Hussmann Impact M1GLE-93 User manual

All equipment should be thoroughly examined for
shipping damage before and during unloading.
This equipment has been carefully inspected at
our factory. Any claim for loss or damage must
be made to the carrier. The carrier will provide
any necessary inspection reports and/or claim
forms.
Every effort is made to ship all parts for the kit.
The Hussmann Service Center can be reached by
calling
• from U.S. & Canada 1-800-922-1919 •
• from Mexico 1-800-522-1900 •
Merchandisers
®
M1GLE-93
Joining
Back-to-Back
PARTS LIST
(One Joining Kit per Two M1GLE-93)
Item Quantity Description
1. 6 Screw – Phillips Head – #8-18 x 1/2
2. 2 Gasket Tape 1 x 1/2 x 180
3. 2 Cap Screw 5/16 -18 x 3 1/2in.
4. 8 Flat Washer 5/16
5. 4 Lock Washer 5/16
6. 4 Hex Nut 5/16 -18
7 2 Cap Screw 5/16 -18 x 5 1/2in.
8. 1 Silicone Sealer
9. 1 Top Trim – 10 1/2in. x 84-in.
10. 2 Top Rail Trim
11. 2 Bumper – Top (CUT TO FIT)
12. 2 Bumper – Bottom (CUT TO FIT)
13. 8 Bracket — End Splashguard
14. 20 Screw – SM Hex Head – TEK2 – #8-18 x 1/2
15. 2 Splashguard Support
1
P/N 0503478_A
April 2008
©2008 HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
U.S. & CANADA 1-800-922-1919 • MEXICO 1-800-522-1900 • WWW.HUSSMANN.COM

JOINING BACK-TO-BACK
Joining two end case requires
different parts and procedures
than are used to join an end
case to a line-up. Please follow
these instructions to assure
satisfactory performance, fit
and finish.
1On the back of each case,
replace screws and
remove studs.
Replace all 1/4in. Hex
head screws on the back
of each case with
Phillips Head Screws – 1
supplied.
Remove (or cut flush) the
studs used in normal case
joining.
2Position first case.
All cases must be level to
ensure correct operation.
Place the first case in
position, then check for
level front-to-back and
side-to-side. Use the
provided metal shims to
level the case. Place shims
under front and back rail
at cross-members.
Figure 1 — Remove Studs and Replace Screws
P/N 0503478_A
2U.S. & Canada 1-800-922-1919 • Mexico 1-800-522-1900 • WWW.HUSSMANN.COM
Figure 2 — Position and Level First Case
Levels
Serial Plate

3Remove the honeycomb
as shown in Figure 3.
4Lift up and out to remove
the interior back panels.
Refer to Figure 4 for
location.
M1LGE-93 Joining P/N 0503478_A
3
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. • WWW.HUSSMANN.COM
Figure 4 — Remove Interior Back Panels
Interior
Back Panels
Figure 3 — Remove Honeycomb
Honeycomb

5Insert Alignment Pins
Each case ships with
alignment pins that are
inserted in end frames or
other mating surfaces to
facilitate positioning.
Refer to Figure 5 for
correct placement.
6Apply Gasket
Apply Gasket – 2 as
indicated in Figure 5.
Gasket should be inset
1/4-in from edge, and
extend up the sides to the
glass.
The same gasket arrange-
ment is used both cases.
Assure good adhesion of
gaskets by wiping the end
frame with rubbing alcohol
to remove any accumulated
dust and oils.
Apply silicone sealant
above gasket as shown in
Detail
Remove paper backing
before proceeding to next
step.
P/N 0503478_A
4U.S. & Canada 1-800-922-1919 • Mexico 1-800-522-1900 • WWW.HUSSMANN.COM
Figure 5 — Apply Gaskets
1 in. Gasket
(24 mm) Insert
Alignment Pins
Insert
Alignment
Pins
Apply Gasket up to
Glass onEach Side
IMPORTANT
• Do not stretch gasket, especially around corners.
• Do not butt gaskets; always overlap them as shown.
• Remove paper backing after gasket has been applied.
• Perimeter gasket required by NSF.
A continuous bead of
silicone sealant/ caulk
may be used in addition
to gaskets on mating
surfaces but must not be
used in lieu of gaskets.
Detail

