I-Semble 50479 User manual

1
INSTALLATION INSTRUCTIONS: HORIZONTAL WALL BED HARDWARE KIT WITH FRAME
*Our more compact model for shipping.
Rockler Woodworking and Hardware 4365 Willow Drive, Medina, MN 55340
MODEL CODES:
50479 (Twin horizontal wall bed)
53155 (Double horizontal wall bed)
58262 (Queen horizontal wall bed)
1-800-279-4441

2
A1 Head bar of the frame (with bearings) x1 x1 x1
A2 Foot bar of the frame x1 x1 x1
BCenter frame support with slat holes x2 x2 x2
CCenter frame supports x4 x4 x4
DLong center frame support x1 x1 x1
ELeft and right frame bars x2 x2 x2
FFlat bars x2 x2 x2
GPistons (non locking)
Single: 90kg, Double: 90kg, Queen: 110kg x2 x2 x2
HMattress Supports x2 x2 x2
IMounting plates (left and right) x2 x2 x2
JSaddle locking plates x2 x2 x2
KBrackets to attach wall bed to wall x3 x3 x3
LDoor brackets x8 x16 x16
MLegs (left and right) x2 x2 x2
NTube (for attaching legs) x1 x1 x1
OSlats x36 x36 x38
PSlat caps x36 x36 x38
QDouble slat caps x18 x18 x19
HARDWARE

3
RWrench x1 x1 x1
S1 Allen Key 4mm x1 x1 x1
S2 Allen Key 5mm x1 x1 x1
TThreaded inserts x16 x16 x16
UM8 x 16mm Screws x16 x16 x16
V#10 x 55mm Screws (Step 12) x26 x28 x28
W#8 x 15mm Screws (Steps 11-12) x36 x52 x52
X#10 x 15mm Screws x6 x6 x6
Y#10 x 30mm Screws x6 x6 x6
ZM5 x 15mm Screws x2 x2 x2
AA M6 x 30mm Bolts x4 x4 x4
BB M8x 50mm Bolts x22 x22 x22
CC Washers x12 x12 x12
DD Nylon Washers (for pivoting legs) x4 x4 x4
EE M5 Nuts (for saddle locks) x2 x2 x2
FF M8 Locking nuts x28 x28 x28
GG Temporary stoppers x2 x2 x2

4
Overall Cabinet Dimensions
* Suggested dimensions
Cabinet Parts Dimension Guide
DDC
C C C C
C C C C
C

5
3 1
8
"
6 15
16
"
13 7
8
"
17 3
4
"
9 7
16
"
11 7
16
"
6 1
8
"
7 3
4
"
2 1
2
"
2 1
2
"
11 7
16
"
DRILLING GUIDE
Front
Back
Bottom
All measurements are for 3/4’’ thick board.
The holes should be 3/8” in
diameter and 1/2” deep for
threaded inserts.
*See full sized template in product box.

6
Right side
Front
Front
Left side
Bottom
INSTALLING THE MOUNTING BRACKETS
1
U + T
U
I
T
I
Wood
ASSEMBLING THE CABINET
2
* See guide on page 4 for suggested cabinet dimensions.
x16
x16
x2
S2

7
ASSEMBLING THE FRAME
4
3SECURING TO THE WALL
* Professional installation recommended.
* Needs to be secured into at least
two wood or metal studs.
4.1
Insert Einto A1 and A2.
E
X=
Y=
CC=
K=
x6
x6
x12
x3
A1=
E= x2
These tabs should be at on the ground.
x1
* Nylon wall anchors are NOT recommended
X
Y
A2
A1
A2= x1
Brackets can be installed on the inside or on the
top of the cabinet.

