Hutchee PureSound H100 User manual

USER GUIDE
PureSound H100 - Wireless Headset

HEADPHONE CONTROLS
* All Controls Are on the Right EAR PIECE
* MFB = Main Function Button/Power Button
Thank you for choosing the PureSound H100 Wireless Headset.
RUN, PLAY, LAUGH & ENJOY THE SOUND.
FUNCTION OPERATION
Power ON > Hold MFB for 3 seconds
Power OFF > Hold MFB for 3.5 seconds
Pairing Mode > While off, hold MFB for 6.5 seconds
ANSWER Call or END Call > Short press MFB once
REJECT / IGNORE Call > Hold MFB for 1 second
REDIAL Last Number > Double press MFB
CANCEL / END > Short press MFB once
PAUSE / PLAY > Short press MFB once
VOL - or VOL + > Short press -or +
Track BACK or FORWARD > Hold -or +
PureSound H100 Controls >
Volume + / Next Track

Thank you for choosing the PureSound H100 Wireless Headset.
RUN, PLAY, LAUGH & ENJOY THE SOUND.
FUNCTION OPERATION
Power ON > Hold MFB for 3 seconds
Power OFF > Hold MFB for 3.5 seconds
Pairing Mode > While off, hold MFB for 6.5 seconds
ANSWER Call or END Call > Short press MFB once
REJECT / IGNORE Call > Hold MFB for 1 second
REDIAL Last Number > Double press MFB
CANCEL / END > Short press MFB once
PAUSE / PLAY > Short press MFB once
VOL - or VOL + > Short press -or +
Track BACK or FORWARD > Hold -or +
Charging >
• Connect Micro USB (provided) to any USB charging device.
Fully charged in 1-2 Hours.
• You can expect the best performance on full charge.
Volume Control >
• Volume + / - (controls volume level).
LED >
• While usb is connected: Red light indicates charging, Blue light indicates
full charge.
• Red light flashing twice indicates low battery, (low battery voice prompt).
PureSound H100 Controls >
Front
Volume - / Previous Track
USB Charger
Back
Speaker
Ear Bud
Volume + / Next Track
Main Function Button (MFB)

Connecting/Pairing your Bluetooth Headset >
1. When headset is turned off, Hold the MFB (6 seconds), until the
headset LED is flashing red and blue (pairing state voice prompt)
headset is now in pairing state, searching for a device to pair with.
2. Turn bluetooth on for mobile phone or other bluetooth device, press scan.
Wait until the name ‘PureSound H100’ displays.
3. Click ‘PureSound H100’ to connect. After the connection is successful,
the headset’s blue light will flash.
4. Password: 0000 - Some devices may require password to connect/pair.
*** Your headset should now be paired / connected. ***
Multi-Point Function Steps >
1. Turn off Bluetooth for the mobile phone or device already paired.
2. Repeat steps 1-4 above for the 2nd Bluetooth device.
3. Turn Bluetooth function back on for original device. Find the wireless
Headset, click connect to activate multipoint.
Reconnecting your Headset >
Headset will try to reconnect automatically. If the headset does not try to
reconnect, press the MFB once and go to phone/device Bluetooth menu to
reconnect manually.

TROUBLESHOOTING YOUR HEADSET
Mobile phone or device can’t find headset >
>>> Solutions:
• Confirm if the headset is turned on. (Whether the LED indicator light is on
or Red and Blue lights are flashing).
• If the headset is turned on but it still can’t be found, please restart your
phone/device and the headset.
After reconnecting the headset with your phone/device,
there is always static, noise or it disconnects >
>>> Solutions:
The wireless headset’s battery is low, charge the headset.
Bluetooth’s radio frequency is blocked by water, and the human body is made
up of mostly water. If you keep your phone in your left pocket it is possible,
that the connection may be weak. This can cause some interference issues.
Trying holding your phone in your hand or placing it in your right pocket. If
you wear an armband, try placing it on your right arm.

MORE TROUBLESHOOTING INFORMATION
Max distance between headset and Bluetooth device >
The max distance between headset and device is 10 meters in clear line of
sight. If you exceed the max distance, or if too many things are blocking the
clear line of sight, the signal may fade and cause other connectivity issues.
The red light is not on while charging >
The headset has been idle for a long time and has not been used.
Charge the headset for about 30 minutes, then the red light should light up.
*** Note: Overcharging headset or prolonged exposure to high temperature
will reduce the capacity and life of the headset battery. Be mindful of leaving
the headset exposed to the sun, in your car or by a window. When not in use
keep your headset in the provided case for battery longevity.
Restore Factory Settings >
Hold the MFB for 3 seconds while charging, until the red and blue lights flash
three times to restore factory settings.

CUSTOMIZE YOUR HEADSET FOR THE PERFECT FIT
Accessories in the headset box >
In addition to the USB charging cord there are a selection of ear bud sizes and
a plastic toggle for the headset connecting wire.
If your ear buds are uncomfortable you may need to choose a smaller ear bud
size. If they slip out of place during use or exercise, a larger ear bud may be
the right fit for you.
Changing the ear bud for your comfort >
Pull off the rubber ear bud to be replaced. Snap on the new ear bud. Apply
gentle pressure and the ear bud will pop over the in ear speaker.
Applying the cord toggle >
The cord toggle simply takes up any slack in the cord for a more comfortable
experience. Pinch a small loop in your headset cord. Push the flat part of one
side of this loop through the toggle, then the other side. In each case twist the
cord in the toggle opening to secure. You should now have an adjustable loop.
While wearing the headset slide the toggle closer or further from your neck to
take up any slack in the cord.

Thank you from all of us at Hutchee, Inc. We hope you
enjoy your new wireless headset.
If you have any issues or questions please email
[e-mail]