Hytera HR65X User manual

HR65X Digital Repeater
User Manual
Hytera Communications Corporation Limited

Preface
Welcome to the world of Hytera and thank you for purchasing this product. This manual includes a description of the
functions and step-by-step procedures for use.
To avoid bodily injury or property loss caused by incorrect operation, please carefully read the Safety Information
Booklet before use.
This manual is applicable to the following product:
HR65X Digital Repeater (X may represent 2, 5, 6, 8, or 9)

Copyright Information
Hytera is the trademark or registered trademark of Hytera Communications Corporation Limited (the Company) in the
People's Republic of China (PRC) and/or other countries or areas. The Company retains the ownership of its
trademarks and product names. All other trademarks and/or product names that may be used in this manual are
properties of their respective owners.
The product described in this manual mayinclude the Company's computer programs stored in memory or other media.
Laws in PRC and/or other countries or areas protect the exclusive rights of the Company with respect to its computer
programs. The purchase of this product shall not be deemed to grant, either directly or by implication, any rights to
the purchaser regarding the Company's computer programs. The Company's computer programs may not be copied,
modified, distributed, decompiled, or reverse-engineered in any manner without the prior written consent of the
Company.
Disclaimer
The Company endeavors to achieve the accuracy and completeness of this manual, but no warranty of accuracy or
reliability is given. All the specifications and designs are subject to change without notice due to continuous
technological development. No part of this manual may be copied, modified, translated, or distributed in any manner
without the prior written consent of the Company.
We do not guarantee, for any particular purpose, the accuracy, validity, timeliness, legitimacy or completeness of the
third-party products and contents involved in this manual.
If you have any suggestions or would like to receive more information, please visit our website at:
https://www.hytera.com.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates and can radiate radio frequency energy. If not installed and used in accordance
with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. Verification of harmful interference by this equipment to radio
or television reception can be determined by turning it off and then on. The user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a different circuit to that of the receiver's outlet.
Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:

This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.
Note: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
Operational Instructions and Training Guidelines
To ensure optimal performance and compliance with the occupational/controlled environment RF energy exposure
limits in the above standards and guidelines, users should transmit not more than 50% of the time and always adhere
to the following procedures:
Antenna gain must not exceed 10 dBi.
The antenna must be installed complying with the requirements of manufacturer or supplier, and it must be at
least 86 cm away from human body.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an occupational/controlled environment.
This transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter. This
equipment should be installed and operated with a minimum distance of 86 cm between the radiator and your body.
ISEDC Radiation Exposure Statement
This equipment complies with ISEDC RF radiation exposure limits set forth for an occupational/controlled
environment. This transmitter must not be co-located or operating in conjunction with anyother antenna or transmitter.
This equipment should be installed and operated with a minimum distance of 86 cm between the radiator and your
body.
IC Exposition Aux Radiations
Cet équipement est conforme avec ISEDC les limites d'exposition aux rayonnements définies pour un environnement
professionnel/contrôlé. Cet émetteur ne doit pas être co-localisés ou fonctionner en conjonction avec une autre antenne
ou émetteur. Cet équipement doit être installéet utiliséavec une distance minimale de 86 cm entre leradiateur & votre
corps.
EU Regulatory Conformance
As certified bythe qualified laboratory, the product is in compliance with the essential requirements and other relevant
provisions of 2014/53/EU.
The maximum antenna gain is 10 dBi. The minimum safety distance is 103 cm.
Please note that the above information is applicable to EU countries only.

