Hyundai power products HDCBE1400 User manual

1
ELECTRIC BRUSHCUTTER & GRASSTRIMMER
HDCBE1400
WARNING: Read thoroughly the instruction manual before use

2
1.SAFETY WARNINGS
Safe operating practices
Training
a)Read the instructions carefully. Be familiar with the
controls and the correct use of the machine.
b) Never allow children or people unfamiliar with these
instructions to use the machine. Local regulations can
restrict the age of the operator.
c)Keep in mind that the operator or user is responsible
for accidents or hazards occurring to other people or
their property.
Preparation
a)Before use check the supply and extension cord for
signs of damage or aging. If the cord becomes
damaged during use, disconnect the cord from the
supply immediately. DO NOT TOUCH THE CORD
BEFORE DISCONNECTING THE SUPPLY. Do not
use the machine if the cord is damaged or worn.
b)Before use, always visually inspect the machine for
damaged, missing or misplaced guards or shields.
c)Never operate the machine while people, especially
children, or pets are nearby.
Operation
a)Keep supply and extension cords away from cutting
means.
b)Wear eye protection and stout shoes at all times while
operating the machine.
c)Avoid using the machine in bad weather conditions
especially when there is a risk of lightning.
d)Use the machine only in daylight or good artificial light.
e)Never operate the machine with damaged guards or
shields or without guards or shields in place.
f) Switch on the motor only when the hands and feet are
away from the cutting means.

3
g)Always disconnect the machine from the power supply
(remove the plug from the mains):
1.whenever the machine is left unattended;
2.before clearing a blockage;
3.before checking, cleaning or working on the
machine;
4.after striking a foreign object;
5.whenever the machine starts vibrating abnormally.
h)Take care against injury to feet and hands from the
cutting means.
i) Always ensure that the ventilation openings are kept
clear of debris.
Maintenance and storage
a)Disconnect the machine from the power supply (i.e.
remove the plug from the mains, remove the disabling
device or removable battery) before carrying out
maintenance or cleaning work.
b)Use only the manufacturer’s recommended
replacement parts and accessories.
c)Inspect and maintain the machine regularly. Have the
machine repaired only by an authorized repairer.
d)When not in use, store the machine out of the reach of
children.
Recommendation
The machine should be supplied via a residual current
device (RCD) with a tripping current of not more than 30
mA.
Additional instructions
Proper safety precautions must be observed. Like all
power equipment this unit must be handled carefully. DO
NOT EXPOSE YOURSELF OR OTHERS TO DANGER.
Follow these general rules. Do not permit others to use
this machine unless they are thoroughly responsible and
have read, and understand the machine manual and are
trained in its operation.

4
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do
not play with the appliance.
This product must be and operated by experienced
users only. It is important that non experienced users
get a full training before using this tool
If you give this machine to another person, please also
provide it with this instruction manual.
Always wear safety goggles for eye protection. Dress
properly; do not wear loose clothing or jewelry that
could become caught in moving parts of the unit. Safe,
sturdy, nonskid footwear should always be worn. Long
hair should be tied back. It is recommended that legs
and feet be covered to protect from flying debris during
operation.
Inspect the entire machine for loose parts (nuts, bolts,
screws, etc.) and any damage. Repair or replace as
necessary before using the machine. DO NOT USE
any attachment with this power head other than the
ones recommended by our company. Serious injury to
the operator or bystanders could result as well as
damage to the machine.
Always use proper handles and shoulder strap when
cutting.
Never attempt to make engine adjustments while the
unit is running and strapped to the operator. Always
make engine adjustments with the unit resting on a flat,
clear surface.
Do not use the unit if it is damaged or poorly adjusted.
Never remove the machine’s guard. Serious injury to
the operator or bystanders could result as well as
damage to the machine.
Inspect the area to be cut and remove all debris that

