Hydro Crunch 6 INCH 2 SPEED CLIP FAN User manual

IMPORTANT!
Do not dispose product or any other part of it as unsorted municipal waste –
instead it shall be handed over to the applicable collection point for the recycling of electrical
and electronic equipment.
The following pages contain important safety and operating instructions. Please
read and follow all instruction in this manual. Carefully read and review all safety
instructions, warnings and cautions contained in this manual. Failure to read and
follow these instructions, warnings and cautionary statements may result in severe
injury or death to persons and pets or damage to personal property.
INSTRUCTION MANUAL
6 INCH 2 SPEED CLIP FAN
READ AND SAVE THESE INSTRUCTIONS
IMPORTANT SAFEGUARD INSTRUCTIONS

WARNING:
When using electrical appliances, basic precautions should always be followed to
reduce the risk of fire, electrical shock and injury to persons, including the
following:
1. Make certain the power source conforms to the electrical requirements of the Fan.
2. Make certain that the room is equipped with a working smoke detector.
3. Use this Fan only as described in this manual. Any other use not recommended by the
manufacturer may cause fire, electrical shock, or injury to persons.
4. To reduce the risk of personal injury and electric shock, the Fan should not be played with
or placed where small children can reach it.
5. Unplug power cord before installing, servicing, or moving the Fan.
DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE MEANS OF
DISCONNECTING POWER WHEN SERVICING OR MOVING THE FAN. ALWAYS
UNPLUG THE POWER CORD. ALWAYS TURN OFF AND UNPLUG FAN BEFORE
LEAVING THE AREA. NEVER LEAVE CHILDREN UNATTENDED WHEN THE FAN IS
ON OR PLUGGED IN.
6. This Fan must NOT be used in potentially dangerous locations such as flammable, explosive,
chemical-laden or wet atmospheres where gasoline, paint or flammable liquids are used or
stored.
7. DO NOT use Fan in or near a window. Rain may create an electrical hazard.
8. Completely assemble Fan, according to instructions, before connecting to power supply.
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of
electric shock, this plug is intended to fit in a polarized outlet only one way. Match wide
blade of plug to wide slot. Fully insert. If the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician. DO NOT attempt to defeat this
safety feature. This plug is a safety feature, to reduce the risk of fire, electric shock and
personal injury. DO NOT remove, replace, repair or tamper with the originally supplied plug.
9. Where possible, avoid the use of extension cords because the extension cord may overheat
and cause a fire. If you must use an extension cord, minimize the risk of overheating by using
the shortest cord possible and ensuring that it is UL listed. NEVER use a single extension cord to
operate more than one Fan. Do not plug Fan into any other cord connected device, such as a
power strip, cord reel, surge protector, multiple outlet adapters or outlet-type air fresheners.
1 Year Limited Warranty Service
If the product will not work after you have read the troubleshooting guide and practiced the troubleshooting
options, you are advised to return the Hydro Crunch™ product to the retailer you purchased it from. The dealer
will be able to examine the product and test its components. If they are not able to repair the product, they will
return it to us for examination and repair/replacement. Do not attempt to repair any product on your own, as
serious injury or death may result. If the retailer is not able to help you and the product is still under
manufacturer’s warranty, you may contact us for technical support. In some cases, you will be issued an RMA#
(return merchandise authorization number) to return the unit for factory repair. Complete the warranty form below
and return the product with all original packaging, your receipt of purchase, and a valid RMA# to the address
below. Please pack and ship the product in its original packaging. If it is damaged in shipment we cannot be
responsible and the warranty may be voided. Once we receive RMA package, it will be repaired or replaced and
shipped back to you. Please note if an additional warranty was purchased and include the extended warranty
sales receipt with your return.
RETURN FORM
Include the following if returning:
 Proof of purchase
 This completed form
 RMA# on the outside of the box
 Extended warranty receipt
Return Merchandise Authorization Number (Required): _______________________________________
Contact Name: _________________________________________________________________________
Address: ______________________________________________________________________________
Phone #: ______________________________________________________________________________
Email Address: _________________________________________________________________________
Please give a brief description of your technical issue: ________________________________________
_______________________________________________________________________________________
SEND TO:
Hydro Crunch
20651 Golden Spring Drive Suite 115
Walnut, CA 91789
714-516-8176