Specifications
Parameter
Description
Frequency
Digital Repeater: 400–470 MHz
GPS L1 C/A, BDS B1I: 1559–1610 MHz
Output Power
High: 44 dBm
Middle: 40 dBm
Low: 30 dBm

User Guide
Contents
i
Contents
1. Packing List..............................................................................................................................................3
2. Product Layout......................................................................................................................................... 4
3. Precaution.................................................................................................................................................6
4. Installation ................................................................................................................................................7
4.1 Tools..................................................................................................................................................... 7
4.2 Procedure.............................................................................................................................................7
5. Basic Operation........................................................................................................................................ 9
5.1 Turning On or Off the Repeater ...........................................................................................................9
5.2 Switching the Channel.......................................................................................................................... 9
5.3 Adjusting the Volume ...........................................................................................................................9
5.4 (Optional) Transmitting.........................................................................................................................9
6. Status Indication .................................................................................................................................... 10
6.1 LED Indicator......................................................................................................................................10
6.2 Seven-Segment LED..........................................................................................................................10
7. Alarm Information.................................................................................................................................. 12
7.1 External Power Under-voltage or Over-voltage Alarm.......................................................................13
7.1.1 Description ...............................................................................................................................13
7.1.2 Solution ....................................................................................................................................13
7.2 TX/RX Unlocked Alarm ......................................................................................................................13
7.2.1 Description ...............................................................................................................................13
7.2.2 Solution ....................................................................................................................................13
7.3 PA Over-temperature Alarm...............................................................................................................13
7.3.1 Description ...............................................................................................................................13
7.3.2 Solution ....................................................................................................................................14
7.4 VSWR Alarm ......................................................................................................................................14
7.4.1 Description ...............................................................................................................................14
7.4.2 Solution ....................................................................................................................................15
7.5 Off-lease Alarm...................................................................................................................................15
7.5.1 Description ...............................................................................................................................15
7.5.2 Solution ....................................................................................................................................15
7.6 Slave Unregistered Alarm ..................................................................................................................15
7.6.1 Description ...............................................................................................................................15
7.6.2 Solution ....................................................................................................................................15
7.7 Repeater Disabled Alarm...................................................................................................................15
7.7.1 Description ...............................................................................................................................15
7.7.2 Solution ....................................................................................................................................16

Contents
User Guide
ii
7.8 Low Forward Power Alarm.................................................................................................................16
7.8.1 Description ...............................................................................................................................16
7.8.2 Solution ....................................................................................................................................16
7.9 Network IP Conflict Alarm ..................................................................................................................16
7.9.1 Description ...............................................................................................................................16
7.9.2 Solution ....................................................................................................................................16
7.10 Invalid Network IP Alarm..................................................................................................................17
7.10.1 Description .............................................................................................................................17
7.10.2 Solution ..................................................................................................................................17
8. Troubleshooting..................................................................................................................................... 18
9. Care and Cleaning.................................................................................................................................. 19
9.1 Product Care ......................................................................................................................................19
9.2 Product Cleaning................................................................................................................................ 19
10. Optional Accessories .......................................................................................................................... 20
11. Abbreviations .......................................................................................................................................21

User Guide
Documentation Information
1
Documentation Information
Documentation Conventions
Instruction Conventions
Icon
Description
Indicates information that can help you make better use of your product.
Indicates references that can further describe the related topics.
Indicates situations that could cause data loss or equipment damage.
Indicates situations that could cause minor personal injury.
Indicates situations that could cause major personal injury or even death.
Notation Conventions
Item
Description
Example
Boldface
Denotes menus, tabs, parameter names,
window names, dialogue names, and
hardware buttons.
To save the configuration, click Apply.
The Log Level Settings dialogue box appears.
Press the PTT key.
" "
Denotes messages, directories, file names,
folder names, and parameter values.
The screen displays "Invalid Battery!".
Open "PSS.exe".
Go to "D:/opt/local".
In the Port text box, enter "22".
>
Directs you to access a multi-level menu.
Go to File > New.
Italic
Denotes document titles.
For details about using the DWS, refer to
Dispatch Workstation User Guide.
Courier New
Denotes commands and their execution
results.
To set the IP address, run the following
command:
vos-cmd - m name IP

Documentation Information
User Guide
2
Revision History
Document
Version
Product
Version
Release Date
Description
00
V00
July 2022
Initial release.

