HydraBeauty SPA08 User manual

IMPORTANT: before starting the equipment correctly, please follow the
installation instructions. Any damages caused by incorrect operations will void
the warranty.
Safety Information:
Thank you for choosing our products! This user instruction is specially designed for
the safety of you and others. Please read the instructions carefully before installing or
using the machine and follow them when using.
Electrical Safety
11 in 1 HydraFacial skin rejuvenation device
SPA08 User Manual

Before installing the machine, make sure that your local electric network complies
with the voltage and frequency indicated on the tag on the rear panel. Otherwise, the
machine may be damaged incase of excessive current or voltage rise.
Never touch the machine with damp or wet hands or feet.
It is dangerous to change or try to modify the function of this machine in anyway.
Do not attempt to operate this unit if the power cord has been frayed or broken
Do not spill water or other liquids into or onto your unit.
During long periods of non-use, disconnect the unit’s main power.
Safety Rules When Installing
Place the machine on a stable and secure base. It should not be subjected to any jolts
or vibrations.
Never expose the unit to too high(>40ºC) nor too low temperature(<5ºC).
NEVER EXPOSE THE UNIT TO RAIN OR ANY OTHER HUMIDITY.
Do not expose the unit to direct sunshine or install the unit close to a source of
heat(central heating, radiator…); otherwise the screen may be damaged.
Do not cover or block the ventil at or behind the unit.
Safety Rules When in Use
Well clean areas to treat before treatment.
Never touch the machine with damp or wet hands or feet.
Never place the cavitation handpiece on the liver, kidney area.
Operate Interface Instruction
Treatment screen interface.
Make sure the power line has been installed correctly; make sure the hand pieces are
well connected with the equipment; ensure the circuit breaker (if any) at the back of
the machine is pressed to “on”. The working menu will appear automatically. Choose
the Language. Choose the right parameter to do the treatment according to the needs
of customer.
Turn on the machine and you can see the welcome screen and main selection
interface.

1 . Instrument introduction
1.Hydrodermabrasion handle
2. Diamond dermabrasion handle
3. Ultrasound working handle
4. Three-polar RF handle
5. High Frequency handle
6. Skin scrubber
8. Spray mist gun
9. Photon brush（4 pieces）
10. 15 inch touch screen
11. Vacuum control knob
12. Water level knob
13.Power button switch
*Before operating the machine, please check the connections. Then turn on and off the
machine for 3 to 5 times. Then keep the machine running for 5 minutes to check the stability
of the machine.
14.Monitor connection pug
15.Waste bottle
16.filter
17.Power socket
18.Power switch

2 . Introduction of the Function
(1) Hydrodermabrasion
Hydradermabrasion– the latest in skin care technology. Hydradermabrasion utilizes the
natural healing powers of water and oxygen to effort lessly exfoliate the skin without
the use of hard crystals or abrasive textured wands, generating deeply hydrated and
healthier looking skin.
。
Application:
Rejuvenate sun damaged skin-face, neck, shoulders, back, arms and legs.
Reduce age spots.
Minimize of blotchy skin coloring.
Reduce acne and superficial scars from past injury.
Remove blackheads and whiteheads.
Reduce oily skin.
Improve overall skin health.

1 . click set working time ，1-60mins ；
2、choose bottle A/ B/ C/ D，
3、click start operating ，stop operating ，
4. When the set working time is up, the instrument will automatically pause,
5. Clean and disinfect the used working head.
Note: Please clean your face before use.
The suction and water flow can be adjusted through the two knobs on the front of the
instrument.
(2) Spray gun operation interface
The nano-oxygen gun (deep water replenishment) sprays oxygen with nano-particles,
and the water particles are fine, directly penetrating the bottom of the muscle, which
is dozens of times the effect of ordinary spray. Atomized products, promote
absorption, replenish water and oxygen.

1. Pour the nutrient water into the small cup of the oxygen spray gun, the amount of
water is about 2/3 of the cup, and then cover the lid. The small cup of the oxygen
spray gun can only contain low-concentration non-sticky products. Products in other
states are likely to cause pinholes to block.
1. click set working time ，about 15-20mins，
3、click start operating ，stop operating 。
Note: Clean the small cups and pipes in the sprayer after each use to avoid clogging.
Cautions:
①The product should be liquid when using oxygen sprayer.
②Avoid spraying into mouth or nose when spraying oxygen.
③Clean the small cup and the pipe inside the sprayer every time use it, to avid jam.
Clean method:
Pour the purified water into the small cup, and press the control button and then
pullback towards.
Supply nutrients and moisture for the skin rapidly, smooth skin, lightening stains,
improve chlorosis, dull conditions, make skin rosy, white, transparent, tender,
tightening indeed, with special spa oils will be better.
(2) Three-pole radio frequency operation interface
(3)
The radio frequency wave penetrates the barrier of the epidermal basal melanocytes to
heat the collagen fibers of the dermis to 55°C-65°C, and the collagen fibers shrink, so
that the loose skin wrinkles are tightened, so as to achieve the purpose of beauty and
wrinkle removal.

