HypoTheory affluent HTDF366NG Installation guide

1
USE,CARE & INSTALLATION MANUAL
HypoTheory Affluent Series: Pro Style Ranges
HTDF366NG/HTDF366LP

2
HypoTheory Affluent Series: Pro-Style Ranges
www.hypotheory.com
Customer Care
The model and serial number are printed on
the bac of the product or the product box.
For warranty purposes, you will also need
the date of installation and name of your
licensed plumber or electrician. Record this
information below for future reference.
If your product ever needs repairs after
product installation, be sure to use a
HypoTheory experienced service provider
recommended by our customer care center
by calling 800-928-4693 x 2
Important Note: To ensure this product is
installed and operated as safely and
efficiently as possible, ta e note of the
following types of highlighted information
throughout this guide.
Please fill out the service information form
on the right side of this page.
IMPORTANT NOTE highlights information
that is especially important.
WARNING states a hazard that may cause
serious injury or death if precautions are not
followed.
CAUTION indicates a situation where minor
injury or product damage may occur if
instructions are not followed.
Table of Contents
Registration Information
Serial Number
Date of Purchase
Installer Name
Installer Number
Authorized Dealer
Dealer Number
Model Number
Safety Precautions Pages 4-7
Specif ications Pages 17-23
Installation Pages 9-16
List of parts &
accessories included.
Pages 31
Care & Cleaning Page 8
Wiring Diagram Page 30
Troubleshooting Pages 24-29
Warranty Information Pages 32-25

3
HypoTheory Affluent Series: Pro-Style Ranges
www.hypotheory.com
Thank You
Than you for your purchase. We loo
forward to being part of your estate for
decades! With the proper care and
maintenance our appliances have a
reputation of lasting a very long time. Our
customer's satisfaction & support are what
allow us to instill the legacy our pioneers
have set. To offer longevity, beauty &
quality all in one, and ensure we truly do
stay simply above the rest.
HypoTheory was established in 1960, in
Wandsworth, London by Hymsley Politz,
Diana Politz & Theodore Waldorf . Their
once successful 3 decade old restaurant
chains were not progressing; due to slow
service resulting from outdated coo ing
appliances. They were in need of new
itchen appliances to compete with they're
competitors & stay in business. Mr. Politz
put a call into a well nown steel factory in
Murano, Italy. They required the steel
factory to design all of their appliances by
hand and requested that they only obtain
the best of internal and external
components. Several months later some of
the most extravagant & energy efficient;
high end quality sets of ovens & ranges
arrived.
With your purchase, you receive one of the
strongest two year warranties in the
appliance industry with the flexibility of
extending for an additional five years for an
nominal fee. Ta e a moment to read the full
warranty statement. It’s also important to
register your HypoTheory appliance in the
unli ely event that service becomes
necessary during the warranty period, and
a proof of purchase(invoice) record in case
of a claim will be required. You may register
by doing the following:
Register online at hypotheory.com by
clic ing “Product registration”.
As a HypoTheory owner, you can count on
royal treatment & support around the cloc .
Our customer care center is available 24
hours a day, seven days a wee and
staffed by nowledgeable product experts
at our sales & customer service center in
Manhattan, New Yor .
We are confident this guide will answer
your questions about the features,
operation, and maintenance of your
HypoTheory appliance, but if you have
additional questions, please contact us at
800-928-4693 or visit us online at
hypotheory.com.

4
Safety Precautions/Instructions
www.hypotheory.com
GENERAL SAFETY REQUIREMENTS
Please read all safety instructions before
using this appliance.
●Do not clean the range gas et,
because rubbing or moving the
gas et may eliminate the required
tight door seal.
●Do not wear loose or hanging apparel
while using the range.
●Do not touch heating elements or
interior surfaces of the range. Heating
elements may be hot even though
they are dar in color. Interiors of the
range become hot enough to cause
burns. During and after use, do not
touch, or let clothing or other
flammable materials come in contact
with the heating elements or interior
surfaces of the range until they have
had sufficient time to cool. Other
surfaces of the range may become
hot enough to cause burns. These
surfaces include the range door,
window, range vent and the surface
near the range vent.
●Do not store items of interest to
children above the range, as they
could climb on the appliance to reach
items and be injured.
●After removing the appliance from its
pac aging, ma e sure your appliance
has all of its parts, and is in good
order.
●The pac ing material (plastic bags,
poly foam,nails,metal strips,etc.) must
be moved away from the reach of
children.
●Do not attempt to alter the technical
features of the appliance without the
permission of HypoTheory
Corporation- or your warranty may be
voided.
●Ma e sure there is a ventilation
system available to duct/remove the
moist air/coo ing debris away. Any
name brand ventilation system could
be compatible, it does not have to
bear the HypoTheory logo, the only
requirement is the ventilation motor
produces a minimum of 300 CFM.
You may review the diagram in the
manual for distance requirements.
●Do not touch the appliance with
wet/damp hands or feet.
●Do not allow the appliance to be
operated by children/disabled without
supervision.