User Guide
Packing List
3
1. Packing List
Unpack carefully and check that you have received the following items. If any item is missing or damaged, contact
your dealer.
Item
Quantity (PCS)
Item
Quantity (PCS)
Repeater
1
Documentation Kit
1
Power Cord
1
/
/
Figures in this document are for reference only.

Product Layout
User Guide
4
2. Product Layout
No.
Part Name
No.
Part Name
1
Bottom cover
12
Analog mode indicator
2
USB port
13
Timeslot A TX indicator
3
TX/Duplexer antenna connector (UHF female)
14
Timeslot A RX indicator
4
Accessory connector
15
Timeslot B TX indicator
5
Ethernet port
16
Timeslot B RX indicator
6
Power inlet
17
Alarm indicator
7
RX antenna connector (SMA female)
18
Fan
8
GNSS antenna connector (SMA female)
19
Volume/Channel up key
9
Aviation port
20
Seven-segment LED
10
On-Off key
21
Volume/Channel down key
11
Digital mode indicator
22
Battery latch

User Guide
Product Layout
5
Except that the low-power HR65X features no fan but the high-power HR65X features one, the other hardware
of the two types is the same.

Precaution
User Guide
6
3. Precaution
Before installation and use, read the following instructions carefully.
Install the repeater in a dry and well-ventilated place.
Use the repeater in an environment where the temperature is between –30°C and +60°C and the relative humidity
is equal to or lower than 95%.
Ensure that the operating voltage is 12–16.8 V DC.
For more information, refer to the Safety Information Booklet.

User Guide
Installation
7
4. Installation
You can place the repeater on the desk, or install the repeater on the wall.
4.1 Tools
Electric drill
Screwdriver
Wrench
Anti-static gloves
4.2 Procedure
Install the three pegs onto the fixing plate with three M3 screws at holes marked with "B".
Fix the fixing plate to the back of the repeater with four M4 screws.
Install the repeater on the wall.
Before installation, make sure the weight of the repeater is within the load bearing capacity of the wall.
a. Hold the bracket horizontally to a proper position on the wall, and then mark the locations of the three holes
(Φ = 8 mm, h = 60 mm) as anchor points.

Installation
User Guide
8
b. Drill three holes at the anchor points with an electric drill.
c. Fix the bracket onto the wall with three M6 expansion bolts.
d. Dock the three holes on the bracket with the three pegs on the back of the repeater.

User Guide
Basic Operation
9
5. Basic Operation
5.1 Turning On or Off the Repeater
Automatically Turn On
When connected to external power supply, the repeater automatically turns on.
Manually Turn On or Off
When connected to external power supply, long press the On-Off key to turn on or off the repeater.
5.2 Switching the Channel
In the standby mode, press the Volume/Channel Up key or the Volume/Channel Down key.
The seven-segment LED displays the current channel number.
5.3 Adjusting the Volume
To switch the Volume/Channel Up key to the volume mode, press the key for five seconds.
If you do not have any operation or you long press the Volume/Channel Up key within five seconds, the key
will switch to the channel mode.
Press the Volume/Channel Up key to increase or the Volume/Channel Down key to decrease the volume.
5.4 (Optional) Transmitting
Connect the remote speaker microphone (RSM) to the repeater.
Press the push-to-talk (PTT) key on the RSM.
You can learn about the repeater status from LED indicators. For details, see 5 错误!书签自引用无效。.
The RSM is optional.
Use the RSM specified by Hytera.
PTT TX Channel Type and TX Contact Name are configured by the dealer.
The repeater gives no indication or response if it detects no TX contact name on the current channel (digital
or hybrid) after PTT is pressed.