5
could become entangled in the nylon cutting head. Also
remove any objects that the unit may throw during
cutting.
Keep children away. Onlookers should be kept at a
safe distance from the work area, at least 15 meters
(50 FEET).
Never leave the machine unattended.
Do not use this unit for any job other than those for
which it is intended as described in this manual.
Do not overreach. Keep proper footing and balance at
all times. Do not run the unit while standing on a ladder
or on any other unstable footing location.
Keep hands and feet clear of the nylon cutting head or
blade while unit is in use.
Do not use this type of machine for sweeping away
debris.
Do not use the unit when you are tired, ill or under the
influence of medication, drugs or alcohol.
Use nylon cutting head which is free of damage. If a
stone or any other obstacle is hit, stop the engine and
check the nylon cutting head. A broken or unbalanced
nylon cutting head must never be used.
Store in a locked, well-ventilated area only.
Ensure safe and proper performance of your product.
These parts are available from your dealer. The use of
any other accessories or attachments may cause a
potential hazard or injury to the user, damage to the
machine and void this warranty.
Clean the machine completely, especially, the fuel tank,
its surroundings, and the air cleaner.
Stay clear of other workers or bystanders by at least 15
meters/50 feet.
Whenever approaching an operator of the machine,
carefully call his attention and confirm that the operator
stop the engine. Be careful not to startle or distract the
operator which can cause an unsafe situation.
Never touch the nylon cutting head or blade whenever
the engine is running. If it is necessary to replace the

6
protector or cutting attachment, be sure to stop the
engine and confirm that the cutting device has stopped
running.
The engine should be turned off when the machine is
moved between work areas
Be careful not to hit the nylon cutting head against
stones, or the ground.
Unreasonable rough operation will shorten the life of
the machine as well as create an unsafe environment
for yourself and those around you.
Pay attention to loosening and overheating of parts. If
there is any abnormality of the machine, stop operation
immediately and check the machine carefully. If
necessary, have the machine serviced by an
authorized dealer. Never continue to operate a
machine which may be malfunctioning.
Pay special attention to operation in the rain or just
after the rain as the ground may be slippery.
If you slip or fall to the ground or into a hole, release the
throttle lever immediately.
Be careful not to drop the machine or hit it against
obstacles.
Before proceeding to adjust or repair the machine, be
sure to stop the engine and detach the spark plug.
Make periodic inspections to assure safe and efficient
operation. For a thorough inspection of your machine,
please contact a dealer.
It is believed that a condition called Raynaud’s
phenomenon, which affects the fingers of certain
individuals, may be brought about by exposure to
vibration and cold. Loss of color and numbness in the
fingers. The following precautions are strongly
recommended because the minimum exposure which
might trigger the ailment is unknown.
Keep your body warm, especially the head, neck, feet,
ankles, hands and wrists.
Maintain good blood circulation by performing vigorous
arm exercises during frequent work breaks and also by

7
not smoking.
Limit the hours of operation. Try to fill each day with
jobs where operating the brush cutter or other
hand-held power equipment is not required.
If you experience discomfort, redness and swelling of
the fingers followed by whitening and loss of feeling,
consult your physician before further exposing yourself
to cold and vibration.
Always wear ear protection, loud noise for long time
can make hearing debase even lost hearing.
Wear a total face and head protection.
Wear no-slip heavy duty work gloves to improve your
grip on the brush cutter handle. Gloves also reduce the
transmission of machine vibration to your hands.
WARNING: The cutter area is still dangerous while
the machine is coasting to a stop.
When transport, this unit must be handled carefully. Do
not expose yourself or others to danger.
Envelop the blade before storage. Keep children away
from it.
Never remove the machine’s guard.
Do not store in a closed area where fuel vapors can
reach an open flame from hot water heaters, furnaces,
etc. Store in a locked, well-ventilated area only.
Never place the machine in any places where there are
flammable materials (dry grass, etc.), combustible
gasses or combustible liquids.
National regulation can restrict the use of the machine.
Never modify a trimmer or cutter in any way.
Improper use of the machine can cause SERIOUS OR
FATAL PERSONAL INJURY.
The extension cable shall not be lighter than the
standardized code H05 RN-F/H05 VV-F. See your
retailer or manufacturer for more advice.
Supply cord must be replaced by manufacturer,
service agent or qualified persons when it is damaged.
Never to replace the non-metallic cutting means with
metallic cutting means.

