Hwasung HMC-081 User manual

Technical Manual (Model : HMC-081 /HMK-081 / HMKP-081)
*Technical Manual = User manual
Model : HMK-081
Model : HMKP-081
HWASUNG SYSTEM CO.,LTD
<NOTICE> . All features and specifications described are subject to charge without notice.
. If you have any questions, please contact us.

CAUTION
•Please do not disassemble / reorganize the product.
•Please do not the remove the paper jam during power on.
•Pleased do not exceed the standard power voltage.
•Please do not wash off the product.
•Please do not press / shock the product.
•Please do not put the product at the moist (humid) condition.
•Please contact us if there is any problem.
•Please power off once remove the paper jam.
•Please clear the air / open the disclosed place.
•Please set the product without damage enviornment.
•Please set the product at the stable place.
•Pleaes keep the requires as necessary as general electrics.
Title Rev. Page
HMK(P)-081,HMC-081 Ver1.0
2

CONTENTS
1. Printer features & External dimension 4
1-1) Name of each parts 4
1-2)Dimension 5
1-3) Model number 6
2. Operation 8
2-1) Paper width 8
2-2) Paper set up 9
2-2-1) Clam shell type 9
2-2-2) Auto loading 10
2-3)Paperjam 11
2-4)Selftest 13
2-5)HEXDump 14
2-6) Onboard update 15
2-7) Dip switch 16
2-8)Memoryswitch 18
2-9) Internal connector 20
2-10)Presenter 23
3. Genearl Specification 24
3-1) Specification 24
3-2)Power 24
3-3) Paper loading capacity 24
3-4) Weight 24
3-5) Operation condition (temperature / Humid) 24
3-6) Storage condition (temperature / Humid) 24
3-7) MCBF 24
4. Interface Specification 25
4-1) RS232C 25
4-2)USB 25
4-3) Ethernet 25
5. Command 26
6. Windows Driver 54
6-1) Set up the function 54
6-2) Set up the paper 55
6-3) Set up the new paper 56
7. Ticket recommend 58
8. OCX driver(USB) 60
9. How to set up Ethernet 64
10. Revision reference 66
Title Rev. Page
HMK(P)-081,HMC-081 Ver1.0
3

1. Printer features & External dimension
1-1) Name of each parts
1 2 3 4
Auto cutter
Paper shaft
Paper near end sensor
Paper holder
Open lever
Mechanism
Frame
(control board mount)
5 6
1.Power switch.
2.Error LED.
3.Power LED.
4.Feed switch.
5.Dip switch 1
6.Dip switch 2
7.DC Jack (24VDC)
8.Serial connector (RS232C, Straight ,Female 9 pin)
9.USB connector (USB, Type B)
10.Ethernet connector (Ethernet) : Option
7 8 9 10
REAR
BOTTOM
Presenter
[Image1-1]
[Image1-2]
[Image1-3]
[Image1-4]
Paper guide (Mouse)
Title Rev. Page
HMK(P)-081,HMC-081 Ver1.0
4

1-2) Dimension
[Image1-6] Standard type
Title Rev. Page
HMK(P)-081,HMC-081 Ver1.0
5

[Image1-7] Presenter type
Title Rev. Page
HMK(P)-081,HMC-081 Ver1.0
6

1-3) Model number
HM□□-081□
※Interface
(blank) : RS-232C & USB combo
E : Ethernet(LAN)
※Frame
K : Frame type.
C : Board type.
※Presenter
(blank) : Standard type.
P : Presenter type.
Title Rev. Page
HMK(P)-081,HMC-081 Ver1.0
7

2. Operation
2-1) Paper width
Title Rev. Page
HMK(P)-081,HMC-081 Ver1.0
8
* Please adjust the paper guide,
and screw two pcs 3x4.
* Please refer to the image Image 2-2.
2-3 inch
* There are two sides for the paper guide.
One is on the left, The other is on the right.
* Please refer to the Image 2-1.
[Image 2-1]
[Image 2-2]
* There are two types of paper guide.
* One is the paper guide for the left side.
* The other is the paper guide for the right side.
* It is the same way to adjust / screw,
even it’s the left side, or it’s the right side.
Paper guide