1、click choose mode ，adjust intensity ，
2、click set working time ，facial treatment time about 20-30mins，
3、Apply gel to the care area, and move the electrode probe from the inside to the
outside, from the bottom to the top. If there is less fat in the eyes and forehead, the
energy output intensity should be appropriately reduced.
4、click start operating ，stop operating，
5. When the set working time is up, the instrument will automatically pause.
6. Clean the skin with warm water,
7. Clean and disinfect the used radio frequency work head.
Precautions:
1. The beautician should wear knotted gloves when operating.
2. The electrode probe must be in full contact with the skin.
3. The electrode probe is close to the skin to move slowly, not stop moving.

(4) High Frequency
High frequency is through the high frequency electricity rate coagulation, urges the
eqidermal cell necrosis, which can in instantaneous thoroughly eliminate all kinds of
spot both on the face and on skin surface, such as old age spots, freckles, granules,
tattoos, moles, etc. The effect is obvious with no bleeding or scar leff.
1、click set working time ；
2、click adjust intensity ；
3、click start operating，stop operating 。
Operation steps:
①Indirect Method:
Please screw in the glass tube in the hand piece.
Please ask the client to hold the glass tube after touch some talcum powder.
Turn on the machine and the electricity will get through from hands to the
whole body.
Beauticians do the massage on client’s face from neck to chin and from visor
to forehead.
Please adjust the intensity to “0”. Make sure that the machine is turned off
and puck the glass tube out of the hand piece.
This method is fit for dry nature skin and aged skin.

②Direct Method:
Please grease essence and cream on the face first and then the beautician
holds the metal bar to put the glass tube on client’s face. Turn on the
machine.
Massage with the glass tube like “Z” or helix on client’s face, do the
treatment as follows, forehead → nose → right side of the face → chin →
left side of the face → nose → forehead.
Please adjust the intensity to “0”. Make sure that the machine is turned off
and puck the glass tube out of the hand piece.
This method is fit for greasy nature skin.
③Sparkle Method:
Cover client’s eyes with a piece of the wet cloth patch and touch the face
with the glass tube on the part of inflammation. For one time, the treatment
should be less than 10 seconds
It’s normal if there are sparkles come out while the glass tube touches the
face.
Please adjust the intensity to “0”. Make sure that the machine is turned off
and puck the glass tube out of the hand piece.
This method is fit skin with sore, inflammation and wounds
④Hair Care Method:
Use the comb tube together with pilatory.
Toward the direction of the hair to move the comb tube.
Please adjust the intensity to “0”. Make sure that the machine is turned off
and puck the glass tube out of the hand piece.
This method is for stimulating the skin surface, reducing folliculitis and
improving the healthy growing of the hair.
Cautions:
①For sensitive skin, please cover a piece of voile to avoid the excess stimulation.
②Do not place on one part over 10 seconds.
③Pregnant women and people with pacemaker are unfit for this treatment.
④Please make sure that install the glass tube into the hand piece before turning on
the machine. Adjust the intensity to “0” after finish.
⑤Skin with freckle and splash is unfit for this treatmen

(5) Ultrasound
Ultrasonic, with the frequency of 1-3 million times per second, with the process to be
transmitted to the body, is absorbed by epidermis dermis subcutaneous tissue, the
absorption of ultrasonic waves is converted into thermal energy, thermal effects of
ultrasound, the living tissue temperature increased slightly 0.5-1 ℃, promote capillary
function and fine inter cellular lymph flow, helps transport nutrients to the cells needed
for blood vessels, promote metabolism and to assist the flow of lymph, maintain
healthy skin. Maintain skin elasticity/ break down fat and prevent obesity. 1 million
vibrations per second ultrasound, when the wave is transferred to the organization,
with the ultrasonic vibrations stimulate biological tissue and skin tissue, relieve tension,
to maintain skin elasticity. Heated generated by vibration can make it easier to break
down fat and help prevent obesity.
Application:
*Melts fat and cellulitis cell, maintain skin texture smooth
*Massage effect: helps to produce collagen and elastin, activates the fibroblast and
enhances skin elasticity
1、click choose mode ，click adjust intensity ，
2、click set working time，facial treatment time about 20-30mins，