8
Walk on slopes, never run
WARNING: Never to touch moving hazardous parts
before the machine is disconnected from the mains
and the moving hazardous parts have come to a
complete stop
WARNING: Never to connect a damaged cord to the
supply or touch a damaged cord before it is
disconnected from the supply.
When the power extension cord is damaged or ageing,
should be replaced by manufacturer, service agent or
qualified persons.
If the electrical cable is damaged, please immediately
switch off the power supply.
If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
Kickback and Related Warnings
● Kickback is a sudden reaction to a pinched or snagged
rotating wheel, backing pad, brush or any other accessory.
Pinching or snagging causes rapid stalling of the rotating
accessory which in turn causes the uncontrolled power
tool to be forced in the direction opposite of the
accessory’s rotation at the point of the binding.
● For example, if an abrasive wheel is snagged or pinched
by the workpiece, the edge of the wheel that is entering
into the pinch point can dig into the surface of the material
causing the wheel to climb out or kick out. The wheel may
either jump toward or away from the operator, depending
on direction of the wheel’s movement at the point of
pinching. Abrasive wheels may also break under these
conditions.
● Kickback is the result of power tool misuse and/or
incorrect operating procedures or conditions and can be
avoided by taking proper precautions as given below.

9
a) Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
b) Do not position your body in the area where power
tool will move if kickback occurs. Kickback will propel
the tool in direction opposite to the wheel’s movement at
the point of snagging.
c) Use special care when working corners, sharp
edges etc. Avoid bouncing and snagging the
accessory. Corners, sharp edges or bouncing have a
tendency to snag the rotating accessory and cause loss of
control or kickback.
Residual risks
Even if you use this power tool correctly, there are
always residual risks. The following hazards may arise in
connection with the structure and manufacture of this
power tool:
1. Hearing impairment if no suitable hearing protection is
worn.
2. Cuts if no suitable protective clothing is worn.
3. Health damage resulting from vibration in the hands
and arms if the device is used for a long period of time or
is not handled and maintained properly.
Warning! This machine generates an electromagnetic
field during operation. This field may, in certain
circumstances, affect active or passive medical implants.
To reduce the risk of serious injury or death, persons
with medical implants should consult their physician and
the medical implant manufacturer before using the
machine.
Explanation of symbols
This graphic accompanied by the words WARNING and DANGER
calls attention to an act of a condition which can lead to SERIOUS
INJURY.

10
READ & UNDERSTAND Operator’s Manual and Safety Manual
ALWAYS WEAR EYE PROTECTION, EAR PROTECTION AND
HEAD PROTECTION.
GUARANTEE SOUND POWER LEVEL
Distance between bystanders and the tool must be at least 15m
People must kept away from the work area
Do not expose to rain and humidity
Be careful to the rebound
Caution: If the electrical cable is damaged, please immediately switch off the power
supply.
Wear a Head protection
Do not use metal blades! (Unless otherwise stated in this manual)
KEEP BYSTANDERS AT LEAST 15 M AWAY.
Wear protective gloves and protective shoes

11
Intended use
This machine can be used with the cutting wire as a trimmer for cutting grass and weeds of small
thickness and in small quantity and with the cutting blade as a brush cutter for cutting denser
vegetation. This machine must not be used for cutting or other cutting operations where the cutting
tool must be lifted above the ground. This machine is only authorized for private use. Any other use
or modification of this machine is prohibited and involves high risks.
2. YOUR PRODUCT
a. Description
1. Supply cable
2. Motor
3. Upper tube shaft
4. Harness support
5. Connector
6. Lower tube shaft
7. Carter of protection
8. Wire cutting line
9. Metal cutting blade
10. Angle drive
11. Handlebar support
12. Handle and handle with switch on/off and switch-lock release button
13. Electrical wiring
14. Harness
15. Cutting head

12
b. Technical data
3. ASSEMBLY
Model HDCBE1400
Power 1400 W
Voltage 230V~50Hz
Speed (brushcutter) 8500 /min
Cutting diameter (brushcutter) 255mm
Thickness cutting (brushcutter) 1.4mm
Speed (grass trimmer) 7200 /min
Cutting diameter (grass trimmer) 420mm
Cutting thickness (grass trimmer) Φ1.6mm
Weight) 5.2 kg
Sound pressure level LpA : 75 dB(A) ; K= 3.0dB(A)
Sound power level LwA :75 dB(A) ; K= 3.0dB(A)
Guarantee sound power level LWA =96 dB(A)
Vibrations 4.421 m/s2K= 1.5 m/s2