5
GENERAL SAFETY REQUIREMENTS
Please read all safety instructions before
using this appliance.
●Use the range only for coo ing tas s
expected of a residential/home range
as outlined in this guide. Not for
commercial purposes.
●Before using the self-clean feature,
remove broiler grill and pan, range
rac s, range rac guides and any
other utensils.
●Do not use commercial range
cleaners or range liner protective
coatings, such as aluminum foil, on
any part of the range.
●Do not use water on grease fires.
Smother any flames with a lid, ba ing
sheet or flat tray. Flaming grease can
be extinguished with ba ing soda or a
multipurpose chemical or foam
extinguisher.
●Do not heat unopened food
containers as they could burst and
cause injury.
●Do not store combustible, flammable
or explosive materials in the range or
adjacent cabinets.
●Do not place coo ware on the floor of
the range.
●Do not repair or replace any part of
the range unless specifically
recommended in literature
accompany- ing this appliance. All
service should be referred to Wolf
factory certified service.
●Do not use range for warming or
heating a room.
●Do not leave children alone or
unattended in the area where the
range is in use. Never allow children
to sit or stand on any part of the
range. Do not let children play with
the range.
●Do not use abrasive or caustic
cleaners or deter- gents on this
appliance as these may cause
permanent damage. Do not use
aerosol cleaners as these may be
flammable or cause corrosion of
metal parts.
●The size of a flame does not
necessarily determine the burner
input, it is the proper distribution of
the flame, that dictates the BTU. That
is why it is important gas/propane
pressures are within the average 6” or
7” water column for natural gas, and
11” water column for propane.
Safety Precautions/Instructions
www.hypotheory.com

6
GENERAL SAFETY REQUIREMENTS
Please read all safety instructions before
using this appliance.
●Ensure proper installation and
servicing to avoid voiding the product
warranty for improper installation.
This appliance must be properly
installed and grounded by a licensed
plumber or licensed electrician.
●This appliance must be
repaired/serviced by a qualified
service technician- available through
our nationwide service networ s of
professionals. Please call technical
support at 800-928-4693 x 2 if you
are in need of a repair after the
product has been properly installed
by a licensed plumber or electrician.
●Read this use & care guide carefully
before using your new range to
reduce the ris of fire, electric shoc
or injury.
●Warranty service must be performed
by a qualified licensed appliance
technician: that has had experience
wor ing on HypoTheory appliances.
●Have the installer show you where
the fuse or electrical box is located in
your home. Learn how and where to
shut off the electricity to the range.
●Always properly clean and maintain
the range as recommended in this
guide. Clean only those parts listed in
this guide. Do not use any rough
object (Brillo pad, etc. to clean
delicate metals to avoid damage).
●Do not place coo ware on range floor
or use aluminum foil or other material
to line the range floor or side walls.
Failure to adhere to this notice will
damage the range and will void your
warranty.
●Always use dry pot holders when
removing pans from the range. Wet or
damp pot holders can cause steam
burns. Do not let pot holders touch
hot heating elements. Do not use a
towel or other bul y cloth.
●Be sure that the range cool air inta e
(located above the door) and range
exhaust vent (located below the door)
are unobstructed at all times.
●Position range rac s in desired
locations when range is cool. If a rac
must be repositioned after the range
is already hot, be certain pot holder
does not contact a hot heating
element in the range.
Safety Precautions/Instructions
www.hypotheory.com