7Position Second Case
Alignment pins guide the
mating of the frames.
Insert Cap Screw – 3
through Flat Washer – 4,
then through frame
into nut retainer.
Add Flat Washer –- 4,
Lock Washer –- 5 and
Hex Nut – 6. Tighten to
draw side frames together.
8From the front of one case,
use a long (10 1/2in.) bit to
drill a 3/8in. hole in each
end frame behind honey-
comb. Drill through both
cases. On each side, insert
Cap Screw – 7 through
Flat Washer –- 4, then
through both frames.
Add Flat Washer –- 4,
Lock Washer –- 5 and
Hex Nut – 6. Tighten to
draw frames together only
until space between PTM
measures 10 1/4inches.
ANYTHING LESS THAN
10 1/4 INCHES WILL
DAMAGE THE CASES.
M1LGE-93 Joining P/N 0503478_A
5
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. • WWW.HUSSMANN.COM
Figure 7 — Location of Cap Screws in Side Frames
Figure 8 — Drill Holes in Back Frame
Figure 6 — Move Second Case
Cap Screw
Metal
Washer
Lock
Washer
Nut
Metal
Washer
Case
Frames
31/2-inch
51/2-inch
Minimum 10 1/4inches between PTM
10 1/4

8Use Silicone Sealer – 8
inside to seal the 1-inch
gap between end frames
as shown in Figure 9.
Apply Silicone Sealer – 8
over Cap Screws – 3, over
Cap Screws – 5, and over
Hex Nuts – 7.
9Adjust color panels on
each side to minimize
any gaps.
P/N 0503478_A
6U.S. & Canada 1-800-922-1919 • Mexico 1-800-522-1900 • WWW.HUSSMANN.COM
Figure 9 — Apply Silicone

10 From one side, slide
Top Trim – 9 under
price tag moldings on top
of cases to cover gap as
shown in Figure 10.
11 Remove the protective
film from the stainless
steel top rail, then install
the Top Rail Trim – 10
on each side as shown in
Figure 12.
M1LGE-93 Joining P/N 0503478_A
7
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. • WWW.HUSSMANN.COM
Figure 10 — Install Top Trim
Figure 11 — Install Top Rail Trim
Top Rail Trim
Top Trim
Top Rail Trim

13 The top and bottom
bumpers should be
kept inside a cooler or
refrigerated case for at
least six (6) hours. This
will allow the bumper to
contract.
Remove all remaining
shipping braces. Measure
and cut Top Bumper – 11
and Bottom Bumper – 12.
Use a miter box and fine-
tooth saw to cut bumpers
to length. Install the top
and bottom bumpers.
Remove protective film
from the bumpers once
installation is complete.
14 Replace interior back
panels.
Replace honeycomb and
retainers as shown in
Figure 15.
P/N 0503478_A
8U.S. & Canada 1-800-922-1919 • Mexico 1-800-522-1900 • WWW.HUSSMANN.COM
Figure 13 — Remove Braces and Install Bumpers
Honeycomb
Figure 15 — Replace Honeycomb
Figure 14 — Remove Protective Film
Miter Box
Bumper
Shipping
Braces
Shipping
Braces

15 Attach the Splashguard
Brackets – 13 to side of
legs using Screws – 14.
Attach Splashguard Joint
Supports – 15 using
Screws – 14. Refer to
Figure 16.
16 Install splashguards.
Adjust to minimize
any gap at joint.
1. Check to be sure that all
splashguard brackets are
level with the floor.
2. Position top of splashguard
over the top edge of the
bracket as shown below.
3. Push the lower edge of the
splashguard toward the bot-
tom of the bracket until it
snaps into place.
M1LGE-93 Joining P/N 0503478_A
9
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. • WWW.HUSSMANN.COM
Figure 16 — Install Splashguard Brackets
Joint Support
Screw
Splashguard
Brackets
Figure 17 — Install Splashguards
3.
Splashguard
2.
Bracket Base of
Case
1.
Splashguard