I-Tech USB Hub DB-15 IP 2-console KVM User manual

NV Series User Manual
USB Hub DB-15 KVM
NV800H / NV1600H
USB Hub DB-15
2-console KVM
NVIP800H / NVIP1600H
USB Hub DB-15 2-
console KVM
NVCE800H / NVCE1600H
i-Tech Company LLC
TOLL FREE: [phone] • EMAIL: [email protected] • WEB: www.iTechLCD.com

Legal Information
First English printing, October 2002
Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness
of the contents. The information in this document is subject to change without notice. We are not liable for any injury or
loss that results from the use of this equipment.
Safety Instructions
Please read all of these instructions carefully before you use the device. Save this manual for
future reference.
■Unplug equipment before cleaning. Don’t use liquid or spray detergent; use a moist cloth.
■Keep equipment away from excessive humidity and heat. Preferably, keep it in an air-conditioned environment with
temperatures not exceeding 40º Celsius (104º Fahrenheit).
■When installing, place the equipment on a sturdy, level surface to prevent it from accidentally falling and causing
damage to other equipment or injury to persons nearby.
■When the equipment is in an open position, do not cover, block or in any way obstruct the gap between it and the
power supply. Proper air convection is necessary to keep it from overheating.
■Arrange the equipment’s power cord in such a way that others won’t trip or fall over it.
■If you are using a power cord that didn’t ship with the equipment, ensure that it is rated for the voltage and current
labeled on the equipment’s electrical ratings label. The voltage rating on the cord should be higher than the one listed
on the equipment’s ratings label.
■Observe all precautions and warnings attached to the equipment.
■If you don’t intend on using the equipment for a long time, disconnect it from the power outlet to prevent being
damaged by transient over-voltage.
■Keep all liquids away from the equipment to minimize the risk of accidental spillage. Liquid spilled on to the power
supply or on other hardware may cause damage, fire or electrical shock.
■Only qualified service personnel should open the chassis. Opening it yourself could damage the equipment and
invalidate its warranty.
■If any part of the equipment becomes damaged or stops functioning, have it checked by qualified service personnel.
What the warranty does not cover
■Any product, on which the serial number has been defaced, modified or removed.
■Damage, deterioration or malfunction resulting from:
□Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or
failure to follow instructions supplied with the product.
□Repair or attempted repair by anyone not authorized by us.
□Any damage of the product due to shipment.
□Removal or installation of the product.
□Causes external to the product, such as electric power fluctuation or failure.
□Use of supplies or parts not meeting our specifications.
□Normal wear and tear.
□Any other causes which does not relate to a product defect.
■Removal, installation, and set-up service charges.
Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
■Re-position or relocate the receiving antenna.
■Increase the separation between the equipment and receiver.
■Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4.1 KVM Button
4.2 Password
4.3 KVM OSD
4.4 KVM Hotkey & Remote Console Hotkey
4.5 DC Power Option : 12V / 24V / 48V / 125V
NVIP800H NVIP1600H
1.1 Package contents
1.2 KVM port connection
1.3 IP & Local console connection
1.4 IP console setting
1.5 Important Preconfiguration for IP console
1.6 Built-in USB hub usage & connection
1.7 Specifications
NV800H NV1600H
3.1 Package contents
3.2 KVM port connection
3.3 Built-in USB hub usage & connection
3.4 Specifications
NVCE800H NVCE1600H
2.1 Package contents
2.2 KVM port connection
2.3 Remote & Local console connection
2.4 Built-in USB hub usage & connection
2.5 Specifications
Contents
< Part 1 > USB Hub DB-15 2-console KVM
< Part 2 > USB Hub DB-15 2-console KVM
P. 1
P. 2
P. 3
P. 4
P.5 - 7
P. 8
P. 9
P.10
P. 11
P.12 - 13
P.14
P.15
P.20
P.21
P.22
P.23
P.24
< Part 4 > Usage
< Part 3 > USB Hub DB-15 KVM
P.16
P.17
P.18
P.19

AB
Figure 1.
■It is very important to mount the equipment in a suitable cabinet or on a stable surface.
■Make sure the place has a good ventilation, is out of direct sunlight, away from sources of excessive
dust, dirt, heat, water, moisture and vibration.
The equipment comes with the standard parts shown in package content. Check and make sure they are
included and in good condition. If anything is missing, or damaged, contact the supplier immediately.
Unpacking
Before Installation
Installation for standalone KVM
■Install each bracket using screws
provided shown in Figure 1.
M3.2 x 4.5 mm M4 x 10 mm
■Fix the KVM into the rack
Screw A: 2 pcs Screw B: 8 pcs

