I-Semble 54877 User manual

1
INSTALLATION INSTRUCTIONS: VERTICAL WALL BED HARDWARE KIT WITH FRAME
*Our more compact model for shipping.
Rockler Woodworking and Hardware 4365 Willow Drive, Medina, MN 55340
MODEL CODES:
54877 (Single vertical wall bed)
55991 (Double vertical wall bed)
54386 (Queen vertical wall bed)
1-800-279-4441

2
ALeft and right of the frame x2 x2 x2
BUpper and lower half frame supports x4 x4 x4
CMiddle frame supports x2 x2 x2
DLong center frame support x1 x1 x1
EUpper and lower frame supports x2 x2 x2
FFlat bars x2 x2 x2
GPistons (non locking) x2 x2 x2
HMattress Supports x1 x2 x2
IMounting plates (left and right) x2 x2 x2
JSaddle locking plates x2 x2 x2
KBrackets to attach wall bed to wall x2 x2 x2
LDoor brackets x6 x12 x12
MLegs (left and right) x2 x2 x2
NTube (for attaching legs) x1 x1 x1
OSlats x40 x40 x42
PSlat caps x40 x40 x42
QDouble slat caps x20 x20 x21
HARDWARE

3
RWrench x1 x1 x1
S1 Allen Key #4 x1 x1 x1
S2 Allen Key #5 x1 x1 x1
TThreaded inserts x16 x16 x16
UM8 x 16mm Screws x16 x16 x16
V#10 x 55mm Screws (Step 12) x26 x26 x26
W#8 x 15mm Screws (Steps 11-12) x32 x52 x52
X#10 x 15mm Screws x4 x4 x4
Y#10 x 30mm Screws x4 x4 x4
ZM5 x 15mm Screws x2 x2 x2
AA M6 x 30mm Bolts x4 x4 x4
BB M8x 50mm Bolts x34 x34 x34
CC Washers x8 x8 x8
DD Nylon Washers (for pivoting legs) x4 x4 x4
EE M5 Nuts (for saddle locks) x2 x2 x2
FF M8 Locking nuts x40 x40 x40
GG Temporary stoppers x2 x2 x2

4
*All measurements are for 19mm (3/4'') board
E
Single
E E
Double
E E
Queen
A= Exterior
B-C-D-E = Inset
SINGLE WALL BED
#Qty
A 2
B 2
C 1
D 1
E 1
F 1
DOUBLE WALL BED
#Qty
A 2
B 2
C 1
D 1
E 2
F 1
QUEEN WALL BED
#Qty
A 2
B 2
C 1
D 1
E 2
F 1
* Suggested dimensions
31 9/16
3
in
3/4
3/4
3/4
3/4
3/4
5/8
in
83 1/2
63 5/16
63 5/16
63 5/16
81 3/4
18
in
16
16
13
26
3/4
3/4
3/4
3/4
5/8
76 3/4
18
in
16
16
in
78 1/2
57 1/4
## #########
## #########
41 1/8
3
in
3/4
3/4
3/4
3/4
3/4
5/8
in
78 1/2
41 3/8
41 3/8
41 3/8
78 1/2
83 1/2
in
## #########
## #########
Thickness
Length
Width
in
41 3/8
57 1/4
63 5/16
in
14 1/2
14 1/2
14 1/2
in
77
## #########
## #########
in
Queen
Outside Measurements
Width
Depth
Height
Single
Double
42 7/8
58 3/4
64 13/16
in
## #########
## #########
## #########
in
78 1/2
Panneaux
19mm
VERTICAL WALL BED
Conversion Table
DIMENSIONS
3/4''
Panels
Queen
Inside Measurements
Width
Depth
Height
Single
Double
Width
Length
Thickness
Length
Thickness
Width
13
26
28 1/2
3
57 1/4
57 1/4
76 3/4
18
in
3/4
A
A
B
B
D
C
A
A
B
C
B
D
E
F
Overall Cabinet Dimensions
* Suggested dimensions
Cabinet Parts Dimension Guide

5
3 1
8
"
6 15
16
"
13 7
8
"
17 3
4
"
9 7
16
"
11 7
16
"
6 1
8
"
7 3
4
"
2 1
2
"
2 1
2
"
11 7
16
"
DRILLING GUIDE
Front
Back
Bottom
All measurements are for 3/4’’ thick board.
The holes should be 3/8” in
diameter and 1/2” deep for
threaded inserts.
*See full sized template in product box.