Status Indication
User Guide
10
6. Status Indication
6.1 LED Indicator
Indicator
Status
Description
Digital mode indicator
Glows blue
The repeater is in the digital mode.
Analog mode indicator
Glows orange
The repeater is in the analog mode.
Alarm indicator
Glows red
An exception occurs (The seven-segment LED
displays the corresponding alarm code).
Timeslot A TX indicator
Glows red
Analog mode: transmitting
Digital mode: Timeslot A is transmitting.
Timeslot A RX indicator
Glows green
Analog mode: receiving
Digital mode: Timeslot A is receiving.
Timeslot B TX indicator
Glows red
Timeslot B is transmitting in the digital mode.
Timeslot B RX indicator
Glows green
Timeslot B is receiving in the digital mode.
6.2 Seven-Segment LED
Alarm Code
Alarm
Code
Description
Alarm
Code
Description
E3
External power under-voltage
alarm
EE
Repeater disabled alarm
E4
TX unlocked alarm
Eb
Low forward power alarm
E5
RX unlocked alarm
EH
External power over-voltage alarm
E6
Over-temperature alarm
H3
Network IP conflict alarm
E7
Voltage standing wave ratio
(VSWR) alarm
H5
Invalid network IP alarm
E8
Off-lease alarm
bP
Backup alarm
E9
Slave unregistered alarm
/
/

User Guide
Status Indication
11
Channel Code
Channel Code
Description
N
Indicates the current channel number, for example, 1, 2, 3, or more.

Alarm Information
User Guide
12
7. Alarm Information
With the Alarm feature enabled by your dealer, the repeater automatically triggers an alarm if any exception occurs.
When the alarm is active, the LED displays the corresponding alarm code and the alarm indicator glows red.
The following table describes alarms in detail.
Alarm
Code
Alarm Name
Description
E3
External power
under-voltage alarm
The repeater fails to work. In this case, if the Repeater Backup feature is
enabled on the CPS, the repeater starts a backup.
E4
TX unlocked alarm
The repeater fails to work. In this case, if the Repeater Backup feature is
enabled on the CPS, the repeater starts a backup.
E5
RX unlocked alarm
The repeater fails to work. In this case, if the Repeater Backup feature is
enabled on the CPS, the repeater starts a backup.
E6
PA over-
temperature alarm
The repeater fails to work. In this case, if the Repeater Backup feature is
enabled on the CPS, the repeater starts a backup.
E7
Voltage standing
wave ratio (VSWR)
alarm
The repeater automatically works at lower TX power.
E8
Off-lease alarm
The repeater fails to work.
E9
Slave unregistered
alarm
The repeater cannot repeat the signal or data in the IP multisite connect
network.
EE
Repeater disabled
alarm
The repeater fails to work.
Eb
Low forward power
alarm
The repeater stops transmission when the TX power is 0 W.
EH
External power
over-voltage alarm
The repeater fails to work. In this case, if the Repeater Backup feature is
enabled on the CPS, the repeater starts a backup.
H3
Network IP conflict
alarm
Network services of the repeater are unavailable.
H5
Invalid network IP
alarm
Network services of the repeater are unavailable.

User Guide
Alarm Information
13
Alarm
Code
Alarm Name
Description
bP
Backup alarm
The repeater works as a standby repeater.
7.1 External Power Under-voltage or Over-voltage Alarm
7.1.1 Description
When the repeater detects that the voltage of the external power supply is out of range, the alarm indicator glows red
and the LED displays "E3" for under-voltage alarm or "EH" for over-voltage alarm.
In this case, the repeater fails to work.
7.1.2 Solution
Check whether the power adapter is damaged.
If yes, replace the power adapter.
If no, go to step 2.
Check whether the input voltage of external power supply is beyond the repeater's operating voltage range with a
voltmeter.
If yes, replace the power adapter.
If no, contact your dealer for technical support.
7.2 TX/RX Unlocked Alarm
7.2.1 Description
When the TX/RX phase-locked loop unlocks, the alarm indicator glows red and the LED displays "E4" for TX unlock
or "E5" for RX unlock.
In this case, the repeater automatically fails to provide certain features.
7.2.2 Solution
Contact your dealer for technical support.
7.3 PA Over-temperature Alarm
7.3.1 Description
When the repeater detects that the internal temperature of the PA module exceeds the upper threshold, the alarm