MAIN SPECIFICATIONS
Rated Voltage: 120V
Rated Frequency: 60Hz
Rated Power: 15W
DISPOSAL
Do not dispose product or any other part of it as unsorted municipal waste – instead it shall be
handed over to the applicable collection point for the recycling of electrical and electronic
equipment.
The use of such devices may create a fire hazard.
10. NEVER operate any Fan with a damaged cord or plug or after the Fan malfunctions, has
been dropped or damaged in any manner. There are no user serviceable parts. Return Fan to an
authorized service facility for examination, electrical or mechanical adjustment or repair.
11. NEVER insert or allow fingers or foreign objects to enter any ventilation or exhaust opening
as it may cause an electric shock or fire, or damage the Fan. To reduce the risk of fire, DO NOT
block or tamper with the Fan in any manner while it is in operation.
12. Locate the Power Cord so the Fan or other objects are not resting on it. DO NOT run Power
Cord under carpeting. DO NOT cover Power Cord with throw rugs, runners or the like. Arrange
Power Cord away from room traffic and where it will not be tripped over.
13. This Fan is not intended for use in wet or damp locations. Never locate a Fan where it may
fall into a bathtub or other water container. NEVER use Fan where flammable liquids are used
or stored.
14. NEVER use Fan outdoors.
15. This Fan is not suitable for use in agricultural facilities including areas where livestock,
poultry or other animals are confined.
16. This Fan is not suitable for use in hazardous locations.
WARNING
REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK - DO NOT USE THIS FAN
WITH ANY SOLID STATE SPEED CONTROL DEVICES.
READ AND SAVE THESE INSTRUCTIONS

PARTS DIAGRAM
1 Front Guard
2 Fan Blade
3 Rear Guard
4 Motor Housing
5 Speed Control Switch
6 Pivot Screw
7 Power Cord
8 Clip
FUNCTION
2-Speed settings
Multi-directional airflow
ASSEMBLY
Check to see that you have received all the following
parts.
Fan Head Assembly:
Insert the FAN HEAD into the top of the CLIP until
fully seated and tighten the FAN ANGLE ADJUSTMENT
(see Fig.2)
OPERATING INSTRUCTIONS
1. Plug into any standard 120V AC, 60 Hz outlet.
2. Clip the Fan to a flat structure that is between 1/4" and 1-3/4“ thick or a pole
1/2" to 1-3\4" diameter. Clipping the Fan to structures with greater or lesser
widths may lead to instability.
3. TO CONTROL THE FAN SPEED: Turn the Knob at the rear of the Motor Cover.
Speed-1---Low
Speed-2---High
Speed-0---Off
4. The fan can be adjusted through 360 degrees on its central pillar (see fig 5)
5. The fan can be adjusted through 45 degrees vertically (see fig 4)
6. The fan can be clipped to flat boards (see fig 3)
TO ADJUST HEAD ANGLE: Loosen Knob under Fan Head. Tilt head to desired air flow
position. Retighten Knob.
MAINTENANCE & STORAGE
To reduce the risk of electrical shock and fire please observe the following instructions:
- Always unplug the cord before moving, servicing or cleaning.
- Never place the Fan in or near water.
-TO CLEAN: UNPLUG FAN! Do not immerse electrical parts in water! Use a soft cloth
moistened with mild soap and water solution to clean plastic parts. Wipe off any soap
residue. DRY ALL PARTS COMPLETELY BEFORE REASSEMBLING AND RECONNECTING TO
POWER SUPPLY.
-NEVER use ALCOHOL or SOLVENTS such as gasoline, benzene, paint thinner, or other
harsh cleaners.
-Store the Fan with these instructions, in the original carton in a cool, dry place.
TROUBLE SHOOTING
1. If you experience any problem with your fan, please return it to its supplier, don’t attempt to
open the motor housing or any other sealed components.
2. Check your electric cord for wear and tear, if it is damaged, it must be replaced by a
qualified electrician it is strongly advised that you do not operate your fan if the electrical
cord is damaged.