2-2) Paper set up : There are two ways to change the paper set up.
2-2-1) Clam shell type
1. Please press down the ‘open lever’ and open the ‘cover’.
2. Please inser the paper.
[그림2-5]
[Image 2-6]
Please make sure about the paper side which is printed.
Please refer to the image [Image 2-8].
Notice : Please insert the paper, till the paper comes out from
the cutter.
3. Please close the cover as [Image 2-9].
Please press the feed button, and make sure if the paper feeds.
It is to make sure about if the paper set up correctly.
[Image 2-8]
[Image 2-7]
Notice : If the paper doesn’t feed correctly, you open the cover
and try to set up the paper again.
[Image 2-9]
Title Rev. Page
HMK(P)-081,HMC-081 Ver1.0
9

2-2-2) Auto loading
1. Please switch on the power.
2. Please cut the paper off as the image [Image 2-11].
Title Rev. Page
HMK(P)-081,HMC-081 Ver1.0
10
3. Please insert the paper, till the paper comes out from
the cutter.
* You can see the paper is loading automacially, and
the printer feeds and cuts the paper.
Notice: it’s normal, even you hear the motor sound.
[Image 2-10]
[Image 2-11]
Notice : If it is a type of presenter type, please remove the paper inside of the presenter, and
set up the paper.

2-3) Paper Jam
Please follow the instructions, when it occurs the paper jam.
1.Please switch off the power, and make sure if the cutter blade prevents
the paper from feeding / printing.
Cutter blade is not preventing
Cutter blade is preventing the paper
from feeding and printing.
2. Please use the knob and turn one direction, and make sure about if the cutter blade is
not preventing, or is preventing the paper from feeding and printing.
Title Rev. Page
HMK(P)-081,HMC-081 Ver1.0
11
Knob

3. Please turn the captive screw ①as counterclockwise.
Title Rev. Page
HMK(P)-081,HMC-081 Ver1.0
12
Notice Please do not use any knife, or any sharp device, so that the platen roller doesn’t hurt.
Notice The above image about the presenter type.
The standard type is the same with the presenter type as image above,
when you remove the paper jam.
Notice Please make sure about you turn off the power, when you remove the paper jam.
4. Please press down the open lever ②,③
and remove the paper jam.
④
①
③
②

Title Rev. Page
HMK(P)-081,HMC-081 Ver1.0
13
2-4) Self-test
Please turn off and on the power, while you press down the feed button.
You can see the following informations are being feeded.
zModel.
zFirmware version / creare date.
zInterface.
zDip switch.
zSample.
NoticePlease refer to the specification of Dip switch 2-7).

2-5) HEX Dump
Please power on after the dip switch 8 (up) of 1.
Then it prints all data in hex character (16 antilogarithm),
after [Hex Dump Mode] prints out as ‘[Printing sample]’.
It could know the printer status. It will be useful for the application development.
zIt prints, if the data receives the digit 12.
zPlease press the feed button, if the data receives less than the digit 12.
zThe control code ( 1F16 below) prints “.”.
zThe 8016 above prints “^”.
[Printing sample]
A
SCII
16 antilogarithm
[HEX DUMP MODE]
41 42 43 44 45 46 47 47 49 4A 4B 4C
30 31 32 33 34 35 36 37 38 39 1B 4A 013 4 56789. J2
FF ^ .i
AB C D E F G H I J K L
1B
69
Title Rev. Page
HMK(P)-081,HMC-081 Ver1.0
14

Title Rev. Page
HMK(P)-081,HMC-081 Ver1.0
15
2-6) Onboard update
Please conduct the updates, after refering the following steps.
1) Please switch off and on, after you lift *up the eighth (8th) of Dip Switch 2.
Then the error LED (red) will be lighted on, after the light goes in and out as twice.
* up : on.
2) Please check the connection between the printer and the data cable.
* Please make sure about if it is the right cable.
3) Please conduct the given program.
If the error LED is turned off and is lighted on slightly after 4 seconds,
then the updated is being started.
* Please do not switch off the printer power, till the update is complete.
4) The update will be complete, once the update indicates complete.
* If the error LED keeps the light goes in and out, it’s error.
Please stop the update program and make sure the cable and other connections.
Please return the process “1.” and follow the step again.
5) Please lift *down the eigth (8th) of Dip Switch 2,
and power off/on the printer, and use the printer.
*down : off.