KVM unit
Daisy-chain feature for this model is NOT available.
NVIP800H
Local Console
Flash 12VDC
2 x USB 2.0
( USB hub for device connection )
NVIP1600H
P. 1
NVIP800H / NVIP1600H
< 1.1 > Package Contents USB Hub DB-15 IP KVM
< Part 1 > USB Hub DB-15 KVM
•
NVIP800H or NVIP1600H KVM unit x 1
• Mounting set w/ bracket & screws x 1
• Power adapter w/ power cord ( for KVM ) x 1

DB-15 USB KVM port
CB-6 / CB-10 / CB-15
■6 / 10 / 15 ft USB KVM cable
■Support USB server
< 1.2 > KVM port connection
P. 2
USB Hub DB-15 IP KVM
USB Servers
USB Servers
CB - 6 / 10 / 15 USB KVM cable
support USB server

Resolution Support Frequency
( Hz )
1600 x 1200 60
1280 x 1024 60
1024 x 768 60 / 70 / 75
IP Console
< 1.3 > IP & Local console connection
CAT 5 / 6 cable
Network device
hub or router
P. 3
USB Hub DB-15 IP KVM

After the cable connection, please take the following steps to configure the IP KVM :
1. Download IPKVMsetup.exe from the link:
www.austin-hughes.com/support/utilities/cyberview/IPKVMsetup.exe
2. Double click IPKVMsetup.exe to configure the IP KVM by device setup as below.
< 1.4 > IP console setting
- http://192.168.1.22
11. Open Internet Explorer ( I.E. ), version 6.0 or above
12. Enter the IP KVM address into the address bar
- For Single IP - http://192.168.1.22
13. Enter username ( default is super )
Password ( default is pass )
14. After successful login to IP KVM, the user will enter the main page of IP KVM
The setting is enough for intranet.
If the users access KVM GUI via internet, please ask MIS for assistance and
download IP KVM user manual from the link :
www.austin-hughes.com/support/usermanual/cyberview/UM-CV-IP.pdf
3. Click Refresh Device to search the connected IP KVM
4. Select the M.A.C. address, which you want to setup, then click Query Device
5. Enter Super user login. The default is super
6. Enter Super user password. The default is pass
7. Enter the new super user password
8. Re-enter the new password
9. Change the desired IP address / Subnet mask / Gateway, then click Setup Device to confirm the setting to IP KVM
10. The default address is as below:--
■
The single IP KVM model, such as NVIP1600H
P. 4
USB Hub DB-15 IP KVM

< 1.5 > Important Preconfiguration for IP console USB Hub DB-15 IP KVM
P. 5
( 1 ) TARGET SERVER SETUP
Resolution
The IP KVM remote console recognizes several varieties of video display formats with resolutions up to 1600 x
1200 @60Hz. (Refer to the User Manual for a list of supported video formats). Minimize bandwidth by setting the
target server’s video resolution to the minimum setting required for your remote monitoring application.
The following video modes are recommended:
(i) 1024 x 768 @ 60Hz
(ii) 1280 x 1024 @ 60Hz
On a Windows target server system, select Control Panel > Display > Settings.
Modify the screen resolution value as necessary.
Mouse
Use generic mouse drivers for optimum mouse control during remote sessions. Set the mouse pointer speed to a
middle setting with no acceleration or snap-to effects.
On a Windows target server system, select Control Panel > Mouse > Pointer Options
Set the pointer speed to medium and disable Enhanced pointer precision
For Linux GUIs, set the mouse acceleration to exactly 1 and the threshold to exactly 1.
You must complete the following tasks after the IP console setting is performed.
If your keyboard keeps repeating keys when it is plugged into the KVM. Please follow either one below :
( a. )
Enable key release timeout if you experience duplicated keystrokes during poor network performance.
- login to IP KVM remote console
- go to Interfaces KVM settings > Keyboard / Mouse
- click the Key Release Timeout
- adjust Timeout after if necessary
( b. )
Reduce video bandwidth usage if you experience duplicated keystrokes during poor network
- login to IP KVM remote console
- go to Interfaces KVM Settings > User Console > Transmission Encoding,
- select Manually
- adjust Compression to [ 0-none ] and Color depth to [ 8-bit – 256 col ]
**Servers connected to KVM

