HySecurity MX3114 User manual

Installation Instructions
MX3114
StrongArmPark DC Articulating Arm
Review the illustrations for the steps involved in assembling the
articulating arm and attaching it to the StrongArmPark DC chassis.
Tools required
• Box end wrenches: 7/16 and 9/16 inch • Drill
• Socket head wrenches: 7/16 and 9/16 inch • Drill bit 9/32 inch
• 1/4 - inch Hex key
For detailed views of the assembly, see page 2.
Breakaway bracket and
Mounng bracket assembly
described in StrongArmPark DC
Quick Start Steps, MX3651-01.
If the p of the arm droops or angles up too much, level
the arm by ghtening or loosen the linkage fasteners
that secure the rod ends.
Rod end
Rod end
Arm cap
Tip of the arm
1/4 inch
fasteners
Drill 9/32 inch
mounng holes
Connect arm
light cables.
Tuck wiring
inside arm.
Arm light cables inside arm’s
arculang bracket
www.SecureOpeners.com | [phone] | [email protected]

StrongArmPark DC:
Articulating Arm Assembly
Follow the steps and secure the fasteners as shown.
Technical Support
For technical support, call your installer or authorized HySecurity
distributor. Obtain the serial number of your operator before calling.
For the name of a distributor near you, call HySecurity at 800-321-9947.
12
1
12
2
12
3
Drill 9/32 inch
mounng holes
1/4 inch
fasteners
provided
Arm lights
connecon
Arm lights
connecon
www.SecureOpeners.com | [phone] | [email protected]

StrongArmPark DC: Lighting Connection for Articulated Arm
1. Make sure both AC and DC power switches are turned OFF.
2. Insert leads of wire harness through the hole in chassis between the two bracket mounts. Feed the
cable through the interior of the chassis. Pull enough cable to reach the Smart DC Controller terminals.
NOTE: Connect wire lead to 24VDC. Lights are dim when connected to 12VDC.
3. Attach the end of the wire harness (on the outside of the chassis) to the LED light connector on the
arm. The wire harness connector is keyed. Be sure to seat the connectors before threading close.
CAUTION
To allow full arm travel, the cable loop on the outside of the chassis must be a minimum 8-inches (20 cm) in length.
4. Secure the harness to the chassis with the strain relief bushing.
DC Power
Switch
AC Power
Switch
Remove center plug
to feed wire harness
cable through
chassis.
Remove smaller
plugs to mount
articulating arm
strut.
LED Arm Light
connector
Wire harness
connector
Connect Articulating Arm Cable
Secure cable
with strain relief
bushing.
Cable loop length:
8-inches (20 cm)
Feed Cable through Chassis
Remove Plugs in Chassis
www.SecureOpeners.com | [phone] | [email protected]

5. Connect the one wire lead to the 24VDC power supply terminal.
See wiring illustrations on page 2.
6. Connect the other wire lead to the NO terminal on User Relay 2.
7. Turn on both AC and DC power switches. Arm will cycle to search
for the target home position.
8. When the arm has stopped moving, access the Installer Menu.
9. Set the User Relay 2 logic function to one of the following:
• R2 “27”: LED lights remain on throughout arm travel and turn off when
open limit is reached.
•R2 “28”: LED lights ash throughout arm travel and turn off when open limit
is reached.
NOTE: In the event of AC power loss, either selection (27 or 28) turns off the
lights which preserves battery life.
COM
COM
COM
COM
COM
COM
COM
COM
STOP
OPEN
RADIO
CLOSE
OPEN
OPEN
PARTIAL
EYE
OPEN
EYE
CLOSE
EXIT
LOOP
BLOCK
EXIT
IN OBS
LOOP
OUTOBS
LOOP
CENTER
LOOP
EDGE
EYE
COM
+ 24 V
EMERG
OPEN
SHOW
LEDs
U
S
ER2
C
O
M
N
O
D
C
USER RELAY 1
Electro-mechanical
USER RELAY 2
Solid state
24VDC
24VDC
12VDC
12VDC
See CAUTION
E
D
G
E
+
24V
OP
EN
C
OM
D
U
AL
G
A
T
E
C
OM
B
A
R2 28 FLASH AC
RELAY 2 LOGIC
OPEN CLOSE STOP MENU RESET
PREV NEXT SELECT
Status Display
GATE CLOSED
Installer Menu
R2 0 DISABLED
User Menu
CT 0 (OFF)
Installer Menu
R2 28 FLASH AC
Press MENU twice
at a Run Mode static
display.
To access the Installer Menu,
press and hold RESET & OPEN,
and then release them.
Press Next, until “R2 0 DISABLED” appears.
Press SELECT. The “R2”
characters blink.
Press Next until ““R2 28 FLASH AC” appears (Or
choose R2 “27” if you don’t want the lights to ash.)
Press SELECT again to set the User Relay 2 function.
RELAY 2: INSTALLER MENU FLOW DIAGRAM
www.SecureOpeners.com | [phone] | [email protected]