2-7) Dip switch
Please control the dip switch between the printer & the host for the protocol condition.
There are 1 and 2 of dip switch.
1)Dip switch 1
※RS-232C (Dip2 SW4) ※Ethernet mode (Dip2 SW4)
a)1 : Ethernet IP mode
SW1 IP Mode
ON DHCP IP(DHCP)
OFF Static IP
a)1,2,3 : Baud rate
SW1 SW2 SW3 Baud Rate(BPS)
OFF OFF OFF 1200
ON OFF OFF 2400
OFF ON OFF 4800
ON ON OFF 9600
OFF OFF ON 19200
ON OFF ON 38400
OFF ON ON 57600
ON ON ON ---
b)2 : Ethernet booting mode
SW2 Boot Mode
ON Factory mode.
It sets up the mode by the
factory.
OFF User mode.
It sets up the model by the
user.
※Notice :
please refer to how to set up the ethernet.
b)4 : Data bit
SW4 Data bit
ON 7
OFF 8
c)5,6: Paraity
SW5 SW6 Paraity
OFF OFF None
ON OFF Even
- ON Odd
d)7 : Stop bit
SW7 Stop bit
OFF 1 STOP
ON 2 STOP
e)8 : Print mode
SW8 Print mode
ON HEX DUMP
OFF NORMAL
2)Dip switch 2
a)1: Realtime command valid / invalid
SW1 Realtime command valid / invalid
ON DLE Command on
OFF DLE Command off
Title Rev. Page
HMK(P)-081,HMC-081 Ver1.0
16

Title Rev. Page
HMK(P)-081,HMC-081 Ver1.0
17
b) 2 :
SW2 Black Mark valid/invalid Description
ON Black Mark valid After the black mark is detected,
the initial paper is positioned.
OFF Black Mark invalid The black mark of the initial paper is not detected.
Notice : If it’s valid, please use the paper with the black mark, or it occurs the paper jam.
Notice : Please make sure the specification of the paper should be the same with the registered
informations.
Notice : Please refer to 2-8) memory switch.
c) 3 :
SW3 First Page Mode Description
ON First Page No Cut The paper is not cut, once the initial paper is positioned.
OFF First Page Cut The paper is cut, once the initial paper is positioned.
Notice : Please make sure the specification of the paper should be the same with the registered
informations.
Notice : Please refer to 2-8) memory switch.
d) 4 :
SW4 RS-232C/Ethernet Mode Description
ON Ethenet Mode Ethernet interface is valid.
OFF RS-232C Mode RS-232C interface is valid.
Notice : You can’t use the interface Ethernet and the interface RS-232C together.
e) 5 :
SW5 JamSensor valid /invalid Description
ON Jam Sensor valid Jam Sensor is valid.
OFF Jam Sensor invalid Jam Sensor is invalid.
Notice : Jam Sensor assembly is option.
Notice : If the Jam sensor assembly is not accomodated and the jam sensor is valid (on),
it dectects the paper Jam. It means it’s not workinig normally.
f) 6 :
SW6 Presenter valid / invalid Description
ON Presenter valid Presenter is valid.
OFF Presenter invalid Presenter is invalid.
Notice : Presenter is option.
Notice : If the presenter is not accomodated and the presenter is valid (on),
it dectects the paper Jam. It means it’s not workinig normally.
g) 7 :
SW7 Reserve Description
ON -----
OFF -----
h) 8 : Update / print mode
SW8 Update / print mode Description
ON Update mode Firmware update mode
OFF Print mode Standard print mode

