Hyco Curve User manual

Product Instruction anual
Curve
CURVEW (white) & CURVEBSS (brushed stainless steel)
0.9kW Automatic Hand Dryer
Version 3.2 Jan 2015
V17.9/1

2
Thank you for purchasing a Hyco Curve hand dryer. Please ensure you read and
understand these instructions to ensure safe installation and operation. The Curve is
a modern, slimline hand dryer that is suitable for a variety of washroom applications.
This high speed, automatic hand dryer has a stylish and compact design specification
and can be the perfect option where space is restricted.
Key features
• 0.9 kW
• Sleek slimline design
• White / brushed stainless steel finish available
1. Im ortant safety oints
If the supply cord is damaged it must be replaced by the manufacturer,
its service agent or similarly qualified person in order to avoid electrocution
hazard.
Do not proceed with installation if there is any sign of damage to the product.
The product should only be connected to a supply that meets the specifications
detailed on the rating label.
Electrical installation must be carried out by a qualified electrician in accordance
with the latest edition of the IEE wiring regulations.
The appliance is not intended for use by persons (including young children)
with reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning the safe use of the appliance by a person responsible for their safety.
Children should be supervised to ensure they do not play with the appliance.
The appliance must be earthed.
The appliance is intended for drying hands only; it should not be used for any
other purpose.

3
2. Installation
To avoid malfunction do not install the appliance in the following environments:
Temperatures below -10 C or above 40 C.
Places in direct sunlight or strong light.
Within 40cm of any surface beneath the air outlet.
• When selecting a suitable location and surface for installation of the dryer,
consider the following:
• Water droplets will be blown from the hands and may land on surrounding
surfaces.
• Access for doors and people.
• Height of dryer positioning based on likely users (see table).
User Recommended mounting height
(bottom edge of dryer above finished floor)
ens 46”
Ladies 44”
Children 11-17 yrs 42”
Children 3-10 yrs 36”
Disabled 40”
• Ensure a horizontal and vertical level and then affix the supplied drilling template
and mark the holes ready for drilling.
Always ensure no concealed electrical wiring or pipework prior to drilling
into the surface.
• Drill the four x 8mm holes marked A-D on the supplied template.
• Insert the 4 x wall plugs into the holes.

• ake provision for the electrical wiring at this stage, the template details the
position for concealed wiring entry into the dryer.
• Using the supplied tool, remove the two security screws located at the base of
the dryer.
• Lift the cover away from the dryer by first pulling the cover down, to release
from the lugs located at the top, and then away from the main body of the dryer.
• Attach the dryer to the mounting surface by locating and tightening the four wall
plug screws supplied. The supplied washers and plastic collars should be fitted,
these provide anti-vibration to help reduce the noise to a minimum.
The product should only be connected to a supply that meets the specifications
detailed on the rating label.
The appliance must be earthed.
• Connection should be made to the fixed wiring of the property via a double pole
switched fused spur.
• Electrical connections should be made as follows:
Green/Yellow earth wire to the terminal marked “E” or
Brown/Red live wire to the terminal marked “L”
Blue/Black neutral wire to the terminal marked “N”
4
Recommended mounting height
(bottom edge of dryer above nished oor)
M 43”
L 41”
C 39”
C 33”
1

• If the electrical connection is surface mounted, ensure the cable is secured to the
body of the dryer using the supplied cable clamp and then exits the dryer via the
outlet at the bottom right corner of the dryer. Fit the supplied rubber grommet to
protect the cable from being damaged by the edges of the cover.
• Ensure the dryer is firmly attached to the mounting surface and then replace
the cover and secure using the two security screws and tool provided.
3. O eration
• Shake off excess water into the sink or basin.
• Place hands underneath the sensor to initiate operation.
• Slowly move hands back and forth to remove water droplets.
• Rub hands together firmly to remove any remaining residue.
• Repeat as necessary.
5

6
4. Dryer adjustments and Maintenance
Always disconnect the electrical power supply before commencing
maintenance or adjustment.
• It is possible to adjust both the sensing range of the dryer and the motor speed.
• Using a small cross headed screwdriver, locate the small blue and yellow cross
head screw components as shown below, via the two small holes beneath the air
outlet of the dryer. Clockwise will increase the settings and conversely anticlockwise
will reduce setting.
• The surface of the appliance should be wiped clean with a soft cloth and soapy
water. Do not use abrasive chemica s or c oths as damage may resu t.
• Periodically remove any fluff, dust or lint etc. from the inside of the dryer. To do this
first remove the cover and then, using a soft brush or vacuum cleaner, carefully
remove any debris that exists.
SPEED
SENSING DISTANCE
NO

7
5. S ecifications
CURVEW CURVEBSS
Vo tage/frequency 230V~/50Hz 230V~/50Hz
Power 0.9 kW 0.9 kW
Ingress Protection 24 24
Finish White Brushed Stain ess Stee
Weight 3.3kg 3.3kg
100mm
152mm
268mm

hyco.co.uk
Hyco anufacturing Ltd
Normandy Court
Express Way
Castleford, WF10 5NR
T 01924 225 200
F 01924 225 210
E [email protected]
INFOR ATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH THE
EUROPEAN DIRECTIVE 2002/96/E.
At the end of its working life this equipment must not be disposed of as household
waste. It must be taken to a local authority waste collection centre or to a dealer
providing this service. Disposing of electrical and electronic equipment separately
enables its components to be recovered and recycled to obtain significant savings in
energy and resources. In order to underline the duty to dispose of this equipment
separately, the product is marked with a crossed out dustbin.
7. Guarantee and service olicy
This product is covered by a standard parts or replacement warranty for a period of
three years from the date of purchase.
If there is a manufacturing defect within the warranty period we will send spare parts,
repair and return the unit or, at our discretion, supply a replacement product.
Incorrect installation and failure to follow correct operating instructions are excluded.
Consequential costs such as labour charges or damage to surroundings are expressly
excluded.
Contact us
If you experience a problem with this product you should first contact our service
department on 01924 225 200 before taking any further action. Experience has shown
that issues can often be resolved without the need to return or uninstall the product.