Hyco HURRICANE HD1600 User manual

HURRICANE
HAND DRYER
HD1600
Instruction M nu l VERSIO 1.1 OV 2007
6. GUARANTEE AND SERVICE POLICY
The Hyco Hurricane is supplied with a standard 12 month replacement
warranty (excluding Lamps) that protects against any manufacturing defects
for up to 1 year of the original purchase date. In the event of a product
failure please contact Hyco on 01977 517555. Incidental or consequential
damages are excluded from this warranty.
Hyco Manufacturing Ltd
California Drive
Castleford
WF10 5QH
Tel: [phone] Fax: [phone]
Web: www.hyco.co.uk
E-mail: [e-mail]
FYK0345 Hyco Hurr 1600 Man:FYK0345 Hyco Hurr 1600 Man 16/11/07 07:26 Page 1

HYCO HURRICANE HAND DRYER
HD1600
Th nk you for purch sing the Hyco Hurric ne H nd Dryer.
Ple se re d nd underst nd these instructions before
commencing inst ll tion, nd le ve them with the user when
inst ll tion is complete.
1. SAFETY
• The Electric l Inst ll tion must be c rried out by qu lified
electrici n in ccord nce with the current edition of the I.E.E.
Wiring Regul tions.
• Electrical connection must be made to the fixed wiring of the property
using a double pole isolating switch, with a break contact distance of at
least 3mm.
• This appliance must be grounded.
• The power cord should be connected following the colour coding below:
Brown: L
Blue:
Green / Yellow striped: E
• Only connect the Hand dryer to a single phase supply with a mains
voltage as specified on the rating plate.
• Do not cover the air inlet or outlet.
• The Hand dryer must be installed out of reach of persons using a bath or
shower.
3. OPERATION
• Shake excess water from hands.
• To activate the hand dryer, place your hands underneath the air outlet to
operate the sensor.
• Rub hands together lightly and rapidly.
• The dryer will stop automatically 1 second after removing hands.
• The dryer will automatically cut out after 1 minute of consecutive use.
• To re-start the hand dryer, put hands back underneath and re-operate the
sensor.
• The sensitivity of the sensor can be adjusted by removing the cover and
accessing the Printed Circuit Board (see fig 3)
Fig 3
Fig 2
Fig 1
2. INSTALLATION
• Please follow all safety instructions when installing the unit.
• Remove screws from the side of the cover as per Fig 1. Detach the
earth wire from the base carefully.
• Drill 4 holes of 8mm diameter following Fig 2 below (note that the
entry for the power cord is located at the right hand side, 3.5 cm
above the bottom right mounting hole).
• The unit must be mounted at least 40cm above any surface and a
minimum space of 18cm between the sides of the unit and any other
surface.
• Insert the power cord and connect as specified following the safety
instructions.
• Re-attach the earth wire in the frame and replace the cover.
• Once the Hand dryer is installed correctly, switch on the power.
18cm Min
Resistor
changes
sensitivity
Please adjust
carefully
16.6cm
22.6cm
18cm
Wire
entrance
3.5cm
40cm Min
4. CLEANING AND MAINTENANCE
• Wipe clean using a soft, damp cloth.
5. SPECIFICATIONS
• Voltage: 230v-50Hz
• Rated Power: 1600W
• Current: 6.9A
• IP Rating: IPX1
• Weight: 3.85kg
• Adjustable IR Sensor sensitivity
Schematic diagram
268mm 10.6"
206mm
8.1"
150mm 6"
FYK0345 Hyco Hurr 1600 Man:FYK0345 Hyco Hurr 1600 Man 16/11/07 07:26 Page 4