8
4.2
Attach Dto A1 and A2 with BB and FF.
D
4.3
Attach F and B to the inside of E,
then attach the B supports to both
sides of D.
FF= x4
BB= x4
FF= x6
BB= x6
D= x1
B=
F=
x2
x2
F
F
B
B
DE
E
These tabs should be
at on the ground.
Flat bar “F”

9
4.4
Bolt both ends of the supports Cto
the frame assembly.
FF= x12
BB= x12
5INSTALLING THE SLATS
P
OP
Q
O
O
QPlace Pon one end of each slat. Attach two slats together with Q.
Insert P and Qinto their designated holes along the
frame. Insert all of the slats except for the rst and last
rows of slats. Please see next page to see which slats
to skip.
x32
x32
x16
*If necessary, use a rubber mallet to secure the slats
into the frame.
C= x4
C
C
C
C
x34
x34
x17

10
6ATTACHING THE PISTONS TO THE FRAME
FF= x2
Secure the longer metal ends of the pistons to the frame.
G= x2
FF
This end
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
For each bed size, do not insert the
rows of slats on both ends of the
frame.
Example below works for both single and double.
Queen has 19 rows of slats

11
Place the bearing into the saddle on the mounting
bracket. Secure the bearing in place with:
INSTALLING THE FRAME ONTO THE MOUNTING BRACKETS
Z
J
EE
x2
x2
x2
7

12
Tilt the frame inside past the edge of the cabinet to install the
pistons on the mounting brackets.
INSTALLING THE PISTONS TO THE CABINET
FF x2
8
9INSTALLING THE LEGS
FF
DD
N
M
x2
x4
Do not overtighten.
Install tube to both legs.
M
9.1
9.3
AA
S1
x4
AA
AA
Install the temporary stoppers GG onto the top corners of
the bed cabinet.
GG x2
Secure the legs to the bed frame.
9.2

13
10 INSTALLING THE DOOR BRACKETS
The door brackets must point downward. Install the door brackets
in alignment with the support bars on the bed frame.
Top
Bottom
11
* Install the handle on the other side of the
door during this step. Decorative handle
not included. Handle should be mounted at a
height to comfortably allow the user to pull the
bed down (approximately 1/3 of the way down
from the top of the door).
9 3/16”
35 7/16”
6” 6”
Measurements (right) are for the
placement of this hole on the
backside of the doors.
INSTALLING THE DOORS
Hook the door brackets onto the frame and push
down until they are rmly in place. Center the
doors on the frame.
11.1
9 3/16”
41 7/16”
Twin:
1 door
Double/Queen:
4 doors
L
W
x8
x16
x16
x32
15”
9 3/16”
19 7/16”
12”
12” 15”

14
Attach the doors to the frame while putting weight on
the frame to keep the bed open. We recommend to have
someone else sit on the frame during this step.
* The bed will not stay open on its own without the
weight of a mattress.
V
W
V
Wx 20
x 26
11.2
For this step x 2
12
x 20
x 28
INSTALLING THE STOPPER
Install the permanent stopper on the inside
top of the cabinet while putting weight on
the frame to keep the bed open. it must be
placed where it will allow for the door to
close ush to the front of the cabinet.
Stopper

15
INSTALLING THE MATTRESS SUPPORTS
Insert the mattress supports into the
designated holes on the bed frame. H
13
Hx 2
INSTALLING THE REMAINING SLATS
14
P
O
x4
x4
x2
P
Q
O
O
Q
Insert Pand Qinto their designated holes
along the frame. Insert all of the remaining
slats.

16
.
.
The wall bed is assembled and shown in
lowered position.
Pivot the leg towards the inside of the unit. Make
sure that the leg is fully retracted.
Pull up gently to close. The leg serves as a mattress
retaining system. The pistons insure that the door
closes properly and remains closed.
OPERATING ALL I-SEMBLE WALL BEDS WITH NON-LOCKING PISTONS**
Double
Queen
39” x 75’’
54” x 75’’
60” x 80‘’
454 kg (1000 lbs)
136 kg (300 lbs)
154 kg (340 lbs)
181 kg (400 lbs)
Bed Size Mattress Size *Mattress not included Load Rating
Dynamic Static
Twin
* The bed will not stay open on its own without the weight of a mattress.
Thickness
10”
RCKLR100HKD-V1
** I-SEMBLE model may vary.