6
Right side
Front
Front
Left side
Bottom
INSTALLING THE MOUNTING BRACKETS
1
U + T
U
I
T
I
Wood
ASSEMBLING THE CABINET
2
* See guide on page 4 for suggested cabinet dimensions.
x16
x16
x2
S2

7
ASSEMBLING THE FRAME
4
3SECURING TO THE WALL
* Professional installation recommended.
* Needs to be secured into at least
two wood or metal studs.
4.1
Attach Band Cto Afor both the
right and left sides of the frame.
B
B
C
A
FF=
BB=
X=
Y=
CC=
K=
x4
x4
x8
x2
A=
B=
C=
x4
x2
*Ensure that all of the tabs are
pointing towards each other.
These tabs should be at on the ground.
S
x12
x12
x2
*Nylon wall anchors are NOT recommended
X
Y

8
4.2
Attach Eand F to D.
E
E
D
4.3
Insert E into the assemblies from
step 4.1.
F
F
FF= x4
BB= x4
FF= x6
BB= x6
D=
E=
F=
All tabs should be facing the oor.
x1
x2
x2
The tabs on Emust face the inside
of the frame.

9
4.4
Bolt Fto the two frame halves from
step 4.1.
FF= x12
BB= x12
5INSTALLING THE SLATS
P
OP
Q
O
O
QPlace Pon one end of each slat. Attach two slats together with Q.
Insert P and Qinto their designated holes along the
frame. Insert all of the slats except for 4 for the single
and double, and 6 for the queen (please see next page
to see which slats to skip).
x36
x36
x18
*If necessary, use a rubber mallet to secure the slats
into the frame.

10
6ATTACHING THE PISTONS TO THE FRAME
FF= x2
Secure the longer metal ends of the pistons to the frame.
G= x2
FF
This end
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Start from this side.
For each bed size, do not insert
slats in row #8, or the slats in the
last row. For the queen size, please
do not insert slats in row #11 as
well.
Example below works for both
single and double.
#8
Last
Pivot point
Pivot point
Please do not insert slats in row 11 for the queen

11
Place the bearing into the saddle on the mounting
bracket. Secure the bearing in place with:
INSTALLING THE FRAME ONTO THE MOUNTING BRACKETS
Z
J
EE
x2
x2
x2
7

12
Tilt the frame inside past the edge of the cabinet to install the pistons
on the mounting brackets.
INSTALLING THE PISTONS TO THE CABINET
FF x2
8
INSTALLING THE STOPPER
Install the permanent stopper on the inside top of
the cabinet where it will allow for the door to close
ush to the front of the cabinet.
9
Stopper
Install the temporary stoppers GG onto the
top corners of the bed cabinet.
GG x2

13
INSTALLING THE LEGS
FF
DD
N
M
x2
x4 Do not overtighten.
Install tube to both legs.
M
10.1
10.2
AA
S1
x4
10
INSTALLING THE DOOR BRACKETS
Lx12
The door brackets must point downward. Install the door brackets
in alignment with the support bars on the bed frame.
AA
Top
Bottom
AA
Wx 24
11
* Install the handle on the other side of the door during this step.
Decorative handle not included. Handle should be mounted
at a height to comfortably allow the user to pull the bed down
(approximately 1/3 of the way down from the top of the door).
x 6
x12
10 3/8”
27 5/16”
27 5/16”
10 3/8”
30 3/4”
30 3/4”
6” 6”
Measurements (right) are for the
placement of this hole on the
backside of the doors.
Secure the legs to the bed frame.

14
INSTALLING THE DOORS
Hook the door brackets onto the frame and push down until they are
rmly in place. Center the doors on the frame.
Attach the doors to the frame while putting weight on the frame to keep the bed
open. We recommend to have someone else sit on the frame during this step.
* The bed will not stay open on its own without the weight of a mattress.
V
W
V
Wx 20
x 26
12.1
12.2
For this step x 2
12
x 28
x 26

15
INSTALLING THE MATTRESS SUPPORTS
Insert the mattress supports into the
designated holes on the bed frame.
H
13
Hx 2
INSTALLING THE REMAINING SLATS
14
P
O
x4
x4
x2
P
Q
O
O
Q
Insert Pand Qinto their designated holes along the
frame. Insert all of the remaining slats.
x 1
x6
x6
x3

16
.
.
The wall bed is assembled and shown in
lowered position.
Pivot the leg towards the inside of the unit. Make
sure that the leg is fully retracted.
Pull up gently to close. The leg serves as a mattress
retaining system. The pistons insure that the door
closes properly and remains closed.
USING THE WALL BED
Double
Queen
39” x 75’’
54” x 75’’
60” x 80‘’
454 kg (1000 lbs)
136 kg (300 lbs)
154 kg (340 lbs)
181 kg (400 lbs)
Bed Size Mattress Size *Mattress not included Load Rating
Dynamic Static
Single
* The bed will not stay open on its own without the weight of a mattress.
Thickness
10”
RCKLR100KD-R2