7
GENERAL SAFETY REQUIREMENTS
Please read all safety instructions before
using this appliance.
●The appliance must be solely used for
coo ing food and not for any other
purpose, such as heating a room,etc.
Is dangerous and prohibited, and will
void all warranties.
●Disconnect the appliance from the
electrical supply before carrying out
any cleaning or maintenance.
●Never try to remove the plug from the
main supply soc et by pulling the
cable. You should turn off the
brea er/fuse first.
●Do not allow children to approach the
range while it is in use, to avoid
burning.
●If the appliance malfunctions or does
not wor properly, switch it off and do
not use it, until it is repaired. All
repairs should be performed by a
licensed appliance technician that has
or must be approved by HypoTheory
Corporation. All spare parts will be
provided at cost unless under
warranty. You may contact our
technical support department to order
parts or obtain service at 800-928-
4693 x 2.
●After using the appliance you must
turn all of the nobs to the OFF
position.
●Ensure a licensed plumber chec s
the gas regulation and ensures the
burner flames are consistent and at
their optimal performance.
●Please read the trouble shooting
section of your manual before you
call. If this is a pre-product
installation, please ensure your
licensed plumber or electrician
contacts technical support during
normal business hours, it is against
company policy to consult consumers
on installation questions, because of
liability (sorry).
●All HypoTheory gas appliances must
be installed by a licensed plumber. All
HypoTheory 220 volt based electrical
appliances/ or appliances that require
wiring configuration must be installed
by a licensed electrician. All dual fuel
appliances must be installed by a
licensed plumber, and a licensed
electrician. At the purchaser's
expense.
●Please ensure the range legs are
secure.
●The range cleaning function should
last no longer than 4 hours.
Safety Precautions/Instructions
www.hypotheory.com

8
Care & Cleaning Instructions
www.hypotheory.com
How To Clean Your Range prior to the
self-clean cycle (recommended not
required).
Please read all cleaning instructions before
using this appliance.
Instructions
●Remove the oven racks: Remove
your oven racks, and anything else
you have inside the oven. Distribute
aside.
●Mix baking soda: In a bowl, mix a 1/2
cup of baking soda with a few
tablespoons of water. Adjust the ratio
of both as needed until you have a
spreadable paste.
●Coat your oven, cast iron pan
supports, griddle & all other cast iron
accessories: Spread the paste all
over the interior surfaces of your
oven, steering clear of the heating
elements, lamps ,fans, motor shafts,
or anything else that the paste can
get stuck inside of and be hard to get
out. The baking soda will turn a
brownish color as you rub it in; it also
might be chunkier in some places
than others.
●Let it sit for six hours: Allow the
baking soda mixture to rest for at
least 6 hours, or overnight.
●Spray vinegar: Put a small portion of
vinegar in a spray bottle and spritz
wherever the baking soda residue in
your oven was applied. The vinegar
will react with the baking soda and
gently foam.
●Clean out the oven & clean the
accessories: After 12 hours or
overnight, take a damp dish cloth and
wipe out as much of the dried baking
soda paste as you can. Use a plastic
or silicone spatula to help scrape off
the paste as needed.
●Repeat the wiping cycle: Take your
damp cloth and wipe out the
remaining foamy vinegar-baking-soda
mixture. Repeat until all the baking
soda residue is gone. Add more water
or vinegar to your cloth as needed
while wiping to really get the oven
clean and shiny.Do not over-wet to
avoid damaging components.
●Clean all stainless steel & chrome
surfaces & accessories: with a
stainless steel cleaner.
●Begin the self-clean cycle. Please
read the instructions under the knob
conf iguration section of this manual,
prior to operating the self – clean
cycle.

9
HTDF366 – Affluent Series Range Installation
www.hypotheory.com
The handle bar is already assembled
to the range, the instructions below
only apply to replacing the handle
bar.
Handle Bar Installation:
1.Insert the washer between the
handle and the handle latch, turn bar
by hand to tighten in place.
2.Screw in the latch screws behind
the range door wall.
Burner Assembly: The gas burner accessories are disassembled in the box.
The above diagram explains the right way- with a chec mar , and the wrong
way with an “X” mar to install the parts. The best way to measure the burners
cups (ex.labeled F), is to align them next to each burner, the proper cup size
that fits will drop into the burner with ease by hand. Ensure all of the burners
lids (ex. Labeled C,A or B) are in their correct position. The cup nor the lid
should be removed or installed while the oven is on or in operation! Regularly
chec the ignition pin labeled S, and do not trigger the ignition to light until the
burner lids and cups are correctly assembled to avoid damaging the unit.