USB Hub DB-15 IP KVM
< 1.5 > Important Preconfiguration for IP console
P. 6
JAVA Update for IP KVM
Due to the latest update from Java security, customer may face the "JAVA Block" message while accessing
the remote console over IP as below :
If it said so, please download the latest IP KVM firmware ( version aust-i11-150608 ) from the link below :
http://www.austin-hughes.com/resources/software/kvm-switch
Then follow the attached steps to update the firmware.
Firmware Update Steps
1) Download the latest IP KVM firmware ( version aust-i11-150608 ) from the link
http://www.austin-hughes.com/resources/software/kvm-switch
2) Login the IP KVM
3) Click < Update Firmware >
4) Click < Browse > to select the firmware file
5) Click < Upload >
( 2 ) REMOTE CLIENT COMPUTER SETUP
The remote client computer must have a web browser ( such as Microsoft Internet Explorer, Mozilla Firefox,
and Netscape Navigator ) and a Java Virtual Machine ( version 1.4 or higher ) installed. Enable Java on the
web browser.

6) Click < Update >
After the firmware has been updated, IP KVM will reset automatically.
After one minute, you will be redirected to the Login page and requested to login again.
- Completed
P. 7
USB Hub DB-15 IP KVM

P. 8
< 1.6 > Built-in USB Hub Usage & Connection USB Hub DB-15 IP KVM
2 x USB 2.0 ( USB hub for device connection )
Printer
Scanner
Flash Disk
Keyboard / Mouse
Hard disk storage
Camera

< 1.7 > Specifications
P. 9
NVIP800H NVIP1600H
▀KVM Port
Number of ports : 8 or 16
Connector : DB-15 combo connector
Connectivity : Combo 2-in-1 VGA + USB KVM cable, 6, 10 or 15 feet
▀Local Console
Graphic connector : 1 x DB-15
Input device : 2 x USB type A for keyboard & mouse
USB hub : 2 x USB type A for sharing other peripheral devices among the computers
Resolution support : 4:3 - max. 1600 x 1200, 16:10 - max. 1920 x 1200
▀IP Remote Console
Connector : RJ45 Ethernet
User management : 15-user login, 1 x active user
Network protocol : DHCP / BOOTP / DNS
Security : SSL v3, RSA, AES, HTTP / HTTPs, CSR
Browser : IE, Firefox, Safari, Netscape
Resolution support : 4:3 - max. 1600 x 1200
▀Compatibility
Hardware : HP / IBM / Dell PC, Server and Blade Server
SUN / Mac
OS Support : Windows / Linux / Unix / Mac OS
▀Power
Input : Auto sensing 100 to 240VAC, 50 / 60 Hz
Option DC : 12V / 24V / 48V / 125V DC input
Consumption : Max. 18W
▀Regulatory
Safety : FCC & CE certified
Environment : RoHS2 & REACH compliant
▀Environmental Operating Storage / Non-operating
Temperature : 0 to 55°C degree -20 to 60°C degree
Humidity : 20~90%, non-condensing 5~90%, non-condensing
Altitude : 16,000 ft 40,000 ft
Shock : - 10G acceleration (11ms duration)
Vibration : - 5~500Hz 1G RMS random
▀Product Information
Dimension (W x D x H) : 443 x 171 x 44 mm / 17.4 x 6.7 x 1.73 inch
Net weight : 3 kg / 6.5 lb
▀Packing Information
Dimension (W x D x H) : 500 x 400 x 90 mm / 19.7 x 15.7 x 3.5 inch
Gross weight : 5 kg / 11 lb
USB Hub DB-15 IP KVM

KVM unit
•
NVCE800H or NVCE1600H KVM unit x 1
• Mounting set w/ bracket & screws x 1
• Power adapter w/ power cord ( for KVM ) x 1
• Receiver box for remote console x 1
• Power adapter w/ power cord ( for receiver ) x 1
• CE-6 6ft Combo KVM cable for receiver box x 1
< 2.1 > Package Contents
P.10
Part 2. USB Hub DB-15 2-console KVM
USB Hub DB-15 2-console KVM
NVCE800H / NVCE1600H
NVCE800H
Remote
NVCE1600H
Daisy-chain feature for this model is NOT available.
Local Console
12VDC
2 x USB 2.0
( USB hub for device connection )

