Hydrogen For Health HX900 User manual

HX900
Hydrogen Inhaler
Instruction Manual

What is Molecular Hydrogen ? Working Principle
.
.
Information source: http://www.molecularhydrogeninstitute.com/

1. Product Show . Operating Instruction
Water Inlet
Gas Outlets
Water Level
Showcase
Operation Panel
2
Open the water tank lid counterclockwise, fill in 1L pure or
distilled water (mineral and tap water are strictly prohibited),
and close the lid clockwise after filling the water.
1
21 Continuous Mode & Sleep Mode:
Remove the O2 and H2 output caps.
Install each of the 2 humidification bottles
on the machine (see the picture on the
right). Then connect each of the 2 ports
on one end of the tee tube to the left
humidification bottle, and insert the other
end of the tee tube from above to the
port of the right humidification bottle.
Connect the nasal cannula to the
humidification bottle on the right side..
2 Pulse Mode: Insert the nasal breathing tube directly into the H2 port. (No
need to install the humidification bottles under this mode)
RR bpm

Connect the power supply, the display will automatically turn on.
The power interface is on the back of the machine near bottom.
3
Touch the corresponding buttons to
set time, mode, and flow.
4
Mode selection
Touch the continuous mode button,
the machine starts working and
outputs hydrogen continuously.
This mode is suitable for making
hydrogen-rich water too.
Continuous Mode
5
How to connect the hydrogen diffusion stone to this unit and
make hydrogen water?
Directly connect the cannula to H2 outlet, and put another side of h2
diffusion stone into the drinkable water, then start continuous mode to
make hydrogen water (Please do not use humidification bottle under
this function)
Power Interface

RR bpm
RR bpm

3. Operating Notice:
The pattern of water shortage in the water tank appears on the screen,
indicating that the water tank is short of water. Please add pure water to
the water tank in time. It is recommended that the amount of water added
should not exceed 1L.
Water shortage
When the temperature is overheat, an overheating pattern will appear on
the screen. In this condition, please check whether the water level in the
water tank is too low, and wait for the machine to cool down before using
it again. In case of unknown reasons, please contact the distributor.
Overheat
TDS appears on the screen, indicating that the water in the water tank is
impure, please pour pure water (TDS<5) into the water tank again.
TDS
When the filter icon appears on the screen, please replace the filter in time.
Filter
The water in the tank should be replaced every 2 weeks.
Drainage and water change:
First cut off the power, then open the drain of the machine, drain the water
in the tank, and then the drain cover tightly, add new water, clean the tank
(after adding a small amount of new water, and cover the tank, gently
shake to clean), pour off the water in the tank, pour fresh pure water into
the tank.
Steps:
Pulse Mode
Insert the nasal breathing tube directly into the H2 port, touch the pulse
mode button, the machine will automatically release the pressure to
release the gas and make a popping sound, at the same time the machine
will make a popping sound when it sensed your breathing:
If the breathing is very weak, the sensor can not monitor the pressure
difference, so the stored gas will not come out, only when the breathing is
stronger can monitor the pressure difference and the machine works
normally.
In the pulse mode, the screen will display the respiratory symbol.
Sleep Mode
Touch the sleep mode button, the machine works normally and produces
hydrogen, the screen enters the sleep state, touch the button again, the
screen returns to the normal state.

. Cautions
Cautions
1. Please use the machine in a ventilated environment
2. Do not tilt this product during use
3. Please add pure water or distilled water only
4. No open flames are allowed near the machine during use
5. Please drain the water when the equipment is transported or out of use
4. 5. Specifications
Product name Hydrogen oxygen inhaler
Model No. SG-450 SG-600 SG-900
Voltage 110V~240V
Power <350W
Working time 1hour~6hours
Product size 185mm*218mm*248mm
Product weight Around 4.5KG
Carton size 302mm*262mm*395mm
Gross weight Around 5.5kg

1. The warranty period is one year from the date of purchase.
2. During the warranty period, the machine should be replaced with the
proof of purchase and warranty card. If the normal spare parts are replaced,
the user should pay for the spare parts.
3. Problems caused by incorrect operation or self-disassembly during the
warranty period are not covered by the warranty, but paid service is available.
6. PackageIncluded 7. Warranty Rules
Name Quantity Picture
Hydrogen oxygen inhaler 1 Unit
User manual 1 Booklet or E file
Nasal cannula 1 Piece
Tee Tube 1 piece+3pieces
Humidification bottle 2 Sets
Power supply 1 Piece
Warranty Card
Problem description
Purchase date
Customer name
Telephone & Phone
Email
Customer address