Hyperkin SCOUT PREMIUM User manual

INSTRUCTION MANUAL
www.HYPERKIN.com
© 2019 Hyperkin Inc. Hyperkin® is a registered trademark of Hyperkin Inc. Super NES® is a
registered trademark of Nintendo® of America Inc. Bluetooth® is a registered trademark of
Bluetooth Sig, Inc. This product is not designed, manufactured, sponsored, endorsed, or
licensed by Nintendo® of America Inc. nor Bluetooth Sig, Inc. in the United States and/or
other countries. All rights reserved. Patent Pending. Made in China.
PREMIUM
WIRELESS BT CONTROLLER
SCOUT
PREMIUM
WIRELESS BT CONTROLLER
SCOUT

BEFORE YOU BEGIN
• The CONTROLLER SYNC BUTTON is located on the very top of the Scout near
the MICRO CHARGE PORT.
• The CONTROLLER LED INDICATOR is located on the face of the Scout near
the top.
• The DONGLE LED INDICATOR is located on the front of the DONGLE.
• The DONGLE SYNC BUTTON is located on the front of the DONGLE.
• The MICRO CHARGE PORT is located on the very top of the Scout.
SYNCING THE SCOUT
1. Connect the DONGLE to your SNES.
2. Press the CONTROLLER SYNC BUTTON once to begin syncing the Scout.
3. The CONTROLLER LED INDICATOR will quickly ash BLUE, then light up solid
BLUE when the Scout is fully synced. If the Scout is not synced, the
CONTROLLER LED INDICATOR will slowly ash BLUE. Pairing will take
about 5-10 seconds.
ONCE YOU'VE SYNCED
• Pressing the CONTROLLER SYNC BUTTON will turn OFF the Scout.
• Holding the CONTROLLER SYNC BUTTON for 2 seconds will turn ON the
Scout.
• Pressing ANY BUTTON or the D-PAD will WAKE UP the Scout if it has gone to
sleep.
CHARGE CABLEDONGLECONTROLLER
CONTROLLER
DONGLE
CONTENTS
CONTROLLER SYNC BUTTONCONTROLLER LED INDICATOR
D-PAD
DONGLE SYNC BUTTON DONGLE LED INDICATOR
MICRO CHARGE PORT
SELECT BUTTON START BUTTON

CHARGING YOUR SCOUT
1. Connect the provided MICRO CHARGE CABLE to your Scout. Connect the
other end to a USB power source.
2. A solid RED light on the CONTROLLER LED INDICATOR indicates the Scout is
charging.
3. The RED light will turn off when the Scout is fully charged.
Note: You can use the Scout even while it is charging.
4. A slowly ashing RED light on the CONTROLLER LED INDICATOR means the
Scout is low on battery.
HELPFUL HINTS
• The Scout can operate up to about 30 feet from your SNES console.
• After 5 minutes of no activity, the Scout will go to SLEEP.
• If the Scout is ON and not synced, the CONTROLLER LED INDICATOR will slowly
ash BLUE for 20 seconds, then go to SLEEP.
• When the DONGLE is connected to your SNES console, pushing the DONGLE
SYNC BUTTON will cause the DONGLE LED INDICATOR to ash BLUE.
• The Scout will automatically connect after the initial syncing.
CONNECTING TO A BT DEVICE
(NO DONGLE REQUIRED)
When connecting to a BT-compatible device such as a computer or
smartphone, the controller will show up as “Input device (keyboard, mouse,
etc.)” while pairing. Once paired, the controller will be listed as “Hyperkin Pad.”
Setup and functionality may vary depending on your device.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate equipment.
This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference in radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
FCC Warning Statement
Statement of Compliance with EU Directive
Hyperkin Inc., located at 1939 West Mission Blvd, Pomona, CA 91766, declares under our sole responsibility
that the product, Hyperkin "Scout" Premium Wireless BT Controller, is in compliance with the essential
requirements and other relevant provisions of Low Voltage Directive (LVD) 2014/35/EU, EMC Directive
2014/30/EU, and RoHS Directive 2011/65/EU and carries the CE marking.
The full Declaration of Conformity can be requested by emailing:
Email: [e-mail]
Company Name: Hyperkin Inc.
Address: 1939 West Mission Blvd, Pomona, CA 91766