DB-15 USB KVM port
CB-6 / CB-10 / CB-15
■6 / 10 / 15 ft USB KVM cable
■Support USB server
USB Servers
USB Servers
CB - 6 / 10 / 15 USB KVM cable
support USB server
USB Hub DB-15 2-console KVM
< 2.2 > KVM port connection
P. 11

UM-CV-751-USBKVM-Q218V1 www.austin-hughes.com
CAT 5 / 6 cable
Receiver
Remote
USB console
Local
USB
console
Remote
Cat6
Console
For remote console, max. cable length is
subject to the resolution.
Please refer to the tables below.
< 2.3 > Remote & Local console connection USB Hub DB-15 2-console KVM
P.12
Resolution Support Frequency
( Hz )
Max. Cat6 Cable
Length ( M )
1920 x 1080 60 50
1920 x 1200 60 50
1600 x 1200 60 100
1440 x 900 60 100
1280 x 1024 60 150
1024 x 768 60 / 70 / 75 150
Remote Console

Remote
Console
Cat6 cable
up to 150m
How to use a receiver to connect a remote console
P.13
USB Hub DB-15 2-console KVM
VGA
Power KB
Mouse
Local
Computer Remote I/O
Front
Remote
LED
Local
LED
Rear
Select button
Receiver
12V DC Power
Adapter
CE-6
Combo
KVM cable
Local computer
( Optional setup )
Monitor
VGA
cable
The receiver provides a hotkey function for remote console. Please refer to P.23
Front

< 2.4 > Built-in USB Hub Usage & Connection USB Hub DB-15 2-console KVM
2 x USB 2.0 ( USB hub for device connection )
Printer
Scanner
Flash Disk
Keyboard / Mouse
Hard disk storage
Camera
P.14

UM-CV-751-USBKVM-Q218V1 www.austin-hughes.com
NVCE800H
CV-1602H
▀KVM Port
Number of ports : 8 or 16
Connector : DB-15 combo connector
Connectivity : Combo 2-in-1 VGA + USB KVM cable, 6, 10 or 15 feet
▀Local Console
Graphic connector : 1 x DB-15
Input device : 2 x USB type A for keyboard & mouse
USB hub : 2 x USB type A for sharing other peripheral devices among the computers
Resolution support : 4:3 - max. 1600 x 1200, 16:10 - max. 1920 x 1200
▀Remote Console
Connector : 1 x DB 15-pin, VGA
Input device : 2 x USB type A for keyboard & mouse
Remote I/O : RJ45 via Cat5 / Cat5e / Cat6 cable up to 150m
Compensation : Auto adjust for cable length
Resolution support : 4: 3 - max. 1600 x 1200
16: 9 - max. 1920 x 1080
16:10 - max. 1920 x 1200
▀Compatibility
Hardware : HP / IBM / Dell PC, Server and Blade Server
SUN / Mac
OS Support : Windows / Linux / Unix / Mac OS
▀Power
Input: Auto sensing 100 to 240VAC, 50 / 60 Hz
Option DC : 12V / 24V / 48V / 125V DC input
Consumption : Max. 12W
▀Regulatory
Safety : FCC & CE certified
Environment : RoHS2 & REACH compliant
▀Environmental Operating Storage / Non-operating
Temperature : 0 to 55°C degree -20 to 60°C degree
Humidity : 20~90%, non-condensing 5~90%, non-condensing
Altitude : 16,000 ft 40,000 ft
Shock : - 10G acceleration (11ms duration)
Vibration : - 5~500Hz 1G RMS random
▀Product Information
Dimension (W x D x H) : 443 x 171 x 44 mm / 17.4 x 6.7 x 1.73 inch
Net weight : 3 kg / 6.5 lb
▀Packing Information
Dimension (W x D x H) : 500 x 400 x 90 mm / 19.7 x 15.7 x 3.5 inch
Gross weight : 5 kg / 11 lb
< 2.5 > Specifications USB Hub DB-15 2-console KVM
P.15

•
NV800H or NV1600H KVM unit x 1
• Mounting set w/ bracket & screws x 1
• Power cord ( for KVM ) x 1
< 3.1 > Package Contents
P.16
Part 3. USB Hub DB-15 KVM
USB Hub DB-15 KVM
CV-801H
CV-1601H
Daisy-chain feature for this model is NOT available.
Local Console
2 x USB 2.0
( USB hub for device connection )
Power
KVM unit
NV800H / NV1600H
12VDC