HuTools HT01 User manual
Hold the latch in front of the door
hole, with the latch face flush
against the door edge. Is the sloed
hole centered in the door hole?
Is the door edge chiseled?
Prepare the door and check dimensions
Determine backset and adjust the latch
Install strike and test alignment
Install the latch
Rotate and pull the latch
as shown to extend latch.
NO
Sloed hole is
NOT centered.
YES
Sloed hole is centered.
No adjustment is required.
Proceed to next step.
1
(70mm)
2
chiseled
not chiseled
12
34
Install latch in door with wood block and
hammer.
Installation
Contents
B (Optional)
Latch ×1
A
Drive-In Collar ×1
B
Strike ×1
C
Exterior Assembly ×1
D
E
Interior Assembly ×1
F
G
Strike Screws ×2
H
Latch Screws ×2
I
Interior Assembly Screws ×3
J
Key ×1
K
L
Installa�on Overview
Read this manual carefully before installing and operang!
If any parts are missing or damaged, please contact Customer Support.
STEP
2
STEP
3
backset
60 or 70 mm
STEP
1
NO
YES
IMPORTANT: Make sure hole in
door frame is drilled a minimum
STEP
4
ST4*22
Actual Size
I
H
C
B
TOOL REQUIRED: USE OF A POWERED
SECREWDRIVER IS
NOT RECOMMENDED
test if deadbolt works
smoothly.
strike or door frame.
Install the physical lock
(Step 1-7)
Detect door orientaon
(Step 8-9)
Change the default master code
(See Quick Set Up)
(See Quick Set Up)
Customize seng
1
2
3
4
HuTools HT01
Installation Guide
Read this manual carefully before installing and operating!
D
F
I
A
E
J
G
C
H
L
K
7A
lock is completely installed.
IMPORTANT: Test the thumbturn
Install exterior assembly
Door handing
Test the lock
retracted.
Install interior
assembly
OPENED and
Test with the door open to avoid an accidental lockout.
Rotate the thumbturn and
fully retracted (unlocked).
Insert the cable connector to
the socket. Push the connector
seated.
unlocked
unlocked
STEP
8
STEP
STEP
9
STEP
5
STEP
6
STEP 7B
7C
A
STEP
8B
STEP
STEP
5A
B
Do not release
Lock
Unlock
on keypad
Enter 12345678
FG
Actual Size
M4*6
K
Actual Size
1/4-28*55
J
NOTE:
Press and hold any buon for 2 seconds.
the latch.
unlocked
unlocked
reset
Horizontal
83618 137192 14710
password
Random digits
UNLOCK the door from outside
You need to enable this feature by
.
Master code User codeOr
Programming Instruction
How To Use
Programming Basic
LOCK the door from outside
Auto Lock Mode
The default master code is 12345678. This code must be changed
prior to programming the lock.
The Master Code is used for programming and for feature sengs.
It will also unlock the lock.
Manual Mode
A.
Master Code
A.
B.
Quick Set Up
IMPORTANT:
Please start over.
Master Code New User Code
Enter the New User Code Again
2
Add User Code
B.
Up to 20 User Codes can be stored.
Aer 10 unsuccessful aempts at entering a valid PIN code, the unit
will shut down for 3 minuets.
Wrong Entry Limit
C.
If you hear 10 beeps corresponding with 10 red flashes aer pressing
any key or lock and unlock the door, that's an indicaon that the
baeries need to be replaced soon. Please replace with 4 new AA
alkaline baeries and do not mix old and new baeries. All sengs
are retained in the memory when the baeries are removed and
replaced.
E.
Key Override can be used to gain access when the baeries are
completely dead or when no valid User Code is known.
Important Note:
Please keep at least one copy of the backup key in secure locaon
outside of your place.
Key Override
F.
User can prevent pin code exposure from strangers by entering
random digits before or aer pin code.
Unlock with Fake code
D.
a. Forward number sequence
c. Repeat number sequence
5679
5
679
65
If
Then
and
965
965
Code is 4-10 digits.
Both master code and user code do not support the following
sequence.
Code Format
B.
Master Code New Master Code
Enter the New Code Again
1
Change Master Code
A.
3
Master Code Unwanted User Code
Delete User Code
C.
4 2
Master Code
Enable Silent Mode
D.
The beep sounds when pressing keypad can be muted. But you
will sll hear low baery and system alerts.
Disable Silent Mode
E.
4 1
Master Code
Enable Auto Lock
F.
Automacally locks the deadbolt 30 seconds aer unlocking.
This feature is off by default.
Disable Auto Lock
G.
5 2
Master Code
Vacation Mode
J.
This is a security feature for you when you are leaving your home
for vacaon or long trip. Enabling vacaon mode will restrict all
user codes unl master code is entered on keypad. If the lock is
unlocked by thumb turn, the lock will sound an alarm.
6
Master Code
Set Auto Lock Time Delay
H.
You can set the Auto Lock me delay between 10 and 99 seconds.
8
Master Code Enter New Duraon Time(10-99)
Add One-Time Code
I.
This code can only be used once and is automacally deleted
when used.
Enter the New User Code Again
7
Master Code New Master Code
5 1
Master Code
Master Code
Auto Lock
Silent Mode
Wrong Code Entry Limit
Vacaon Mode
Factory Defaut
12345678
Disabled
Disabled
10 mes
Disabled
Factory Default Sengs
How To Reset
Safety Warnings
Troubleshoong（connued）
Troubleshoong
Protect your User Codes and Master Code.
Restrict access to your lock’s interior assembly and rounely check your
sengs to ensure they have not been altered without your knowledge.
Proper cleaning and maintenance of your lock ensures it will connue to
work as it should.
Do not apply cleaner or detergent directly to any part of the lock.
The HuTools meets IP54 water-resistance. It can withstand water
splashes ; however, do not let water and liquids get into the lock.
Avoid exposure to direct sunlight. Long-term exposure to direct sunlight
may damage the lock.
The temperature range of the HuTools is between -4°F to 131°F.
Keep the door opened and make sure the latch is retracted and
thumbturn vercal.
Step1
Press and hold the reset buon with one hand and the other
hand takes out one baery and places it back.
Step2
Do not release the reset buon aer baery is connected,
instead, keep holding it unl the latch automacally extends.
Step3
Problem:
(A)
b. Make sure you reset the lock with the door opened.
(A)
(
(
(
(
Problem:
(A)
(A): The lock is not installed properly.
(
(
Problem:
: The lock is not reset properly.
Problem:
: a. Make sure the cable is properly connected.
: The lock has no power.
Problem:
: a.
deep so the bolt fully extends.
the deadbolt strike or door frame.
Problem:
: Make sure your door locks and unlocks smoothly. your
Problem: The lock does not lock and unlock electronically.
1
4
2
6
7
Problem:
8
Problem:
: a.
9
10
Problem:
to factory default.
12
Problem:
11
Problem:
: a.
b. Do not insert the physical key before lock is completely install.
: The lock is not installed properly.
5
3
Other manuals for HT01
1
Other HuTools Lock manuals
Popular Lock manuals by other brands
Babypeta
Babypeta Stick'n'lock installation instructions
Assa Abloy
Assa Abloy Corbin Russwin IN120 installation instructions
Snap-loc
Snap-loc E-TRACK SINGLES manual
Simons Voss Technologies
Simons Voss Technologies LockNode SREL2.G2 quick guide
Griffon
Griffon GRIFFON manual
PORT
PORT GUARD installation guide