13
Before working on the device, disconnect it from the power supply.
Use only original parts and be careful when assembling the brushcutter. Risk of injury!
Before working, you must mount the safety guard on the cutting device, and the two tubes.
Assemble the tool as explained below and use the pictures above.
MOUNTING THE TWO TUBES OF THE SHAFT (FIG 2)
1. Push the two parts of the tubular shaft together (hole at the top of the bottom tube); you will hear
a click.
2. Put and tighten the screw cap in the correct direction.
3. Before starting the machine, check that the lower tube is firmly installed and secured. Before
starting the machine, make sure that the rod of the tube is closed and secure and that it is in the
correct position.
Dismantling
to disassemble, proceed in the reverse direction of 8.1, Lift the cover plate, press the locking tab
and remove the lower tube.
MOUNTING THE HANDLEBAR (FIG 3)
1. Loosen the 4 Allen screws (A) on the upper tube and remove the handlebar bracket.
2. Insert the handlebar onto the bracket; tighten it with the bracket and the 4 Allen screws (as
shown).
3. Secure the cable with cable ties (rilsan type)

14
Make sure the wiring is not bent or broken.
MOUNTING THE CARTER OF PROTECTION (FIG 4)
Place the protective cover on the shaft. Screw the Allen screws as shown.
MOUNTING THE METAL CUTTING BLADE (FIG 5)
when working with the metal cutting blade, wear gloves.
1. On the shaft, insert in the following order:
2. Tool drive, metal cutting blade, drive washer, cover bell and the holding nut.
3. Secure the shaft by inserting a metal rod on the side of the drive gear and on the tool drive.
Tighten the retaining nut counterclockwise with the supplied wrench.
Disassembly:
Insert a metal shaft locking pin into the hole on the side of the drive gear and on the tool drive.
Loosen the retaining nut clockwise with the wrench and remove the cover bell, the drive washer
and the metal cutting blade.
MOUNTING THE WIRE CUTTER HEAD (FIG 6)
1. Add the tool drive on the spindle. Add and screw the wire head manually counterclockwise as
shown (block the drive shaft rotation with the inserted rod).
2. Never use the brush head without the plastic housing.
Disassembly:
Manually remove the wire head. Secure the drive shaft with the metal rod inserted in Fig 6.
HARNESS ATTACHMENT
To work with the device, always wear it with the harness. Before removing the harness, always turn
off the appliance. There is a risk of injury.
1. Attach the harness
2. Adjust the length of the shoulder strap with the belt to 10 cm under the hips.
4. OPERATION
OPERATING THE BRUSH MACHINE
Do not use the device without the carter of protection. Before each use, make sure that the
appliance is functional. Make sure the power supply matches the safety label. When working with
the electric brush cutter, always wear protective equipment.
Protect yourself from noise and comply with local regulations. The use of the device may be
prohibited or limited on certain days (Sundays and holidays), at certain times (noon, evening), or in
certain areas (spas, clinics).
SWITCH ON / OFF (FIG 7)
1. Connect the appliance to the power supply.
Be sure to stand upright and hold the device firmly with both hands. Do not place the cutting head
on the floor.
2. To switch on, press the lock with the right thumb (B) and press or release the switch (A). Release
the lock.

15
3. To stop, release the M / A button (A). Switching for continuous operation is not possible. After
turning the unit off, the head continues to run for several seconds. The M / A switch must not be
locked.
When released, the engine must stop. If the switch is damaged, do not continue working with the
machine.
EXTENSION OF THE WIRE IN NYLON
Your device is equipped with a two-wire automatic extension, tap the button of the wire head on the
ground, brush cutter on, the wires will come out automatically. The length of the wires will be
adjusted automatically by the cutting blade on the safety guard.
Caution: Regularly clean the wire knife to ensure proper cutting.
Check regularly that the nylon wire is not damaged and always has the correct length.
If the cutting power is reduced, turn the appliance on and hold it above the grass. Touch the floor
with the head. The wires are automatically extended.
When the end of the wire is less than 2.5 cm:
• Switch off the appliance and disconnect it
• press the coil to lock it and pull the remaining wire strongly
• too short wires do not have enough centrifugal force to lengthen automatically
If you do not see the end of the thread:
• Replace the cutting head (see chapter Maintenance and cleaning).
CUTTING INSTRUCTIONS
• Always wear appropriate harness and protective clothing during use.
• When starting or working, make sure that the cutting head does not touch any stone, gravel, wire
or other foreign matter.
• During use, avoid too much effort on the equipment.
• Avoid contact with fixed objects (rock, wall, fence, batten, etc.). Use the crankcase edge to
maintain the correct distance.
• Do not run over the cable with the machine running. This can cause damage. The cable must
remain on the back of the user.
• Start the unit before approaching the lawn.
• Begin mowing from the electrical connection, do not approach the cutting head of the electric wire
and work away from it.
• Cut the tall grass in several stages from top to bottom.
• Do not cut damp or wet grass.
WORKING WITH THE CUTTING HEAD
• Short or worn wires cut badly. If there is an inefficient cut, check if there is any wire remaining in
the coil. Read the paragraph Wire extension.
• During use, hold the cutting head just above the floor at all times and gently rotate the unit. Cut
gently and keep the machine tilted about 30 ° forward.
WORKING WITH THE METAL BLADE
Make sure the blade is properly mounted. Replace damaged or blunt blades. There is a risk of
injury!
• Blades cut only free surfaces. Inspect the area thoroughly and remove any foreign matter. Avoid

