bobbin will then rotate counter-
clockwise when you pull the thread.
3. Place your nger on the bobbin to keep it from turning as
you pull the thread rmly to the right and then to the left
into the tension spring (E) until it “clicks” into place.
4. Continue threading around (F) and to the right of the
thread cutter (G). Slide on the bobbin cover (H). Pull the
thread to the left to cut (I).
AUTOMATIC THREAD TENSION
Your machine automatically sets the best thread tension for
the selected stitch and fabric. The thread tension shown on the touchscreen can be adjusted for specialty thread, techniques or
fabric. Touch + to increase the thread tension and - to decrease it.
A
BC
D