10
●Gas Line Assembly: All gas
installation must be done by a
licensed plumber. The gas line is
located in the rear of the oven and
does not protrude out to allow the
oven to rest flush against the wall.
The gas line is a ½ inch threaded gas
pipe, there is a sample quic inlet
fitting that must be unscrewed &
replaced with a ½ inch female flare
fitting. Then a gas hose or a gas pipe
must be connected to the female
flare. (Accessories not included, can
be purchased in a home improvement
store/plumbing supply store)
HTDF366 – Affluent Series Range Installation
www.hypotheory.com
●Converting to Natural Gas or
Liquid Propane.
1. Turn the nob to the maximum
position, and ensure the burner flame
is on.
2. Ta e off the nob by pulling
forward carefully, do not lose parts,
and use a screw driver to rotate the
screw in each gas valve.
3. Adjust the screw until the flame is
at the preferred height.
4. Please follow the instructions on
the next page to change the nozzles.
The nozzles must be changed first.

11
HTDF366 – Affluent Series Range Installation
www.hypotheory.com
Propane LP Chart
Code Specification Related Burner
HT.02.07.00013 Ø0.91 #1 Triple Ring Burner 1
HT.02.07.00014 Ø0.75 #2 Rapid Burner 1
HT.02.07.00015 Ø0.6 #3 Semi-rapid Burner 3
HT.02.07.00016 Ø0.48 #4 Auxiliary/Simmer Burner 1
HT.03.13.00009 Ø0.8 Burner inside the Oven 1
Natural Gas NG Chart
Code Specification Related Burner
HT.02.07.00018 Ø1.35 #1 Triple Ring Burner 1
HT.02.07.00019 Ø1.2 #2 Rapid Burner 1
HT.02.07.00020 Ø0.97 #3 Semi-rapid Burner 3
HT.02.07.00021 Ø0.8 #4 Auxiliary 1
HT.03.13.00008 Ø1.32 Burner inside the Oven 1
Total QTY for
Each Oven
Total QTY for
Each Oven
Do not over tighten , just tighten by hand then use a soc et wrench for one half turn
cloc wise. Each nozzle is labeled with the specification number noted below to help
identify them. Li e in the sample photo below. Reference below photo for nozzle position,
each burner type is numbered on the chart and in the diagram. Example- burner labeled 1
is also labeled #1 Triple Ring Burner in the nozzle reference sheet.

12
HTDF366 – Affluent Series Range Installation
www.hypotheory.com
Electrical Oven Installation/Electrical Power Supply Connection: The installation,
debugging, connection & power supply on all HypoTheory 220 volt based electrical
appliances/ or appliances that require wiring configuration must be installed by a licensed
electrician. Each oven supplies a terminal that is compatible to connect to a standard 4 or
3 prong 220/240 volt range cord(sold separately). The rated power of the power supply
should be compatible with a standard 220v/60hz or 220 v/50hz system. The minimum
amp required is 35 amp per brea er (per hot wire)- that is 70 amp total. There are two
wiring configuration options shown below to power the range.
3 Wire Configuration (shown above):
The electrician can install wiring around the
screws or use a standard 3 prong range
cord connection. Please ensure the
terminal washers are resting on top of each
wire in order to conduct electricity to the
range. The two hot wires should individually
connect to the cord/wiring hot wires, the
one neutral wire should connect to the
cord/wiring neutral wire, the ground wire
should connect to the cord/wiring ground
wire. Please ensure all connections are
tight, and ensure the proper screw driver is
used, do not over tighten The
neutral/ground wire must be connected to
the service panel. If there is no ground the
strap will act as a ground shown above.
4 Wire Configuration (shown above):
The electrician can install wiring around the
screws or use a standard 4 prong range
cord connection. Please ensure the
terminal washers are resting on top of each
wire in order to conduct electricity to the
range. The two hot wires should individually
connect to the cord/wiring hot wires, the
one neutral wire should connect to the
cord/wiring neutral wire, the ground wire
should connect to the cord/wiring ground
wire. Please ensure all connections are
tight, and ensure the proper screw driver is
used, do not over tighten The
neutral/ground wire must be connected to
the service panel.

13
HTDF366 – Affluent Series Range Installation
www.hypotheory.com
Installation of the Anti Tip Device: This device will protect the range
from tipping forward, the anti-tip brac et must be installed. To ensure
the anti-tip bolt engages the brac et, refer to the illustration below to
determine proper placement. The size of the drill bit used is entirely
based on the application the device is being installed on
(Drywall,concrete,wood), you must consult with your range installer to
determine the proper drill bit sizes needed to drill holes with.
Step 2: Drill two 10 mm holes in the
wall, the two holes must be 60 mm
apart.
Step 3: Insert anchors into the holes, and
screw the anti-tip device in with M4x500
mm screws.(accessories included)
Step 1: The anti-tip device is
55 mm plus the height of
the bottom side of the oven
top with leg adjustments.
Step 4: Slide the range onto the anti-tip
device carefully: with assistance.