16
impacts with stones, metal or other obstacles. The blades could be damaged and there is a risk of
retro-shock.
• Inspect the damaged blades regularly and replace if necessary.
• Do not use the appliance to cut rejects or thickets.
• During use, hold the head above the floor and rotate the appliance like a regular left and right arc.
• Do not hold the cutting head tilted.
5. MAINTENANCE AND STORAGE
Before working on the appliance, unplug it.
If work is not described in this manual, it must be done by the authorized service. Use original parts
and be careful when installing the cutting blade. There is a risk of injury!
Never use worn or non-original parts. Use only genuine parts. Never use metal wires. Use of
non-original parts may result in adverse health effects and irreparable damage to the unit and
immediately voids the warranty.
MAINTENANCE OF ANGLE RETURN
Before each use, check and add, if necessary, the grease for the angle drive (Fig 8A).
Remove the screw on the side of the return housing. Lubricant Castrol LMX.
See page 9 for the pictures for the maintenance.
REPLACING THE CUTTING HEAD (FIGURE 9)
1. Disconnect the power supply.
2. Turn the appliance upwards to raise the head.
3. The coil housing and the coil are inserted only. To open, remove the cover (A) from the cover (C).
Remove the coil (B).
4. The coil is supported by a spring, on either side of the spring there is a washer (top and bottom).
5. To reload coil D with wire, pull the wires through the eyelets (E) of the housing. Hold the wires in
the eyelets (E) of the reel housing. Push the reel into the housing. Pull the two wires. Check that the
resorts are properly installed. Replace the spool cover.
6. Press and hold the knob (D) and pull the thread sufficiently past the automatic thread cutter.
REPLACING THE BLADE (FIGURE 10)
Check the blade.
1Loosen the fastenings screws (B) and remove the blade (A).
2. Place a new knife and secure it with a screwdriver.
CLEANING
• Clean and maintain the appliance regularly. This will ensure performance and durability.
• After each use, remove the grass and soil from the brush cutter and the safety guard.
• Keep the ventilation slots clean and free of grass.
• Clean the appliance with a soft brush or cloth.
Do not spray water on the appliance or soak it in water. Do not use detergent or solvent. The device
would be irreparably damaged. Chemicals can attack the plastic parts of the device.

17
SERVICE AND SPARE PARTS
Have your appliance checked by qualified personnel using original parts. This will ensure the safety
of the tool. If you require technical advice, repairs or genuine parts, contact the SWAP service
nearest you. For information or places of service, go to: www.swap-europe.com.
When ordering spare parts, please indicate the part number, you can find them at:
www.swap-europe.com.
STORAGE
• Clean your appliance and its accessories after each use. This prevents the formation of clusters.
• Store the device in a dry place away from dust and out of reach of children.
• Do not store the unit in direct sunlight.
• Do not place the appliance in plastic bags as mildew may appear.
• Do not place the unit under a protective cover. Hang it on a wall with the top of the handle. Make
sure the cover does not touch anything. Otherwise, there is the risk of crankcase deformation and
thus a change of the safety characteristics.
6. DISPOSAL
Electrical products should not be discarded with household products. According to the European
Directive 2012/19/EC on waste electrical and electronic equipment and its implementation into
national law, electrical products used must be collected separately and disposed of at collection
points provided for this purpose. Talk with your local authorities or dealer for advice on recycling.