2-8) Memory switch
Please set the function of internal memory.
※Please use the given program - ‘memory swtich setting utility program’.
※The value is not deleted until the next value is changed, even though power off.
Memory SW Value
SW1 p or m
SW2 0~1200 or 0~136
SW3 248-4000
SW4 Reservation
SW5 Reservation
SW6 Reservation
SW7 Reservation
SW8 Reservation
1) SW1 :
* p(7016) : After command the cutting DC3 + “i”, it will be cut from the black mark starting
point to the value in the SW2 (plus) as the image below.
* m(6D16) : After command the cutting DC3 + “i”, it will be cut from the black mark starting
point to the value in the SW2 (minus) as the image below.
2) SW2 : The distance from the black mark starting point to the cutting position
* SW1 /p : You can set the value as 0~1200(0 ~ 150mm).
* SW1/ m : You can set the value as 0~120(0 ~ 15mm).
※A value point indicates 0.125mm ex) In case of 100, 100 x 0.125 = 12.5mm
※SW1,SW2 is used to set the cutting option (Black mark search as Full cut) at the Window
Driver (Window driver : DC3 + “i”)
Example)
Title Rev. Page
HMK(P)-081,HMC-081 Ver1.0
18
Page 1.
A
BC
A
BC
Page 1.
Black mark
starting point
Cutting Position
Black mark
starting point
Page.2
12.5mm
Page.2
On the back
12.5mm
Cutting Position
Ex) SW1 = p, SW2 = 100, Ex) SW1 = m, SW2 = 100,

3)SW3 : It is to set up the distance from the starting point of Ticket to the point of black mark.
It is to set up the initial position of the first page,if the dip switch is the mode ‘First page No cut’.
You can set up the range 0~120 or 120~4000.
0~120 should be 0~15mm, if the cutting position is the forepart of black mark.
12~4000 should be 15~500mm, if the cutting position is the rearpart of the black mark.
Notice : The value ‘1’ means 0.125mm.
For example ) 300 x 0.125mm = 37.5mm
Notice : The factory mode is 1048(131mm), and is the black mark for the right side.
Notice : Please refer to 7.Ticket recommend.
Example)
Title Rev. Page
HMK(P)-081,HMC-081 Ver1.0
19
ABCD
[Front page,printing side]
0~15mm or 15~500mm
Starting point of black mark
Page 1.
Page 2.
Notice:Black mark for
the lef side, and rear
side.

2-9) Internal connector
1)CN1 : AC adapter Jack (AC00093-12-03,TECHWIN)
Pin Descript Remark
1 +24V
2 GND
3 N.C
You can make the choice one
of two, when you put the order.
2)CN1 : DC connector (YAW396-02,Yeonho)
Pin Descript. Remark
1 +24V
2 GND
※Alternative one : YH396-02,old Unlock type)
3)CN2 : (20017WS-03,Yeonho or 53014-0310,Molex)
Pin Descript. Remark
1 PR_A Presenter sensor power
2 PR_C Presenter dectection output
3 GND
4)CN3 : Power switch connector (YAW396-02,Yeonho)
Pin Descript. Remark
1 +24V +24V output voltage
2 +24V +24V input voltage
5)CN4 : Mechanism connector (SMW200-32C,Yeonho)
Pin No. Descript. Remark Pin No. Descript. Remark
1 +24V +24V 17 SI2 TPH Serial Input
2 GND GND 18 TH Thermoster
3 +24V +24V 19 +24V +24V
4 GND GND 20 GND GND
5 +24V +24V 21 CUT_A Cutter Control A
6 GND GND 22 CUT_B Cutter Control B
7 +24V +24V 23 HM_SW Cutter Home Switch
8 GND GND 24 Paper_A Paper sensor power
9 N.C 25 Paper_C Paper sensor signal
10 N.C 26 HD_UP Cover open signal
11 /LATCH TPH Latch 27 A Motor operation A
12 VDD +5V 28 B Motor operation B
13 /STROBE1 TPH STROBE1 29 /A Motor operation /A
14 /STROBE2 TPH STROBE2 30 /B Motor operation /B
15 CLOCK TPH CLOCK 31 MARK_A Blackmark sensor power
16 N.C 32 MARK_C Blackmark sensor signal
Title Rev. Page
HMK(P)-081,HMC-081 Ver1.0
20