14
HTDF366 – Affluent Series Range Installation
www.hypotheory.com
Installation of the stainless steel board enclosing the
decorating/storage/warming drawer compartment: This device will
beautify the range. It emphasizes the professional-style attribute the
range offers. The compartment can be used for storage of coo ing
ware, or used as a warming drawer for already coo ed foods. The
warming drawer feature can ONLY be used while the gas oven ba ing
feature is in use ONLY, the active gas oven will warm this region.
Please ensure the compartment is empty before the cleaning cycle is
initiated.
Step 2: Ensure all latches are connected
and the stainless steel board is balanced.
Step 1: Rest
the decorating
board into the
pre-installed
oven latches.
FYI: This is not the actual
image of the range displayed.
Some models may have hinges
some may have latches.

15
HTDF366 – Affluent Series Range Installation
www.hypotheory.com
Installation of the Backsplash/Console/Back guard: This device
will protect the range from spills. It also offers an aesthetic value to the
range. It is an optional accessory. The size of the drill bit used is
entirely based on the application the device is being installed on
(Drywall,concrete,wood), you must consult with your range installer to
determine the proper drill bit sizes needed to drill holes with.
FYI: This is not the actual
image of the range,
The range does not have a
handle above the nobs,
only five burners nor a nob
configuration displayed,etc.
Step 1: Align screws into the bac splash &
screw holes, then tighten.(accessories
included)
FYI: The
screw holes
are located
on the rear
corner of
each side of
the range.
Step 2: Align screws under the bac splash
& screw holes, then tighten.(accessories
included)

16
HTDF366 – Affluent Series Range Installation
www.hypotheory.com
Installation of the Range Legs & Optional Leg Shield: The four
legs must be installed to the range.The legs themselves will give the
range an estimated height of 880mm, they are adjustable and can
alter the range height approximately an inch lower or higher than
measurement indicated. The leg shield is an optional accessory and
can be used to hide the legs, if the owner did not wish to expose the
oven legs. The leg shield covers the front, left & right side of the oven.
(All accessories included).
FYI: This is how the oven will loo if the
above mentioned accessories are installed.
This is not the actual image of the range.The
oven legs must be installed, however the leg
shield is optional.
Step 1: Tilt the oven- with the
help of at least two adults total,
try to lay the oven on it's side with
a thic blan et, do not set oven
on its bac nor front.
Step 2: Insert the threaded
leg bolt welded to
each oven leg inside
the leg hole slots,
screw in the washer
via the inner slot by hand.
Step 3: Tilt the oven
upright - ensure the
oven is level. Rotate
the legs to adjust height.
Step 4: Insert the front of the leg shield. Step 5: Overlap the front leg shield with the
side leg shields & screw in.

17
Knob Control Commands Part 1 of 2: for the HTDF366NG/HTDF366LP Models
●The nob labeled 1 is for the optional/alternate bottom gas oven burner- the bottom
oven burner can be used for ba ing foods inside the oven, but can not be used at
the same time as the electrical oven. The gas oven ba ing temperatures range from
slightly under 300 Fahrenheit to slightly over 500 Fahrenheit.
●The nob labeled 2 is an indicator light that turns on when the oven is in use.
●The nob labeled 3 is the oven electrical oven ba ing element nob, you are able to
select between two ba ing cycles: normal or rapid heat technology
Rapid Heat Technology Icon: A unique feature offered by the electrical
oven, allows the user to rapidly ba e, broil, pre-heat or self-clean the oven. The icon
is very similar to the normal ba e icon in appearance, the only difference is the extra
horizontal line above the flame symbol, indicating two solid heating elements are on
at their maximum setting simultaneously.
Normal Ba ing Icon: Is a great feature for the everyday coo that simply needs to
use their oven for normal ba ing functionality.
●The nob labeled 4 is the electrical oven temperature control nob, and it must be
turned on with the timer & the electrical oven ba ing element nob simultaneously,
in order for the electrical oven to wor . The electrical ovens internal thermometer
sensor will automatically turn off the oven once it reaches the correct temperature
control dictated by the nob and turn bac on when heat must be applied to
maintain the designated temperature, the nob ranges from 200 to 500 degrees
fahrenheit, and can attain much hotter fahrenheit settings if it is set for broil and
clean.
HTDF366 – Affluent Series Range Specifications
www.hypotheory.com