18
7. DECLARATION OF CONFORMITY
GB / DECLARATION OF CONFORMITY
BUILDER SAS
ZI, 32 rue aristide Bergès – 31270 Cugnaux - France
Tel : [phone] Fax : [phone]
declares that the machines:
ELECTRIC BRUSHCUTTER &GRASSTRIMMER
Model: HDCBE1400
And in accordance with the following directives:
Directive Machine 2006/42/EC
Directive EMC 2014/30/EU
Rohs Directive (EU)2015/863 amending 2011/65/EU
Noise Directive 2000/14/EC Annex VI & Directive 2005/88/EC
Measured sound power level LwA : 95 dB (A) K=3 dB (A)
Guaranteed sound power level LwA : 96 dB (A) (According to ISO 2000/14/EC)
Notified body
the people name holding the technical file：Mr.Olivier Patriarca
Serial No.: 20211235760-20211236459
have been designed in compliance with the following standards:
Philippe MARIE / PDG
Cugnaux, 25/09/2021
EN 60335-1:2012+A11:2014+A13:2017+A1:2019+A2:2019; EN 50636-2-91:2014
EN62233:2008 ; EN 55014-1:2017; EN ISO11806-1: 2011
EN 55014-2:2015 ; EN 61000-3-2:2014 ; EN 61000-3-3:2013

WARRANTY
The manufacturer guarantees the product against defects in material and workmanship for a period of 2
years from the date of the original purchase. The warranty only applies if the product is for household use.
The warranty does not cover breakdowns due to normal wear and tear.
The manufacturer agrees to replace parts identied as defective by the designated distributor. The
manufacturer does not accept responsibility for the replacement of the machine, in whole or in part , and/or
ensuing damage.
The warranty does not cover breakdowns due to:
• insu󰀩cient maintenance.
• abnormal assembly, adjustment or operations of the product.
• parts subject to normal wear and tear.
The warranty does not extend to:
• shipping and packaging costs.
• using the tool for a purpose other than that for which it was designed.
• the use and maintenance of the machine done in a manner not described in the user manual.
Due to our policy of continuous product improvement, we reserve the right to alter or change specications
without notice. Consequently, the product may be di󰀨erent from the information contained therein, but a
modication will be undertaken without notice if it is recognized as an improvement of the preceding
characteristic.
READ THE MANUAL CAREFULLY BEFORE USING THE MACHINE.
When ordering spare parts, please indicate the part number or code, you can nd this in the spare parts list
in this manual. Keep the purchase receipt; without it, the warranty is invalid. To help you with your product,
we invite you to contact us by phone or via our website:
• +33 (0)9.70.75.30.30
• https://services.swap-europe.com/contact
You must create a "ticket" via the web platform.
• Register or create your account.
• Indicate the reference of the tool.
• Choose the subject of your request.
• Describe your problem.
• Attach these les: invoice or sales receipt, photo
of the identication plate (serial number), photo
of the part you need (for example: pins on the
transformer plug which are broken).
8. WARRANTY
19

WHAT TO DO IF MY MACHINE BREAKS DOWN?
If you bought your product in a store:
a) Empty the fuel tank.
b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case,
the repairer will refuse the machine.
Go to the store with the complete machine and with the receipt or invoice.
If you bought your product on a website:
a) Empty the fuel tank.
b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case,
the repairer will refuse the machine.
c) Create a SWAP-Europe service ticket on the site: https://services.swap-europe.com When making the
request on SWAP-Europe, you must attach the invoice and the photo of the nameplate (serial number).
d) Contact the repair station to make sure it is available before dropping o󰀨 the machine.
Go to the repair station with the complete machine packed, accompanied by the purchase invoice and the
station support sheet downloadable after the service request is completed on the SWAP-Europe site
For machines with engine failure from manufacturers BRIGGS & STRATTON, HONDA and RATO, please
refer to the following instructions.
Repairs will be done by approved engine manufacturers of these manufacturers, see their site:
• http://www.briggsandstratton.com/eu/fr
• http://www.honda-engines-eu.com/fr/service-network-page;jsessionid=5EE8456CF39CD572AA2AEEDFD
290CDAE
• https://www.rato-europe.com/it/service-network
Please keep your original packaging to allow for after-sales service returns or pack your machine
with a similar cardboard box of the same dimensions.
For any question concerning our after-sales service you can make a request on our website https://
services.swap-europe.com
Our hotline remains available at [phone].
9. PRODUCT FAILURE
20