18
Broil:The nob labeled 4 can be set to broil, however in order to adequately broil
food, the user must set the ba ing element to the rapid heat technology icon. The
coo must ensure the pre-broiled food are inserted in the absolute top shelve rac .
Please wait till the temperature pro-style gauge has reached the broil mar before
inserting food in the oven cavity. Please disregard the pro-style gauge if it appears
to increase or decrease slightly in temperature readings, this is normal and is due to
the convection fan temporarily blowing in the cavity.
Clean: Please ensure there are no accessories in/on the range during the cleaning
cycle. Please ensure you do not touch the oven while it is in use at all times unless it
is to turn the oven off. The nob labeled 4 can be set to clean, however in order to
properly clean, the user must set the ba ing element to the rapid heat technology
icon. The user must remove all pots, pans, oven accessories, etc- from the inside of
the oven. The user must wait approximately 40 minutes or until the pro-style gauge
is on or about- in-between the broil and clean mar - before declaring the start of the
cleaning cycle. The self cleaning cycle should last no less than 3 hours and no more
than 4 hours. Please disregard the pro-style temperature gauge if it appears to
increase or decrease slightly in temperature readings, this is normal and is due to
the convection fan temporarily blowing in the cavity.
●The nob labeled 5 is the professional-style temperature gauge/thermometer. It will
accurately display the heat settings in the oven. It is perfectly normal for the gauge
to slightly decrease or increase (5% differentiation) in temperature readings during
the coo ing or cleaning cycle due to the convection fan, cooling fan & oven safety
features.
●The nob labeled 6 is the nob for the front-left burner
●The nob labeled 7 is the nob for the bac -left burner
●The nob labeled 8 is the nob for the bac -middle burner
HTDF366 – Affluent Series Range Specifications
www.hypotheory.com

19
●The nob labeled 9 is the nob for the front-middle burner
●The nob labeled 10 is the nob for the bac -right burner
●The nob labeled 11 is the nob for the front-right burner
●The nob labeled 12 is the turn-spit/rotisserie switch. Please read the How-To
Operate The Turn Spit/Rotisserie Kit section of this manual before using this
feature.
●The nob labeled 13 is the timer control. When the timer is used during the
operation of the electrical oven it will instantly turn the electrical oven off. The timer
will also ma e a noise to indicate it has expired. The timer can be used as an on
switch without any timer settings by rotating the timer in the opposing direction.
Timer options normally range from 0 to 60 minutes.
HTDF366 – Affluent Series Range Specifications
www.hypotheory.com

20
HTDF366 – Affluent Series Range Specifications
www.hypotheory.com
●The burner labeled 3 is the semi
rapid burner. It is recommended that
you use coo ing ware with a diameter
of no less than 16 cm and no more
than 24 cm with these 3 identical
burners. They offer a standard output
that can be compared to a
conventional ovens burner, all-
purpose burners are great for the
every day coo , they can be used for
practically any application that does
not require maximum heat nor a low
heat setting.
●The burner labeled 4 is the simmer
burner. It is recommended that you
use coo ing ware with a diameter of
no less than 12 cm and no more than
24 cm. The burner offers a chef's
dream low output, great for allowing
a variety of coo ing options. Simmer
burners are great for eeping your
food warm or maintaining a steady
low heat.
●Each burner comes with an automatic
electronic igniter to light the burner's
flame, each burner has a controlling
nob to open or close the gas valve
as a safety precaution.
●If your flame were ever to unli ely go
out; while on; the range has an
advanced flame retardant technology
that automatically turns off the nob.
●HypoTheory does not guarantee
burner performance expectations.
Six Burner Cooking Functionality
●The burner labeled 1 is the triple
ring burner. It is recommended that
you use coo ing ware with a diameter
of no less than 26 cm and no more
than 30 cm with this burner. It is a
very high output & powerful burner,
and will quic ly heat & boil.
●The burner labeled 2 is the rapid
burner. It is recommended that you
use coo ing ware with a diameter of
no less than 24 cm and no more than
28 cm with this burner. It is a very
high output all-purpose burner, that
can be used for applications that do
not require maximum heat but still
require an abundant amount.